Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) › 2017.01–2018.07
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  TERMINALS OF ECU  


TERMINALS OF ECU


C306841E14
0.219,0.146 0.531,0.344 0.313,0.198 10 false *a

Text in Illustration
*a Component without harness connected
(Skid Control ECU (Brake Actuator Assembly))
- -

Terminal No. (Symbol) Terminal Description
1 (GND2) Pump motor ground
2 - (Not used)
3 - (Not used)
4 - (Not used)
5 - (Not used)
6 - (Not used)
7 (VSM2) No. 2 vacuum booster pressure sensor (vacuum sensor assembly) power supply output
8 - (Not used)
9 (VSG2) No. 2 vacuum booster pressure sensor (vacuum sensor assembly) ground
10 (CANL) CAN communication line L
11 - (Not used)
12 (IG1) ECU power supply input
13 (BM) Motor relay power supply
14 (SP1) Speed signal output for speedometer
15 (RR-) Rear wheel speed RH (-) signal input
16 (RR+) Rear wheel speed RH (+) power supply output
17 (FL-) Front wheel speed LH (-) signal input
18 (FL+) Front wheel speed LH (+) power supply output
19 - (Not used)
20 (VSM) No .1 vacuum booster pressure sensor (vacuum sensor assembly) power supply output
21 (VSG) No. 1 vacuum booster pressure sensor (vacuum sensor assembly) ground
22 (CANH) CAN communication line H
23 (FSW+) Brake pedal load sensing switch (brake with switch pedal sub-assembly) input
24 (TS) Sensor check input
25 (GND1) Skid control ECU (Brake actuator assembly) ground
26 - (Not used)
27 - (Not used)
28 (RL-) Rear wheel speed LH (-) signal input
29 (RL+) Rear wheel speed LH (+) power supply output
30 (FR-) Front wheel speed RH (-) signal input
31 (FR+) Front wheel speed RH (+) power supply output
32 (VSI2) No. 2 vacuum booster pressure sensor (vacuum sensor assembly) input
33 - (Not used)
34 (VSI1) No. 1 vacuum booster pressure sensor (vacuum sensor assembly) input
35 (STP) Stop light switch assembly input
36 - (Not used)
37 - (Not used)
38 (+BS) Solenoid relay power supply


TERMINAL INSPECTION


a.

Disconnect the A71 connector and measure the voltage or resistance on the wire harness side.

C306842E08
1.615,1.115 2.094,1.375 0.479,0.26 0.25,0.156 0.563,0.354 0.313,0.198 10 false *a 1.729,1.167 2.167,1.375 0.438,0.208 10 false A71

Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
- -

HINT:

Voltage cannot be measured with the connector connected to the skid control (brake actuator assembly) as the connector is watertight.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A71-1 (GND2) - Body ground W-B - Body ground Pump motor ground Always Below 1 Ω
A71-12 (IG1) - Body ground B - Body ground ECU power supply input Ignition switch ON 11 to 14 V
A71-13 (BM) - Body ground G - Body ground Motor relay power supply Always 11 to 14 V
A71-14 (SP1) - Body ground P - Body ground Speed signal output for speedometer Ignition switch ON 11 to 14 V
A71-23 (FSW+) - Body ground P - Body ground Brake pedal load sensing switch (brake with switch pedal sub-assembly) input Brake pedal depressed → released 950 to 1050 Ω → 203 to 223 Ω
A71-25 (GND1) - Body ground W-B - Body ground Skid control ECU (Brake actuator assembly) ground Always Below 1 Ω
A71-35 (STP) - Body ground BE - Body ground Stop light switch assembly input Stop light switch assembly on → off (Brake pedal depressed → released) 8 to 14 V → Below 1.5 V
A71-38 (+BS) - Body ground GR - Body ground Solenoid relay power supply Always 11 to 14 V