Home › Engine / Hybrid System › 2TR-FE FUEL › FUEL SYSTEM
RM2850E _51 Engine / Hybrid System _073289 2TR-FE FUEL _0356960 FUEL SYSTEM G

2TR-FE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PRESSURE

a.

Check that the battery voltage is above 12 V.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the fuel hose from the fuel filter assembly.


d.
A431281E01
2.448,0.417 2.604,0.698 false 1.354,1.844 1.552,1.594 false 1.031,2.271 1.323,2.24 false 0.885,3.021 1.115,3.354 false 0.958,4.156 1.177,3.833 false 1.792,4.042 1.854,3.667 false 2.01,0.073 2.479,0.469 0.469,0.396 10 false SST Gauge 1.406,1.229 2.24,1.573 0.833,0.344 10 false Fuel Tube Connector 0.354,2.198 1.167,2.542 0.813,0.344 10 false SST Hose 0.333,2.823 1.229,3.094 0.896,0.271 10 false SST Clip 0.198,4.042 1.063,4.26 0.865,0.219 10 true SST T-Joint 1.49,3.469 2.323,3.646 0.833,0.177 10 true Fuel Hose

Install SST (pressure gauge) using SSTs and a fuel tube connector as shown in the illustration.


e.

Wipe off any spilt gasoline.


f.

Reconnect the cable to the negative (-) battery terminal.


g.

Connect the intelligent tester to the DLC3 (See step 1 in check fuel pump operation).


h.

Measure the fuel pressure.

Fuel pressure:

281 to 287 kPa (2.87 to 2.93 kgf/cm2, 40.8 to 41.7 psi)


If the pressure is high, replace the fuel pressure regulator.

If the pressure is low, check the fuel hoses, fuel hose connection, fuel pump, fuel filter and fuel pressure regulator.


i.

Disconnect the intelligent tester from the DLC3.


j.

Stop the engine.


k.

Measure the fuel pressure at idle.

Fuel pressure:

281 to 287 kPa (2.87 to 2.93 kgf/cm2, 40.8 to 41.7 psi)


If the pressure is not as specified, check the vacuum sensing hose and fuel pressure regulator.


l.

Stop the engine.


m.

Check that the fuel pressure remains as specified for 5 minutes after the engine has stopped.

Fuel pressure:

147 kPa (1.5 kgf/cm2, 21 psi) or higher


If the pressure is not as specified, check the fuel pump, pressure regulator and/or injector.


n.

After checking fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove the SST to prevent gasoline spillage.


o.

Connect the fuel hose to the fuel filter assembly.


p.

Reconnect the cable to the negative (-) battery terminal.


q.

Check for fuel leakage.


Hide 2.CHECK FUEL PUMP OPERATION AND FUEL LEAK

a.

When using an intelligent tester:

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch ON and the intelligent tester main switch on.

NOTICE:

Do not start the engine.



iii.

Select the Active Test mode on the intelligent tester.

HINT:

Refer to the intelligent tester operator's manual for further details.




b.

Check that there is no fuel leakage anywhere in the fuel system after doing maintenance.