There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
| Detection Item | Trouble Area |
|---|---|
|
*1: for LHD *2: for RHD |
|
| No resistance exists between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3. | ·
Short to +B in CAN main wires ·
Central gateway ECU (network gateway ECU) ·
Combination meter assembly ·
No. 59 junction connector*1 ·
No. 68 junction connector*2 |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and DTC may be stored.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 59 junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 59 Junction Connector) |
*b | Front view of DLC3 |
| *c | to Central Gateway ECU (Network Gateway ECU) | *d | to Combination Meter Assembly |
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| J86-8 (CANH) - J45-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| J86-5 (CANL) - J45-16 (BAT) | |||
| J86-9 (CANH) - J45-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Combination meter assembly |
| J86-6 (CANL) - J45-16 (BAT) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Central gateway ECU CAN main wire) | B |
| NG (ECU or sensor CAN main wires) | C |
A
B
C
Reconnect the J86 No. 59 junction connector.
Disconnect the central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J51-15 (CA5H) - J45-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| J51-16 (CA5L) - J45-16 (BAT) |
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the J86 No. 59 junction connector.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J51-15 (CA5H) - J45-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| J51-16 (CA5L) - J45-16 (BAT) |
| *a | Component with harness connected
(Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 68 junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 68 Junction Connector) |
*b | Front view of DLC3 |
| *c | to Central Gateway ECU (Network Gateway ECU) | *d | to Combination Meter Assembly |
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| J76-5 (CANH) - J45-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| J76-16 (CANL) - J45-16 (BAT) | |||
| J76-6 (CANH) - J45-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Combination meter assembly |
| J76-17 (CANL) - J45-16 (BAT) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Central gateway ECU CAN main wire) | B |
| NG (ECU or sensor CAN main wires) | C |
A
B
C
Reconnect the J76 No. 68 junction connector.
Disconnect the central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J51-15 (CA5H) - J45-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| J51-16 (CA5L) - J45-16 (BAT) |
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the J76 No. 68 junction connector.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J51-15 (CA5H) - J45-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| J51-16 (CA5L) - J45-16 (BAT) |
| *a | Component with harness connected
(Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG