Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


g.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light / ON or OFF ON: Warning light on
OFF: Warning light off
-
Brake Warning Light Brake warning light / ON or OFF ON: Warning light on
OFF: Warning light off
-
Stop Light SW Stop light switch assembly / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW Parking brake switch assembly / ON or OFF ON: Parking brake applied
OFF: Parking brake released
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch (brake with switch pedal sub-assembly) / ON or OFF ON: Brake pedal depressed beyond the specified point
OFF: Brake pedal not depressed beyond the specified point
-
Gear Position Gear position information / Fail, 1st - 7th, "P, N", 8 - 10th, R or Not R - Not used
Shift Lever Position Shift lever position information / Fail, 1st - 5th, 6th/B, D/M, "P, N" or R - Not used
Shift Information Shift information / ON or OFF - Not used
Inspection Mode Inspection mode / Other or Inspect Inspect: Inspection mode
Other: Normal mode
-
Zero Point of M/C Memorized zero value / Min.: -12.50 MPa, Max.: 12.40 MPa - After master cylinder pressure sensor zero point calibration: 2.44 to 2.46 MPa
Deceleration Sensor Acceleration sensor / Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration: Changes continuously
Zero Point of Decele Memorized zero value / Min.: -25.10 m/s2, Max.: 24.90 m/s2 - -
Deceleration Sensor2 Acceleration sensor 2 / Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration: Changes continuously
Zero Point of Decele2 Memorized zero value / Min.: -25.10 m/s2, Max.: 24.90 m/s2 - -
Yaw Rate Sensor Yaw rate sensor / Min.: -128°/s, Max.: 127°/s Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Zero Point of Yaw Rate Memorized zero value / Min.: -128°, Max.: 127° - After completing zero point calibration: 0°
Steering Angle Sensor Steering angle sensor / Min.: -3276.8°, Max.: 3276.7° Turning left: Increases
Turning right: Decreases
-
Zero Point of Steering Angle Memorized zero value / Min.: -128°, Max.: 127° - After steering angle sensor zero point calibration: 0°
Lateral G Lateral G / Min.: -25.10 m/s2, Max.: 24.90 m/s2 - During turning: Changes in proportion with acceleration
Forward and Rearward G Forward and backward G / Min.: -25.10 m/s2, Max.: 24.90 m/s2 - During acceleration/deceleration: Changes in proportion with acceleration
Yaw Rate Value Yaw rate value / Min.: -128°/s, Max.: 127°/s - During turning: Changes in proportion with yaw
Steering Angle Value Steering angle value / Min.: -3276.8°, Max.: 3276.7° - During steering operation: Changes in proportion with steering wheel rotation
Slip Indicator Light Slip indicator light / ON or OFF ON: Indicator light on
OFF: Indicator light off
-
FR Wheel Speed Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Maximum wheel speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FR Wheel Acceleration Front wheel RH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2 - During deceleration/acceleration: Changes continuously
FL Wheel Acceleration Front wheel LH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2 - During deceleration/acceleration: Changes continuously
RR Wheel Acceleration Rear wheel RH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2 - During deceleration/acceleration: Changes continuously
RL Wheel Acceleration Rear wheel LH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2 - During deceleration/acceleration: Changes continuously
FR Wheel ABS Ctrl Status Front wheel RH ABS control status / ON or OFF ON: During control
OFF: Not during control
-
FL Wheel ABS Ctrl Status Front wheel LH ABS control status / ON or OFF ON: During control
OFF: Not during control
-
RR Wheel ABS Ctrl Status Rear wheel RH ABS control status / ON or OFF ON: During control
OFF: Not during control
-
RL Wheel ABS Ctrl Status Rear wheel LH ABS control status / ON or OFF ON: During control
OFF: Not during control
-
TRC(TRAC) Ctrl Status TRC control status / ON or OFF ON: During control
OFF: Not during control
-
TRC(TRAC) Engine Ctrl Status TRC engine control status / ON or OFF ON: During control
OFF: Not during control
-
TRC(TRAC) Brake Ctrl Status TRC engine control status / ON or OFF ON: During control
OFF: Not during control
-
FR Wheel VSC Ctrl Status Front wheel RH VSC control status / ON or OFF ON: During control
OFF: Not during control
-
FL Wheel VSC Ctrl Status Front wheel LH VSC control status / ON or OFF ON: During control
OFF: Not during control
-
RR Wheel VSC Ctrl Status Rear wheel RH VSC control status / ON or OFF ON: During control
OFF: Not during control
-
RL Wheel VSC Ctrl Status Rear wheel LH VSC control status / ON or OFF ON: During control
OFF: Not during control
-
Engine Revolutions Engine speed / Min.: 0 rpm, Max.: 65535 rpm Engine stopped: 0 rpm When engine speed is constant: No large fluctuations
Real Engine Torque Real engine torque / Min.: -1024.0 Nm, Max.: 1023.0 Nm - -
Accelerator Opening Angle % Percentage of accelerator pedal opening angle / Min.: 0.0%, Max.: 127.5% Accelerator pedal released: 0% During accelerator pedal operation: Changes in proportion with the pedal movement
Solenoid Relay Solenoid relay / ON or OFF ON: Solenoid relay on
OFF: Solenoid relay off
-
ECB Motor Relay Motor relay / ON or OFF ON: Motor relay on
OFF: Motor relay off
ECB: Electronically Controlled Brake
TR(A)C/VSC Solenoid (SM2) Master cut solenoid (SM2) / ON or OFF ON: Operating
OFF: Not operating
-
TR(A)C/VSC Solenoid (SM1) Master cut solenoid (SM1) / ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SFRH) ABS solenoid (SFRH) / ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SFRR) ABS solenoid (SFRR) / ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SFLH) ABS solenoid (SFLH) / ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SFLR) ABS solenoid (SFLR) / ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SRRH) ABS solenoid (SRRH) / ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SRRR) ABS solenoid (SRRR) / ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SRLH) ABS solenoid (SRLH) / ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SRLR) ABS solenoid (SRLR) / ON or OFF ON: Operating
OFF: Not operating
-
FR Speed Open Momentary interruption of front speed sensor RH pulse input to ECU / Error or Normal Normal Error: Momentary interruption
FL Speed Open Momentary interruption of front speed sensor LH pulse input to ECU / Error or Normal Normal Error: Momentary interruption
RR Speed Open Momentary interruption of rear speed sensor RH pulse input to ECU / Error or Normal Normal Error: Momentary interruption
RL Speed Open Momentary interruption of rear speed sensor LH pulse input to ECU / Error or Normal Normal Error: Momentary interruption
EFI Communication Open ECM communication open detection / Error or Normal Normal Error: Momentary interruption
Yaw Rate Open Yaw rate sensor open detection / Error or Normal Normal Error: Momentary interruption
Deceleration Open Acceleration sensor open detection / Error or Normal Normal Error: Momentary interruption
Steering Open Steering angle sensor open detection / Error or Normal Normal Error: Momentary interruption
Master Cylinder Open Master cylinder pressure sensor open detection / Error or Normal Normal Error: Momentary interruption
IG1 Voltage Value IG1 voltage value / Min.: 0.00 V, Max.: 20.00 V Ignition switch ON: 11 to 14 V Changes in proportion to battery voltage
BS1 Voltage Value +BS voltage value / Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to battery voltage
MT Voltage Value Motor voltage value / Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to battery voltage
TRC/VSC Off Mode TRC/VSC off mode / Normal, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode
-
Number of DTC Number of DTCs recorded / Min.: 0, Max.: 255 0 -
FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection / Error or Normal Normal Error: Momentary interruption
FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection / Error or Normal Normal Error: Momentary interruption
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection / Error or Normal Normal Error: Momentary interruption
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection / Error or Normal Normal Error: Momentary interruption
M/C Pressure Sensor Noise Master cylinder pressure sensor noise detection / Error or Normal Normal Error: Momentary interruption
Brake Pedal Switch Open Brake pedal load sensing switch (brake with switch pedal sub-assembly) open detection / Error or Normal Normal Error: Momentary interruption
Yaw Rate Sensor Voltage Open Yaw rate sensor voltage open detection / Error or Normal Normal Error: Momentary interruption
EFI Communication Invalid ECM communication invalid detection / Error or Normal Normal Error: Invalid
Reverse Position Switch Shift lever R position status / ON or OFF ON: Shift lever is in R
OFF: Shift lever is not in R
-
Master Cylinder Pressure Master cylinder pressure sensor pressure / Min.: 0.00 MPa, Max.: 24.48 MPa Brake pedal operated: Proportional to pedal force
Brake pedal released: 0.00 to 1.76 MPa
-
Master Cylinder Sensor Temperature Master cylinder pressure sensor temperature / Min.: -80°C (-112°F), Max.: 175°C (347°F) Displays current master cylinder temperature -
Motor Power Supply Voltage Motor power source voltage / Min.: 0.00 V, Max.: 20.00 V Ignition switch ON: 11 to 14 V Changes in proportion to battery voltage
Solenoid Power Supply Voltage Solenoid power supply voltage / Min.: 0.00 V, Max.: 20.00 V Ignition switch ON: 11 to 14 V Changes in proportion to battery voltage
Solenoid State for ECU Control Solenoid (for ECU control) / ON or OFF ON: Solenoid relay operating
OFF: Solenoid relay not operating
-
Motor State for ECU Control Motor (for ECU control) / ON or OFF ON: Motor relay operating
OFF: Motor relay not operating
-
Operation History of IG OFF while Vehicle is moving History of ignition switch turned off when vehicle is in motion / ON or OFF ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher
OFF: No history
-
Master Cylinder Pressure Sensor Power Supply Open Master cylinder pressure sensor power supply voltage status / Error or Normal Normal Error: Momentary interruption
Solenoid Power Supply Open Solenoid power supply voltage status / Error or Normal Normal Error: Momentary interruption
Motor Power Supply Open Motor power supply voltage status / Error or Normal Normal Error: Momentary interruption
Stop Switch Open Momentary interruption (open circuit) in wire harness between skid control ECU (brake actuator assembly) and stop light switch assembly status / Error or Normal Normal Error: Momentary interruption
Brake Booster Pressure No. 1 Brake booster pressure sensor (vacuum sensor assembly) pressure / 0.0 to 127.5 kPa(abs) Brake pedal depressed several times with ignition switch ON and engine stopped: Approximately 100 kPa
HINT:
·

If the result is not as specified, replace the vacuum sensor assembly.

·

If the elevation is 0 m (0 ft.), the atmospheric pressure should be 101 kPa (758 mmHg, 29.8 in. Hg).

·

The atmospheric pressure decreases 1 kPa (8 mmHg, 0.295 in. Hg) for each 100 m (328 ft.) increase in elevation.

·

The atmospheric pressure varies according to the weather.



Brake Booster Pressure Sensor Open No. 1 brake booster pressure sensor (vacuum sensor assembly) open detection / Error or Normal Normal Error: Momentary interruption
Brake Booster Pressure Sensor "B " Open No. 2 brake booster pressure sensor (vacuum sensor assembly) open detection / Error or Normal Normal Error: Momentary interruption
Brake Booster Pressure "B " No. 2 brake booster pressure sensor (vacuum sensor assembly) pressure / 0.0 to 127.5 kPa(abs) Brake pedal depressed several times with ignition switch ON and engine stopped: Approximately 100 kPa
HINT:
·

If the result is not as specified, replace the vacuum sensor assembly.

·

If the elevation is 0 m (0 ft.), the atmospheric pressure should be 101 kPa (758 mmHg, 29.8 in. Hg).

·

The atmospheric pressure decreases 1 kPa (8 mmHg, 0.295 in. Hg) for each 100 m (328 ft.) increase in elevation.

·

The atmospheric pressure varies according to the weather.






ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


g.

According to the display on the GTS, perform the Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ABS Warning Light ABS warning light Warning light ON/OFF Observe combination meter assembly
Vehicle condition: Vehicle stopped
Brake Warning Light Brake warning light Warning light ON/OFF Observe combination meter assembly
Vehicle condition: Vehicle stopped
Solenoid Relay Solenoid relay Relay ON/OFF Vehicle condition: Vehicle stopped
Motor Relay Motor relay Relay ON/OFF Operating sound of motor can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SRLR) ABS solenoid (SRLR) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SRLH) ABS solenoid (SRLH) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SRRR) ABS solenoid (SRRR) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SRRH) ABS solenoid (SRRH) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SFLR) ABS solenoid (SFLR) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SFLH) ABS solenoid (SFLH) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SFRR) ABS solenoid (SFRR) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SFRH) ABS solenoid (SFRH) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
VSC/TRC Solenoid (SMR) Master cut solenoid (SM2) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
VSC/TRC Solenoid (SMF) Master cut solenoid (SM1) Solenoid ON/OFF Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
TRC(TRAC) OFF Indicator Light TRC OFF indicator light Indicator light ON/OFF Observe combination meter assembly
Vehicle condition: Vehicle stopped
VSC OFF Indicator Light VSC OFF indicator light Indicator light ON/OFF Observe combination meter assembly
Vehicle condition: Vehicle stopped
Slip Indicator Light Slip indicator light Indicator light ON/OFF Observe combination meter assembly
Vehicle condition: Vehicle stopped
ABS Solenoid Selection of multiple holding solenoids (SFRH, SFLH, SRRH and SRLH) and pressure reduction solenoids (SFRR, SFLR, SRRR and SRLR) possible Start/Stop Vehicle condition: Vehicle stopped
VSC/TRC(TRAC) Solenoid Selection of multiple master cut solenoids (SMR (SM2) and SMF (SM1)) possible Start/Stop Vehicle condition: Vehicle stopped