Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2017.01–2019.08
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Check Bus 5 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus wires and GND when no resistance exists between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Detection Item Trouble Area

*1: for LHD

*2: for RHD

No resistance exists between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to GND in CAN main wires

·

Central gateway ECU (network gateway ECU)

·

Combination meter assembly

·

No. 59 junction connector*1

·

No. 68 junction connector*2



WIRING DIAGRAM

C371311E07
0.823,0.365 1.438,0.563 0.615,0.198 10 false CA5H 0.865,1.094 1.479,1.292 0.615,0.198 10 false CA5L 5.948,0.385 6.563,0.583 0.615,0.198 10 false CANH 5.958,1.073 6.573,1.271 0.615,0.198 10 false CANL 2.833,0.365 4.063,0.563 1.229,0.198 10 false 8*1, 5*2 2.781,0.917 4.01,1.115 1.229,0.198 10 false 5*1, 16*2 3.823,0.375 5.052,0.573 1.229,0.198 10 false 9*1, 6*2 3.833,0.906 5.063,1.104 1.229,0.198 10 false 6*1, 17*2 0.188,1.438 1.417,1.635 1.229,0.198 10 false J51 0.167,1.635 1.688,2.01 1.521,0.375 10 false Central Gateway ECU (Network Gateway ECU) 0.146,2.406 1.375,2.604 1.229,0.198 10 false *1: for LHD 1.219,2.406 2.448,2.604 1.229,0.198 10 false *2: for RHD 2.604,1.385 3.833,1.583 1.229,0.198 10 false J86*1, J76*2 2.594,1.573 4.375,1.927 1.781,0.354 10 false No. 59 Junction Connector*1, No. 68 Junction Connector*2 5.594,1.354 6.823,1.552 1.229,0.198 10 false J1 5.594,1.542 6.771,1.885 1.177,0.344 10 false Combination Meter Assembly 1.313,0.375 1.625,0.573 0.313,0.198 10 false 15 1.323,0.906 1.635,1.104 0.313,0.198 10 false 16 5.708,0.375 6.021,0.573 0.313,0.198 10 false 23 5.719,0.917 6.031,1.115 0.313,0.198 10 false 22

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and DTC may be stored.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 59 JUNCTION CONNECTOR)

B

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 68 JUNCTION CONNECTOR)
2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 59 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 59 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C358918E06
0.302,0.875 0.656,1.146 0.354,0.271 5.156,0.135 5.51,0.406 0.354,0.271 2.115,0.948 2.115,0.458 2.115,0.458 2.281,0.458 true 2,0.927 2,0.24 2,0.24 2.188,0.24 true 1.667,0.958 1.667,0.458 1.667,0.458 1.51,0.458 true 1.781,0.948 1.781,0.25 1.781,0.25 1.615,0.25 true 5.323,0.813 5.521,1.51 5.521,1.51 5.719,1.51 true 2.354,0.396 3.271,0.594 0.917,0.198 10 false CANH*d 2.25,0.156 3.167,0.354 0.917,0.198 10 false CANH*c 0.979,0.375 1.896,0.573 0.917,0.198 10 false CANL*c 1.083,0.156 2,0.354 0.917,0.198 10 false CANL*d 5.802,1.427 6.323,1.646 0.521,0.219 10 false CG 5.229,0.188 6.146,0.385 0.917,0.198 10 false J45 0.354,0.917 1.271,1.115 0.917,0.198 10 false J86 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 4.156,0.115 4.469,0.313 0.313,0.198 10 false *b

Text in Illustration
*a Front view of wire harness connector
(to No. 59 Junction Connector)
*b Front view of DLC3
*c to Central Gateway ECU (Network Gateway ECU) *d to Combination Meter Assembly

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
J86-8 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
J86-5 (CANL) - J45-4 (CG)
J86-9 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Combination meter assembly
J86-6 (CANL) - J45-4 (CG)



Result:
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (ECU or sensor CAN main wires) C



A

REPLACE NO. 59 JUNCTION CONNECTOR

B

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 59 JUNCTION CONNECTOR)

C

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 59 JUNCTION CONNECTOR)
a.

Reconnect the J86 No. 59 junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C338146E45
0.156,3.417 0.531,3.729 0.375,0.313 1.51,0.24 1.885,0.552 0.375,0.313 1.75,2.292 1.615,2.292 1.615,2.292 1.365,1.521 true 1.948,2.063 1.802,2.063 1.802,2.063 1.521,1.51 true 1.208,2.698 1.365,2.698 1.365,2.698 1.615,3.146 true 2.021,1.979 2.635,2.177 0.615,0.198 10 false CA5L 1.823,2.219 2.438,2.417 0.615,0.198 10 false CA5H 0.938,2.615 1.385,2.813 0.448,0.198 10 false CG 0.229,3.479 0.844,3.677 0.615,0.198 10 false J45 1.583,0.302 2.198,0.5 0.615,0.198 10 false J51 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.104,2.573 0.417,2.771 0.313,0.198 10 false *b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-15 (CA5H) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-16 (CA5L) - J45-4 (CG)


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 59 JUNCTION CONNECTOR)

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.
C334464E34
1.469,0.271 1.865,0.521 0.396,0.25 0.219,3.417 0.615,3.667 0.396,0.25 2.146,1.979 1.99,1.979 1.99,1.979 1.833,1.146 true 2.448,1.698 2.302,1.698 2.302,1.698 1.927,1.167 true 1.125,2.688 1.292,2.688 1.292,2.688 1.594,3.073 true 1.563,0.313 2.021,0.51 0.458,0.198 10 false J51 0.302,3.458 0.76,3.656 0.458,0.198 10 false J45 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 0.146,2.271 0.604,2.469 0.458,0.198 10 false *b 2.531,1.625 2.99,1.823 0.458,0.198 10 false CA5H 2.219,1.896 2.677,2.094 0.458,0.198 10 false CA5L 0.844,2.604 1.302,2.802 0.458,0.198 10 false CG

Reconnect the J86 No. 59 junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-15 (CA5H) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-16 (CA5L) - J45-4 (CG)


Text in Illustration
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3

HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BUS WIRES OR CONNECTOR

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 68 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 68 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C358918E07
0.302,0.875 0.656,1.146 0.354,0.271 5.156,0.135 5.51,0.406 0.354,0.271 1.802,1.146 1.885,1.604 1.885,1.604 2.063,1.604 true 1.781,0.958 1.865,0.375 1.865,0.375 2.01,0.375 true 1.667,0.958 1.552,0.375 1.552,0.375 1.385,0.375 true 1.667,1.177 1.583,1.604 1.583,1.604 1.417,1.604 true 5.292,0.792 5.51,1.542 5.51,1.542 5.677,1.542 true 2.073,0.302 2.99,0.5 0.917,0.198 10 false CANH*d 0.802,0.281 1.719,0.479 0.917,0.198 10 false CANH*c 0.854,1.521 1.771,1.719 0.917,0.198 10 false CANL*c 2.146,1.521 3.063,1.719 0.917,0.198 10 false CANL*d 5.781,1.469 6.302,1.688 0.521,0.219 10 false CG 5.229,0.188 6.146,0.385 0.917,0.198 10 false J45 0.365,0.917 1.281,1.115 0.917,0.198 10 false J76 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 4.156,0.115 4.469,0.313 0.313,0.198 10 false *b

Text in Illustration
*a Front view of wire harness connector
(to No. 68 Junction Connector)
*b Front view of DLC3
*c to Central Gateway ECU (Network Gateway ECU) *d to Combination Meter Assembly

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
J76-5 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
J76-16 (CANL) - J45-4 (CG)
J76-6 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Combination meter assembly
J76-17 (CANL) - J45-4 (CG)



Result:
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (ECU or sensor CAN main wires) C



A

REPLACE NO. 68 JUNCTION CONNECTOR

B

6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 68 JUNCTION CONNECTOR)

C

7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 68 JUNCTION CONNECTOR)
a.

Reconnect the J76 No. 68 junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C338146E46
0.156,3.417 0.531,3.729 0.375,0.313 1.51,0.24 1.885,0.552 0.375,0.313 1.75,2.292 1.615,2.292 1.615,2.292 1.365,1.521 true 1.948,2.063 1.802,2.063 1.802,2.063 1.521,1.51 true 1.125,2.656 1.313,2.656 1.313,2.656 1.594,3.135 true 2.021,1.979 2.635,2.177 0.615,0.198 10 false CA5L 1.823,2.219 2.438,2.417 0.615,0.198 10 false CA5H 0.854,2.573 1.302,2.771 0.448,0.198 10 false CG 0.229,3.479 0.844,3.677 0.615,0.198 10 false J45 1.583,0.302 2.198,0.5 0.615,0.198 10 false J51 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.104,2.573 0.417,2.771 0.313,0.198 10 false *b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-15 (CA5H) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-16 (CA5L) - J45-4 (CG)


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 68 JUNCTION CONNECTOR)

7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.
C334464E35
1.469,0.271 1.865,0.521 0.396,0.25 0.24,3.427 0.635,3.677 0.396,0.25 2.146,1.979 1.99,1.979 1.99,1.979 1.833,1.146 true 2.448,1.698 2.302,1.698 2.302,1.698 1.927,1.167 true 1.281,2.615 1.417,2.615 1.417,2.615 1.594,3.104 true 1.563,0.313 2.021,0.51 0.458,0.198 10 false J51 0.313,3.458 0.771,3.656 0.458,0.198 10 false J45 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 0.146,2.271 0.604,2.469 0.458,0.198 10 false *b 2.531,1.625 2.99,1.823 0.458,0.198 10 false CA5H 2.219,1.896 2.677,2.094 0.458,0.198 10 false CA5L 1.01,2.542 1.469,2.74 0.458,0.198 10 false CG

Reconnect the J76 No. 68 junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-15 (CA5H) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-16 (CA5L) - J45-4 (CG)


Text in Illustration
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3

HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BUS WIRES OR CONNECTOR