Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2017.01–2019.08
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Check Bus 2 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus wires and GND when no resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Detection Item Trouble Area
No resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to GND in CAN main wires

·

ECM

·

Central gateway ECU (network gateway ECU)

·

No. 66 junction connector



WIRING DIAGRAM

C400782E04
0.854,0.365 1.469,0.563 0.615,0.198 10 false CA4H 0.885,1.104 1.5,1.302 0.615,0.198 10 false CA4L 0.167,1.427 0.781,1.625 0.615,0.198 10 false J51 0.146,1.604 1.646,1.99 1.5,0.385 10 false Central Gateway ECU (Network Gateway ECU) 2.563,1.375 3.177,1.573 0.615,0.198 10 false A85 2.563,1.531 4.292,1.771 1.729,0.24 10 false No. 66 Junction Connector 5.958,0.375 6.573,0.573 0.615,0.198 10 false CANH 5.969,1.083 6.583,1.281 0.615,0.198 10 false CANL 1.854,2.458 2.99,2.646 1.135,0.188 10 false *1: for N04C-UH 3.094,2.448 4.875,2.635 1.781,0.188 10 false *2: for N04C-VQ, N04C-VL 4.896,2.438 6.135,2.646 1.24,0.208 10 false *3: for 2TR-FE 4.865,0.271 5.479,0.469 0.615,0.198 10 false 17*1 5.271,0.281 5.885,0.479 0.615,0.198 10 false 7*2 5.583,0.281 6.198,0.479 0.615,0.198 10 false 33*3 5.604,0.813 6.219,1.01 0.615,0.198 10 false 34*3 5.26,0.813 5.875,1.01 0.615,0.198 10 false 1*2 4.865,0.813 5.479,1.01 0.615,0.198 10 false 28*1 6.26,1.406 6.719,1.604 0.458,0.198 10 false ECM 4.896,0.479 5.354,0.677 0.458,0.198 10 false A52 4.885,1 5.344,1.198 0.458,0.198 10 false A52 5.25,0.469 5.708,0.667 0.458,0.198 10 false A56 5.625,0.469 6.083,0.667 0.458,0.198 10 false A53 5.625,1 6.083,1.198 0.458,0.198 10 false A53 5.25,1 5.708,1.198 0.458,0.198 10 false A56 1.323,0.375 1.635,0.573 0.313,0.198 10 false 18 1.333,0.906 1.646,1.104 0.313,0.198 10 false 17 3.24,0.375 3.552,0.573 0.313,0.198 10 false 3 3.177,0.917 3.49,1.115 0.313,0.198 10 false 14 3.833,0.385 4.146,0.583 0.313,0.198 10 false 1 3.823,0.917 4.135,1.115 0.313,0.198 10 false 12

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 66 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 66 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C358918E02
1.552,0.156 1.906,0.427 0.354,0.271 5.156,0.135 5.51,0.406 0.354,0.271 1.438,0.969 1.146,0.49 1.146,0.49 0.979,0.49 true 1.208,0.969 0.854,0.781 0.854,0.781 0.677,0.781 true 1.188,1.188 0.885,1.427 0.885,1.427 0.729,1.427 true 1.438,1.167 1.302,1.635 1.302,1.635 1.135,1.635 true 5.323,0.802 5.521,1.531 5.521,1.531 5.677,1.531 true 0.396,0.396 1.313,0.594 0.917,0.198 10 false CANH*d 0.115,0.698 1.031,0.896 0.917,0.198 10 false CANH*c 0.188,1.333 1.104,1.531 0.917,0.198 10 false CANL*c 0.604,1.552 1.521,1.75 0.917,0.198 10 false CANL*d 5.729,1.458 6.25,1.677 0.521,0.219 10 false CG 5.229,0.188 6.146,0.385 0.917,0.198 10 false J45 1.615,0.208 2.531,0.406 0.917,0.198 10 false A85 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 4.156,0.115 4.469,0.313 0.313,0.198 10 false *b

Text in Illustration
*a Front view of wire harness connector
(to No. 66 Junction Connector)
*b Front view of DLC3
*c to ECM *d to Central Gateway ECU (Network Gateway ECU)

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
A85-1 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher ECM
A85-12 (CANL) - J45-4 (CG)
A85-3 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
A85-14 (CANL) - J45-4 (CG)



Result:
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (ECU or sensor CAN main wires) C



A

REPLACE NO. 66 JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 66 JUNCTION CONNECTOR)

C

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 66 JUNCTION CONNECTOR)
a.

Reconnect the A85 No. 66 junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C338146E36
0.146,3.229 0.49,3.51 0.344,0.281 1.49,0.354 1.833,0.635 0.344,0.281 2.031,2.458 1.865,2.458 1.865,2.458 1.656,1.521 true 2.073,4.24 1.917,4.24 1.917,4.24 1.635,3.323 true 2.125,2.177 1.958,2.177 1.958,2.177 1.792,1.531 true 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 0.125,2.542 0.438,2.74 0.313,0.198 10 false *b 1.552,0.417 1.948,0.615 0.396,0.198 10 false J51 0.208,3.281 0.604,3.479 0.396,0.198 10 false J45 2.115,2.385 2.729,2.583 0.615,0.198 10 false CA4L 2.198,2.094 2.813,2.292 0.615,0.198 10 false CA4H 2.156,4.156 2.771,4.354 0.615,0.198 10 false CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-18 (CA4H) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-17 (CA4L) - J45-4 (CG)


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 66 JUNCTION CONNECTOR)

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.
C334464E29
1.469,0.271 1.865,0.521 0.396,0.25 1.458,2.406 1.854,2.656 0.396,0.25 2.146,1.979 1.99,1.979 1.99,1.979 1.677,1.156 true 2.448,1.698 2.302,1.698 2.302,1.698 1.76,1.156 true 2,4.063 1.844,4.063 1.844,4.063 1.625,3.25 true 1.563,0.313 2.021,0.51 0.458,0.198 10 false J51 1.542,2.448 2,2.646 0.458,0.198 10 false J45 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 0.146,2.271 0.604,2.469 0.458,0.198 10 false *b 2.531,1.625 2.99,1.823 0.458,0.198 10 false CA4L 2.219,1.896 2.677,2.094 0.458,0.198 10 false CA4H 2.063,3.99 2.521,4.188 0.458,0.198 10 false CG

Reconnect the A85 No. 66 junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-18 (CA4H) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-17 (CA4L) - J45-4 (CG)


Text in Illustration
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3

HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BUS WIRES OR CONNECTOR