Home › Engine / Hybrid System › N04C-VQ (INTAKE) › INTAKE SYSTEM
RM2850E _51 Engine / Hybrid System _073303 N04C-VQ INTAKE _0357027 INTAKE SYSTEM G

N04C-VQ INTAKE  INTAKE SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT INTAKE SYSTEM

a.

Check that there is no air suction or leaks at the points shown in the illustration.

A257921E02
5.75,0.795 5.943,0.984 0.194,0.188 10 *1 6.283,1.138 6.477,1.327 0.194,0.188 10 *2 6.291,4.112 6.485,4.3 0.194,0.188 10 *3 4.418,3.202 4.612,3.391 0.194,0.188 10 *4 3.073,1.459 3.266,1.647 0.194,0.188 10 *5 3.074,2.404 3.268,2.592 0.194,0.188 10 *6 0.306,3.214 0.5,3.403 0.194,0.188 10 *8 3.705,3.381 3.899,3.57 0.194,0.188 10 *7 0.136,3.965 0.33,4.153 0.194,0.188 10 *9 1.448,3.841 1.689,4.029 0.241,0.188 10 *10 5.806,1.276 6.181,1.215 6.181,1.215 6.281,1.215 false 5.725,4.185 6.279,4.185 false 4.597,3.27 4.659,3.27 4.659,3.27 4.859,3.816 false 1.034,3.276 0.487,3.276 false 0.314,4.031 0.622,4.031 false 1.962,3.906 1.674,3.906 false 1.68,4.805 1.908,4.994 0.228,0.188 10 *11 2.341,4.871 1.899,4.871 false

Text in Illustration
*1 Air Cleaner Assembly *2 Mass Air Flow Meter Sub-assembly
*3 PCV Hose Assembly *4 Turbocharger Sub-assembly
*5 Intercooler Assembly *6 EGR Cooler Sub-assembly
*7 Oil Separator Assembly *8 Diesel Throttle Body Assembly
*9 Manifold Absolute Pressure Sensor *10 EGR Valve Assembly
*11 Intake Manifold - -


Hide 2. TURBOCHARGER SUB-ASSEMBLY PRESSURE

a.
A381104E02
1.948,0.49 2.615,0.49 true 0.479,1.104 0.656,1.104 0.656,1.104 0.74,1.292 false 2.667,0.417 2.865,0.604 0.198,0.188 10 true *1 0.188,1.042 0.5,1.229 0.313,0.188 10 true SST

Using a 3-way connector, connect SST (turbocharger pressure gauge) to the hose leading to the intake manifold.

SST
09992-00242  

Text in Illustration
*1 Manifold Absolute Pressure Sensor


b.

Fully apply the parking brake and chock the 4 wheels.


c.

While depressing the clutch pedal, fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (approximately 3600 to 3700 rpm).

Standard pressure (Gauge pressure):

30 to 60 kPa (0.3 to 0.6 kgf/cm2, 4.3 to 8.7 psi)



Hide 3.INSPECT TURBOCHARGER SUB-ASSEMBLY CONTROL ACTUATOR

a.

Check the voltage of the turbocharger sub-assembly control actuator.

i.

Disconnect the turbocharger sub-assembly connector.


ii.

Turn the ignition switch to ON.


iii.
A257916E01
1.148,1.06 0.818,0.465 0.818,0.465 0.666,0.465 false 1.577,1.06 1.907,0.465 1.907,0.465 2.059,0.465 false 0.547,0.373 0.652,0.542 0.105,0.169 10 1 0.111,0.111 0.313,0.28 0.202,0.169 10 *a 2.082,0.373 2.187,0.542 0.105,0.169 10 2

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
1(HLV) - 2(HLG) Ignition switch ON 9 to 14 V


Text in Illustration

If the voltage is not as specified, check the wire harness and connector.

*a Front view of wire harness connector:
(to Turbocharger Sub-assembly)



Hide 4.CHECK WARNING LIGHT

a.

Check that the engine check warning light comes on when the ignition switch is turned to ON, and that it goes off after the engine is started.


b.
A381104E04
1.948,0.49 2.615,0.49 true 0.479,1.104 0.656,1.104 0.656,1.104 0.74,1.292 false 2.667,0.417 2.865,0.604 0.198,0.188 10 true *1 0.188,1.042 0.5,1.229 0.313,0.188 10 true SST

Using a 3-way connector, connect SST (turbocharger pressure gauge) to the hose leading to the intake manifold.

SST
09992-00242  

*1 Manifold Absolute Pressure Sensor


c.

While idling, check that the engine check warning light comes on when turbocharger sub-assembly pressure is applied with the pressure gauge.

Standard pressure (Gauge pressure):

Engine check warning light comes on when the pressure 230 kPa (2.3 kgf/cm2, 33.3 psi) or move is applied.


NOTICE:

After the inspection, clear the diagnosis code.