Home › Vehicle Interior › EXTERIOR › SIDE STRIPE TAPE (for Folding Type)
RM2850E _58 Vehicle Interior _073214 EXTERIOR _0356387 SIDE STRIPE TAPE(for Folding Type) A

EXTERIOR  SIDE STRIPE TAPE(for Folding Type)  INSTALLATION  


PROCEDURE

Hide 1. REPAIR INSTRUCTION

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.

NOTICE:
·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




ii.

Wipe off any tape adhesive residue with cleaner.



b.

Installation temperature.

i.

When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) using a heat light.

When the ambient temperature is higher than 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.





c.

Before installation.

i.

Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.




d.

Key points for handling the tape.

i.

The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

NOTICE:

Do not bend the tape or leave it in a place with a high temperature.




e.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for corners).

i.

Remove the release paper and apply the tape carefully with your fingers.


ii.

Before applying the tape to each corner, heat the tape using a heat light and gradually apply it to avoid wrinkles in the tape and achieve a neat finish.



f.

Check after installation.

i.

After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, apply new tape.

NOTICE:

Do not reuse the tape.




Hide 75999G 2.INSTALL LOWER QUARTER STRIPE

HINT:

When installing the lower quarter stripe, heat the vehicle body and lower quarter stripe using a heat light.


Standard
Item Temperature
Vehicle Body 40 to 60 °C (104 to 140 °F)
Lower Quarter Stripe 20 to 30 °C (68 to 86 °F)

NOTICE:
·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.
B620108N01
1.292,1.531 1.448,1.729 0.156,0.198 10 false A 1.313,1.042 1.469,1.24 0.156,0.198 10 false A 1.281,3.396 1.885,3.615 0.604,0.219 10 false A-A

Apply primer to the positions shown in the illustration.


b.

Temporarily align the lower quarter stripe in the positions shown in the illustration.

B619496N01
4.427,3.042 4.74,3.24 0.313,0.198 10 false *b 1.385,0.427 1.698,0.625 0.313,0.198 10 false *a 4.177,0.396 4.49,0.594 0.313,0.198 10 false *a

Text in Illustration
*a 1.0 mm (0.0394 in.) *b 8.0 mm (0.315 in.)


c.
B619497

Peel peeling paper approximately 30 mm at a time and then press the lower quarter stripe into place by moving a squeegee from the center outward in a fan-shaped pattern.


d.
B619498

Press both ends of the door panel into place using a squeegee.


e.
B619499

Press the curved area of the door panel into place using a squeegee.


f.
B619501

Press the recessed area of the door panel into place using a squeegee.


g.

Fold the end of the lower quarter stripe and press it into place.

B619500N01
4.479,2.938 4.667,2.781 true 1.99,2.781 2.208,2.896 true 1.635,0.573 1.792,0.771 0.156,0.198 10 false C 1.635,1.948 1.792,2.146 0.156,0.198 10 false C 1.052,1.344 1.208,1.542 0.156,0.198 10 false A 1.594,1.344 1.75,1.542 0.156,0.198 10 false A 2.354,1.344 2.479,1.521 0.125,0.177 10 true B 2.906,1.333 3.031,1.51 0.125,0.177 10 true B 6.073,0.073 6.448,0.229 0.375,0.156 10 false C-C 2.125,3.219 2.5,3.375 0.375,0.156 10 false B-B 4.51,3.229 4.885,3.385 0.375,0.156 10 false A-A 1.729,2.948 1.979,3.115 0.25,0.167 10 false *a 2.229,2.865 2.479,3.031 0.25,0.167 10 false *c 4.323,2.885 4.573,3.052 0.25,0.167 10 false *c 4.885,2.854 5.135,3.021 0.25,0.167 10 false *a 5.948,2.76 6.198,2.927 0.25,0.167 10 false *b

Text in Illustration
*a 1.0 mm (0.0394 in.) *b 8.0 mm (0.315 in.)
*c Edge of Curved Surface - -


Hide 75991F 3.INSTALL LOWER QUARTER STRIPE RH

HINT:

Use the same procedure as for the lower quarter stripe.


Hide 75941B 4.INSTALL NO. 1 CENTER PILLAR STRIPE

HINT:

When installing the No. 1 center pillar stripe, heat the vehicle body and No. 1 center pillar stripe using a heat light.


Standard
Item Temperature
Vehicle Body 40 to 60 °C (104 to 140 °F)
No. 1 Center Pillar Stripe 20 to 30 °C (68 to 86 °F)

NOTICE:
·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.
B628101N01
1.229,1.115 1.625,0.948 false 1.021,1.063 1.333,1.26 0.313,0.198 10 false *a

Peel the inner portion of the peeling paper on the No. 1 center pillar stripe.

Text in Illustration
*a Inner Portion


b.
B619506

Using a squeegee, press the No. 1 center pillar stripe sealer (horizontal direction) into place, as shown in the illustration.


c.
B619507

Using a squeegee, press the No. 1 center pillar stripe sealer (vertical direction) into place, as shown in the illustration.


d.
B466139N02
1.375,3.74 1.167,3.302 1.167,3.302 1.688,3.427 true 0.781,1.156 0.938,1.333 0.156,0.177 10 false A 1.5,1.344 1.656,1.542 0.156,0.198 10 false A 1.448,2.333 1.76,2.51 0.313,0.177 10 false A-A 1.792,3.781 2.042,4 0.25,0.219 10 false *a 1.01,3.188 1.24,3.375 0.229,0.188 10 false *b

Check that the No. 1 center pillar stripe is installed in the position shown in the illustration.

Text in Illustration
*a 3.0 mm (0.118 in.)
*b Edge of Curved Surface


Hide 75942 5.INSTALL NO. 2 CENTER PILLAR STRIPE

HINT:

Use the same procedure as for the No. 1 center pillar stripe.


Hide 75992C 6.INSTALL QUARTER STRIPE LH

HINT:

When installing the quarter stripe LH, heat the vehicle body and quarter stripe LH using a heat light.


Standard
Item Temperature
Vehicle Body 40 to 60 °C (104 to 140 °F)
Quarter Stripe LH 20 to 30 °C (68 to 86 °F)

NOTICE:
·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

Install the quarter stripe LH so that it overlaps with the No. 1 center pillar stripe and front side panel stripe LH as shown in the illustration.

B466140N02
1.573,0.875 1.677,0.813 true 1.396,2.177 1.5,2.115 true 5.552,1.948 5.302,1.583 5.302,1.583 5.635,1.458 true 5.917,1.948 6.104,2.115 0.188,0.167 10 false *a 1.01,1.979 1.198,2.146 0.188,0.167 10 false *a 6,1.5 6.188,1.667 0.188,0.167 10 false *a 1.083,0.573 1.271,0.729 0.188,0.156 10 true *a 1.49,2.01 1.677,2.177 0.188,0.167 10 false *b 1.458,1.677 1.646,1.844 0.188,0.167 10 false *c 1.521,0.323 1.708,0.469 0.188,0.146 10 true *c 1.667,0.708 1.833,0.854 0.167,0.146 10 true *b 5.146,1.521 5.333,1.688 0.188,0.167 10 false *b 2.323,1.229 2.51,1.375 0.188,0.146 10 false A 3.063,1.469 3.25,1.615 0.188,0.146 10 false A 6,0.198 6.365,0.344 0.365,0.146 10 false A-A

Text in Illustration
*a 3.0 mm (0.118 in.) *b Edge of Curved Surface
*c Over Lap - -


Hide 75991C 7.INSTALL QUARTER STRIPE RH

HINT:

Use the same procedure as for the quarter stripe LH.