Home › Engine / Hybrid System › 2TR-FE (ENGINE MECHANICAL) › DRIVE BELT
RM2850E _51 Engine / Hybrid System _073288 2TR-FE ENGINE MECHANICAL _0356951 DRIVE BELT A

2TR-FE ENGINE MECHANICAL  DRIVE BELT  INSTALLATION  


PROCEDURE

Hide 16361A 1.INSTALL FAN AND GENERATOR V BELT

a.
A156670E02
0.823,1.354 1.073,1.354 false 0.156,1.26 0.792,1.573 0.635,0.313 10 false Tensioner 1.656,4.24 1.979,4.563 0.323,0.323 10 true Turn

Install the drive belt onto the pulleys except the drive belt tensioner pulley.


b.

While the turning the belt tensioner clockwise, install the V-ribbed belt.

NOTICE:
·

The back side of the drive belt should face the tensioner pulley.

·

Check that the drive belt is properly set to each pulley.




c.

After the V belt has been installed, check that the tensioner indicator mark is within range A shown in the illustration.

A156768E01
0.133,0.109 1.919,0.472 1.786,0.363 12 When install a new belt: 3.283,0.109 5.131,0.478 1.848,0.369 12 When install a used belt: 2.271,1.65 2.392,1.822 0.121,0.172 10 A 5.574,1.69 5.695,1.861 0.121,0.172 10 A 3.385,0.879 4.802,1.198 1.416,0.319 10 Bracket Side Indicator 3.617,1.248 4.804,1.56 1.187,0.312 10 Arm Side Indicator 5.861,1.453 4.796,0.977 false 4.796,1.348 5.511,1.586 false 0.149,0.879 1.565,1.198 1.416,0.319 10 Bracket Side Indicator 0.38,1.248 1.567,1.56 1.187,0.312 10 Arm Side Indicator 2.625,1.453 1.56,0.977 false 1.56,1.348 2.274,1.586 false


Hide 88310A 2.INSTALL NO. 1 V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT

a.
A156668E02
2.49,1.406 2.75,1.594 0.26,0.188 10 true A 2.438,2.542 2.552,2.708 0.115,0.167 10 false B

Provisionally install the V ribbed belt onto each pulley.


b.

Adjust the V ribbed belt tension.

i.

Adjust the belt tension by turning bolt B.

Standard tension:
Item Standard specification
New belt 647 to 843 N (66 to 86 in., 145 to 190 lb.)
Used belt 323 to 519 N (33 to 53 in., 73 to 117 lb.)


HINT:
·

New belt refers to a belt which has been used on a running engine for less than 5 minutes.

·

Used belt refers to a belt which has been used on a running engine for 5 minutes or more.

·

After installing a new belt, run the engine for about 5 minutes and recheck the belt tension.

·

After installing a belt, check that it fits properly in the ribbed grooves.

·

V ribbed belt tension and deflection should be checked after 2 revolutions of engine cranking.

·

When using a belt tension gauge, confirm its accuracy by using a master gauge first.




ii.

Tighten nut A.

Torque:

47 N*m (475 kgf*cm, 34 ft.*lbf)




c.
A156767E01
0.021,0.0 1.275,0.179 1.254,0.179 10 98 N (10 kgf, 22 lbf)

Check the belt deflection.

i.

Check the belt deflection by pressing on the belt at the points indicated by the arrow marks in the illustration.

Standard tension:
Item Standard specification
New belt 6.6 to 8.6 mm (0.26 to 0.34 in.)
Used belt 9.8 to 13.0 mm (0.39 to 0.51 in.)


HINT:
·

The most appropriate adjusting force is 98 N (10 kgf, 22 lbf).

·

New belt refers to a belt which has been used on a running engine for less than 5 minutes.

·

Used belt refers to a belt which has been used on a running engine for 5 minutes or more.

·

After installing a new belt, run the engine for about 5 minutes and recheck the belt tension.

·

After installing a belt, check that it fits properly in the ribbed grooves.





Hide 51405A 3.INSTALL NO. 1 ENGINE UNDER COVER

a.

Install the No. 1 engine under cover with the 6 bolts.

Torque:

18 N*m (184 kgf*cm, 13 ft.*lbf)