Home › Engine / Hybrid System › N04C-VL EXHAUST › EXHAUST PIPE
RM2850E _51 Engine / Hybrid System _073302 N04C-VL EXHAUST _0356968 EXHAUST PIPE A

N04C-VL EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install a new gasket.

NOTICE:

Do not reuse the removed gasket.



b.

Temporarily install the front exhaust pipe assembly with 3 new nuts.


c.

Install the bolt.

Torque:

28 N*m (282 kgf*cm, 20 ft.*lbf)



d.

Tighten the 3 nuts.

Torque:

62 N*m (632 kgf*cm, 46 ft.*lbf)



Hide 17420 2.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.

Install 2 new gaskets.

NOTICE:

Do not reuse the removed gasket.



b.

Temporarily install the center exhaust pipe assembly with 2 new nuts.


c.

Install the exhaust retarder assembly and the center exhaust pipe assembly with the 4 bolts.

Torque:

27 N*m (275 kgf*cm, 20 ft.*lbf)



d.

Tighten the 2 nuts.

Torque:

19 N*m (194 kgf*cm, 14 ft.*lbf)



Hide 44773D 3.CONNECT SOLENOID TO RETARDER HOSE

a.

Connect the solenoid to retarder hose.


Hide 17420K 4.INSTALL NO. 2 CENTER EXHAUST PIPE ASSEMBLY

a.
A104634

Inspect the compression spring.

i.

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

40.0 mm (1.57 in.)


If the free length is less than the minimum, replace the compression spring.



b.

Install a new gasket.

NOTICE:
·

Install the gasket in the correct direction.

·

Do not damage the outer surface of the gasket.

·

Do not reuse the removed gasket.

·

Do not push in the gasket with the No. 2 center exhaust pipe assembly when connecting it.




c.

Install the No. 2 center exhaust pipe assembly with 4 new nuts.

Torque:

19 N*m (194 kgf*cm, 14 ft.*lbf)



d.

Install the 2 compression springs and the 2 through bolts.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf)



Hide 5.INSTALL FORKED EXHAUST PIPE SUB-ASSEMBLY (for Rear Exhaust Type)

a.

Install a new gasket.

NOTICE:

Do not reuse the removed gasket.



b.

Install the bolt.

Torque:

23 N*m (230 kgf*cm, 17 ft.*lbf)



c.

Install the 2 new nuts.

Torque:

7.0 N*m (70 kgf*cm, 61 in.*lbf)



d.

Install the 2 bolts and 2 new nuts.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf)



Hide 17430 6.INSTALL TAIL EXHAUST PIPE ASSEMBLY (for Rear Exhaust Type)

a.

Install a new gasket.

NOTICE:

Do not reuse the removed gasket.



b.

Temporarily install the tail exhaust pipe assembly with 2 bolts and 2 new nuts.


c.

Install the bolt.

Torque:

23 N*m (230 kgf*cm, 17 ft.*lbf)



d.

Tighten the 2 bolts and 2 new nuts.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf)



Hide 17430 7.INSTALL TAIL EXHAUST PIPE ASSEMBLY (for Side Exhaust Type)

a.

Install a new gasket.

NOTICE:

Do not reuse the removed gasket.



b.

Temporarily install the tail exhaust pipe assembly with 2 new nuts and the 2 bolts.


c.

Install the bolt.

Torque:

23 N*m (230 kgf*cm, 17 ft.*lbf)



d.

Tighten the 2 new nuts and the 2 bolts.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf)



Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:

3.9 N*m (40 kgf*cm, 35 in.*lbf)


Hide 9.INSTALL EXHAUST GAS LEAK