Home › Vehicle Interior › EXTERIOR › ROOF DRIP SIDE FINISH MOULDING
RM2850E _58 Vehicle Interior _073214 EXTERIOR _0356379 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR  ROOF DRIP SIDE FINISH MOULDING  INSTALLATION  


PROCEDURE

Hide 75561F 1.INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP

NOTICE:
·

It is only necessary to perform this procedure when replacing a roof drip side finish moulding clip with a new one.

·

If installing new roof drip side finish moulding clips, remove the adhesive remaining where the roof drip side finish moulding clips will be installed on the vehicle body and clean the vehicle body with a non-residue solvent.



HINT:

When installing a roof drip side finish moulding clip, heat the vehicle body and roof drip side finish moulding clip using a heat light.


Standard
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Roof Drip Side Finish Moulding Clip 20 to 30°C (68 to 86°F)

NOTICE:

Do not the vehicle body or roof drip side finish moulding clip excessively.


a.

Clean the vehicle body surface.

i.

Remove the double-sided tape from the vehicle body.


ii.

Wipe off any tape adhesive residue with cleaner.



b.
B187426E11
2.094,0.813 2.365,0.813 false 0.927,1.073 1.167,1.073 1.167,1.073 1.302,1.521 true 1.906,0.708 2.25,0.958 0.344,0.25 10 false *a 0.74,0.99 1.146,1.229 0.406,0.24 10 false *b

Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to new roof drip side finish moulding clips.

Text in Illustration
*a Adhesive
*b 2 to 3 mm Bead of Adhesive

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1991 psi) or more (when the temperature is 23°C (73°F).



c.

Apply primer to the body where the roof drip side finish moulding clip will be installed.

NOTICE:

Do not let the primer dry.



d.

While using the position shown in the illustration as a reference, place the roof drip side finish moulding clip on to the roof panel. Then position and install the clip using the locations on the roof panel after lightly pressing it so that the adhesive adheres to the primer

B460178E01
4.635,1.333 4.635,1.208 4.635,1.208 5.01,1.208 true 5.063,1.594 5.344,1.75 0.281,0.156 10 false *a 3.292,0.844 3.521,1.01 0.229,0.167 10 false *a 2.542,1.135 2.771,1.302 0.229,0.167 10 false *b 3.781,1.135 4.01,1.302 0.229,0.167 10 false *c 4.563,1.354 4.792,1.521 0.229,0.167 10 false *d

Text in Illustration
*a 6.67 mm (0.263 in.) *b 5.11 mm (0.201 in.)
*c 5.23 mm (0.206 in.) *d Edge of Curved Surface

NOTICE:

Install the center roof drip side moulding when 40 minutes or more have elapsed after pressing and installing the roof drip side finish moulding clips.


HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 48 hours




Hide 75552H 2.INSTALL ROOF DRIP SIDE MOULDING LH

HINT:

When installing the roof drip side moulding LH, heat the vehicle body and roof drip side moulding LH using a heat light.


Standard
Item Temperature
Vehicle Body 40 to 60 °C (104 to 140 °F)
Roof Drip Side Moulding LH 20 to 30 °C (68 to 86 °F)

NOTICE:
·

Do not heat the vehicle body or roof drip side moulding LH excessively.

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

Attach the clip to install the roof drip side moulding LH.


Hide 75551H 3.INSTALL ROOF DRIP SIDE MOULDING RH

HINT:

Use the same procedure described for the LH side.