Home › Engine / Hybrid System › 2TR-FE STARTING › STARTER
RM2850E _51 Engine / Hybrid System _073293 2TR-FE STARTING _0357009 STARTER G

2TR-FE STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

NOTICE:

The following tests must each be performed within 3 to 5 seconds to prevent the coil from burning out.


a.
A161092E01
0.47,1.733 1.171,1.884 0.701,0.151 10 Terminal C 1.546,1.062 0.914,1.694 false

Perform the pull-in test.

i.

Remove the nut, then disconnect the field coil lead wire from terminal C.


ii.
A161093E01
2.029,0.283 2.73,0.434 0.701,0.151 10 Terminal C 1.416,0.951 1.983,0.378 false 2.5,0.698 3.255,0.849 0.755,0.151 10 Terminal 50 1.573,1.477 2.483,0.79 false

Connect the battery to the magnetic switch as shown in the illustration. Check that the clutch pinion gear extends.

If the clutch pinion gear does not move, replace the magnet starter switch assembly.



b.

Perform holding test.

i.
A161094E01
2.192,0.433 2.893,0.584 0.701,0.151 10 Terminal C 1.423,0.969 2.159,0.528 false

Disconnect the negative (-) lead from terminal C while sustaining the above condition. Check that the pinion gear remains extended.

If the clutch pinion gear returns inward, replace the magnet starter switch assembly.



c.
A161095

Check the return operation.

i.

Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.



d.
A161092

Perform the operation test without any load.

i.

Connect the field coil lead wire to terminal C.

Torque:

5.9 N*m (60 kgf*cm, 52 in.*lbf)



ii.
A161096E01
1.834,0.058 2.585,0.209 0.751,0.151 10 Terminal 50 0.19,1.494 0.941,1.645 0.751,0.151 10 Terminal 30 1.581,1.23 1.816,0.139 false 1.359,1.356 1.113,1.579 false

Clamp the starter in a vise.


iii.

Connect the battery and ammeter to the starter as shown in the illustration.


iv.

Check that the starter rotates smoothly and steadily with the clutch pinion gear extended. Check that the ammeter indicates the specified current.

Specified current:

90 A or less at 11.5 V




Hide 28160 2.INSPECT STARTER ARMATURE ASSEMBLY

a.
G036820E01
2.367,1.81 2.844,1.951 0.477,0.14 8 Segment 2.027,1.731 2.176,1.88 2.176,1.88 2.347,1.88 false 0.115,0.074 0.804,0.23 0.689,0.156 10 Ohmmeter

Using an ohmmeter, measure the resistance between any 2 segments of the commutator.

If the result is not as specified, replace the starter armature.

Standard resistance:

Below 1 Ω



b.
G036821E01
2.799,0.573 3.31,0.703 0.511,0.13 8 Coil Core 2.143,1.851 2.802,1.982 0.659,0.131 8 Commutator 2.782,0.642 2.725,0.642 2.725,0.642 2.641,1.191 false 2.006,1.782 2.037,1.914 2.037,1.914 2.126,1.914 false 0.197,0.127 0.892,0.271 0.695,0.145 10 Ohmmeter

Using an ohmmeter, check the resistance between the commutator and armature coil core.

Standard resistance:

10 KΩ or higher


If the result is not as specified, replace the starter armature.


c.
P010586

Check the commutator circle runout.

i.

Place the commutator on V-blocks.


ii.

Using a dial indicator, measure the circle runout.

Maximum runout:

0.05 mm (0.002 in.)


If the runout is greater than the maximum, replace the starter armature.



d.
P010587

Using vernier calipers, measure the commutator diameter.

Standard diameter:

30.0 mm (1.181 in.)


Minimum diameter:

29.0 mm (1.141 in.)


If the diameter is less than the minimum, replace the armature.


e.
A102634

Check that the undercut portion between the segments is free of foreign objects and measure its depth.

Standard undercut depth:

0.6 mm (0.024 in.)


Minimum undercut depth:

0.2 mm (0.008 in.)


If the undercut depth is less than the minimum, correct it with a hacksaw blade.


Hide 28120 3.INSPECT STARTER YOKE ASSEMBLY

a.
A074964

Using an ohmmeter, measure the resistance between the terminal C wire and brushes.

If the result is not as specified, replace the starter yoke assembly.

Standard resistance:

Below 1 Ω



Hide 28140 4.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.

Using vernier calipers, measure the brush length.

A431349E01
0.573,0.281 3.177,0.479 2.604,0.198 10 false Brush Holder Side 0.896,2.146 1.583,2.354 0.688,0.208 10 false Length 3.875,0.292 5.052,0.552 1.177,0.26 10 false Starter Yoke Side 5.896,2.073 6.583,2.281 0.688,0.208 10 false Length

Standard length:

15.5 mm (0.610 in.)


Minimum length:

10.0 mm (0.394 in.)


If the length is less than the minimum, replace the brush holder assembly and starter yoke.


b.
ST00019E01
2.444,1.254 2.88,1.608 0.436,0.355 10 Brush Spring 0.774,1.627 1.17,1.782 0.396,0.155 10 Brush

Check the pull scale reading as soon as the brush spring is separated from the brush.

Standard spring load:

17.6 to 23.5 N (1.8 to 2.4 kgf, 4.0 to 5.3 lbf)


Minimum spring load:

11.8 N (1.2 kgf, 2.7 lbf)


If the spring load is less than the minimum, replace the brush holder assembly.


c.
G036824E01
0.15,0.0 0.853,0.15 0.703,0.15 10 Ohmmeter

Using an ohmmeter, measure the resistance between the positive (+) and negative (-) brush holders.

Standard resistance:

10 KΩ or higher


If the result is not as specified, repair or replace the brush holder assembly.


Hide 28011 5.INSPECT STARTER CLUTCH SUB-ASSEMBLY

a.
P010821E13
2.125,0.094 2.479,0.365 0.354,0.271 10 false Free 1.156,0.948 1.521,1.167 0.365,0.219 10 true Lock

Turn the clutch pinion gear clockwise and check that it turns freely. Try to turn the clutch pinion gear counterclockwise and check that it locks.

If necessary, replace the starter clutch.


Hide 28150 6.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.
A161055E03
1.438,1.823 1.615,1.667 false 1.104,0.125 1.344,0.552 false 2.417,0.625 3.104,0.875 0.688,0.25 10 false Ohmmeter 0.365,0.01 1.125,0.219 0.76,0.208 10 true Terminal C 0.667,1.802 1.417,1.948 0.75,0.146 10 false Terminal 50

Using an ohmmeter, measure the resistance between terminals 50 and C.

If the result is not as specified, replace the magnet starter switch assembly.

Standard resistance:

Below 1 Ω



b.
A161056E03
0.062,1.505 0.844,1.659 0.782,0.154 10 Switch Body 1.088,1.838 1.847,1.983 0.759,0.145 10 Terminal 50 2.309,0.602 3.001,0.741 0.692,0.139 10 Ohmmeter 1.547,1.825 1.547,1.668 false 0.439,1.14 0.529,1.481 false

Using an ohmmeter, measure the resistance between terminal 50 and the magnet switch body.

If the result is not as specified, replace the magnet starter switch assembly.

Standard resistance:

Below 2 Ω