Home › Engine / Hybrid System › 2TR-FE IGNITION › IGNITION SYSTEM
RM2850E _51 Engine / Hybrid System _073297 2TR-FE IGNITION _0357004 IGNITION SYSTEM G

2TR-FE IGNITION  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

HINT:

In this section, the terms Cold and Hot refer to the temperature of the coils. Cold means approximately -10 to 50 °C (14 to 122 °F). Hot means approximately 50 to 100 °C (122 to 212 °F).


PROCEDURE

Hide 1.INSPECT INSPECT IGNITION COIL AND SPARK TEST

a.

Check for DTCs.

NOTICE:

If a DTC is present, perform troubleshooting in accordance with the procedure for that DTC.



b.

Check whether sparks occur.

i.

Remove the engine service hole main cover.


ii.

Remove the rear engine service cover weatherstrip.


iii.

Remove the engine service hole cover mat.


iv.

Remove the No. 2 engine service hole cover sub-assembly.


v.

Remove the shift and select lever support with boots.


vi.

Remove the floor shift lever assembly.


vii.

Remove the front engine service cover panel sub-assembly.


viii.

Remove the 4 ignition coils.


ix.

Using a 16 mm (0.63 in) plug wrench, remove the 4 spark plugs.


x.

Reinstall a spark plug into each ignition coil and connect the ignition coil connector.


xi.

Disconnect the 4 injector connectors.


xii.

Ground the spark plug.


xiii.

Check that sparks occur while the engine is being cranked.

NOTICE:
·

Ground the spark plug when checking.

·

Replace the ignition coil if it has been subjected to a physical impact.

·

Do not crank the engine for more than 2 seconds.


If sparks do not occur, perform the following procedure.




c.

Perform the spark test in accordance with the following procedure.

i.

Check that the ignition coil wire harness connector is securely connected.

Result:
Result Proceed to
NG Connect securely
OK Go to next step



ii.

Perform a spark test on each ignition coil.

1.

Replace the ignition coil with a functioning one.

2.

Perform the spark test again.


Result:
Result Proceed to
OK Replace ignition coil
NG Go to next step



iii.

Check the spark plug.

1.

Replace the spark plug with a normal one.

2.

Perform the spark test again.


Result:
Result Proceed to
OK Replace spark plug
NG Go to next step



iv.

Check the power supply to the ignition coil.

1.

Turn the ignition switch on (IG).

2.

Check that there is battery voltage at the positive (+) ignition coil terminal.


Result:
Result Proceed to
NG Check wiring between ignition switch and ignition coil
OK Go to next step



v.

Check the camshaft position sensor.

Result:
Result Proceed to
NG Replace camshaft position sensor
OK Go to next step



vi.

Check the crankshaft position sensor.

Result:
Result Proceed to
NG Replace crankshaft position sensor
OK Go to next step



vii.

Check the IGT and IGF signal circuits.

Result:
Result Proceed to
NG Check ECM
OK Repair wiring between ignition coil and ECM




d.

Connect the 4 injector connectors.


e.

Using a 16 mm (0.63 in) plug wrench, install the 4 spark plugs.

Torque:

18 N*m (184 kgf*cm, 13 ft.*lbf)



f.

Install the 4 ignition coils.


g.

Install the front engine service cover panel sub-assembly.


h.

Install the floor shift lever assembly.


i.

Install the shift and select lever support with boots.


j.

Install the No. 2 engine service hole cover sub-assembly.


k.

Install the engine service hole cover mat.


l.

Install the rear engine service cover weatherstrip.


m.

Install the engine service hole main cover.


Hide 19100P 2.INSPECT SPARK PLUG

NOTICE:

Do not use a wire brush for cleaning.


a.

Check the electrode.

i.
I039522E65
0.729,1.938 1.094,1.938 false 0.198,1.865 0.708,2.063 0.51,0.198 10 false Ground 1.865,0 2.844,0.177 0.979,0.177 10 false Megohmmeter

Using a megaohmmeter, measure the insulation resistance.

Standard resistance:

10 KΩ or more


HINT:
·

If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.

·

If a megaohmmeter is not available, perform the following simple inspection instead.





b.

Alternative inspection method.

i.

Quickly accelerate the engine to 4000 rpm 5 times.


ii.

Remove the spark plug.


iii.
P003783

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



c.

Check the spark plug for any damage to its thread and insulator.

If there is damage, replace the spark plug.

Recommended spark plug:
Manufacturer Product
DENSO made SK20HR11
NGK made ILFR6C11



d.
A122451E01
2.116,1.548 3.042,1.727 0.926,0.178 10 Electrode Gap

Check the spark plug electrode gap.

Maximum electrode gap for used spark plug:

1.3 mm (0.051 in.)


If the gap is greater than the maximum, replace the spark plug.

Electrode gap for new spark plug:

1.0 to 1.1 mm (0.039 to 0.043 in.)


NOTICE:

Never attempt to adjust the gap.



e.
B062019

Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

Air pressure:

588 kPa (6 kgf/cm2, 85 psi)


Duration:

20 seconds or less


HINT:

Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.