28371D
1.INSPECT IG1 NO. 3 RELAY (IG1 NO. 3)
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied | 10 kΩ or higher |
| 3 - 5 | Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the IG NO. 3 relay.
28371E
2.INSPECT IG1 NO. 4 RELAY (IG1 NO. 4)
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied | 10 kΩ or higher |
| 3 - 5 | Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the IG NO. 4 relay.
82641
3.INSPECT NO. 2 INTEGRATION RELAY
The C/OPN relay, IG2 relay, EFI relay and A/F HTR relay is built into the No. 2 integration relay.
Before performing the relay inspection for the relay of the No. 2 integration relay, inspect the IG2 NO. 1 fuse, EFI-MAIN fuse and A/F HTR fuse.
Inspect the C/OPN relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2C-1 - 2C-4 | Battery voltage not applied to terminals 2C- 2 and 2C-3 | 10 kΩ or higher |
| Battery voltage applied to terminals 2C-2 and 2C-3 | Below 1 Ω |
| *a | Component without harness connected
(No. 2 Integration Relay) |
If the result is not as specified, replace the No. 2 integration relay.
Inspect the IG2 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2E-1 - 2C-8 | Battery voltage not applied to terminals 2C- 6 and 2C-7 | 10 kΩ or higher |
| Battery voltage applied to terminals 2C-6 and 2C-7 | Below 1 Ω |
| *a | Component without harness connected
(No. 2 Integration Relay) |
If the result is not as specified, replace the No. 2 integration relay.
Inspect the EFI relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2E-1 - 2D-4 | Battery voltage not applied to terminals 2D- 2 and 2D-3 | 10 kΩ or higher |
| Battery voltage applied to terminals 2D-2 and 2D-3 | Below 1 Ω |
| *a | Component without harness connected
(No. 2 Integration Relay) |
If the result is not as specified, replace the No. 2 integration relay.
Inspect the A/F HTR relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2E-1 - 2D-8 | Battery voltage not applied to terminals 2D- 6 and 2D-7 | 10 kΩ or higher |
| Battery voltage applied to terminals 2D-6 and 2D-7 | Below 1 Ω |
| *a | Component without harness connected
(No. 2 Integration Relay) |
If the result is not as specified, replace the No. 2 integration relay.