Home › Engine / Hybrid System › 2TR-FE FUEL › FUEL INJECTOR
RM2850E _51 Engine / Hybrid System _073289 2TR-FE FUEL _0356961 FUEL INJECTOR G

2TR-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1. FUEL INJECTOR ASSEMBLY

a.

Check the resistance.

i.

Using an ohmmeter, measure the resistance between the terminals.

Standard resistance:

11.6 to 12.4Ω at 20°C (68°F)


HINT:

If the resistance is not as specified, replace the injector.




b.
A431283E01
2.438,0.542 2.698,0.542 2.698,0.542 2.885,0.844 false 2.458,1.375 2.396,1.177 false 2.198,2.552 1.979,2.552 false 0.552,2 0.552,1.688 false 1.646,2.771 1.458,2.885 false 1.667,1.927 1.24,2.365 false 1.01,2.229 1.219,2.365 1.219,2.365 1.677,2.271 false 1.469,1.51 1.438,1.188 1.438,1.188 1.885,1.281 false 1.667,1.406 1.448,1.198 false 1.469,0.448 2.49,0.646 1.021,0.198 10 false Fuel Tube No.1 2.354,1.396 2.656,1.552 0.302,0.156 10 false SST 1.031,2.406 1.333,2.563 0.302,0.156 10 false SST 1.135,1 1.427,1.156 0.292,0.156 10 false SST 2.24,2.469 2.542,2.656 0.302,0.188 10 false SST 0.104,1.323 0.99,1.635 0.885,0.313 10 false Fuel Pressure Regulator 0.99,2.833 1.469,2.99 0.479,0.156 10 false Injector

Inspect the injector.

NOTICE:

This test involves high-pressure fuel and electricity. Take all precautions regarding safe handling of both the fuel and the electricity. Perform this test in a safe area, and avoid any spark or flame. Do not smoke.


i.
A431285E01
2.833,0.625 2.833,0.646 false 2.833,1.177 2.833,0.635 false 0.552,1.51 0.948,0.479 0.948,0.479 1.531,1.052 false 0.792,0.281 1.094,0.427 0.302,0.146 10 false SST 2.552,1.281 3.208,1.479 0.656,0.198 10 false Fuel Tube

Install SST (tube connector) to SST (hose), then connect the fuel filter.


ii.

Remove the pressure regulator from the delivery pipe.


iii.

Install the O-ring onto the fuel inlet of the pressure regulator.


iv.
A431286E01
0.656,1.271 0.396,1.719 false 2.073,0.594 1.604,0.594 false 3.063,0.729 3.063,0.396 false 2.729,1.021 2.729,0.688 false 0.385,0.5 1.615,0.646 1.229,0.146 10 false Pressure Regulator 2.615,1.031 2.917,1.177 0.302,0.146 10 false SST 2.969,0.771 3.292,0.917 0.323,0.146 10 false SST 0.698,1.052 1.438,1.375 0.74,0.323 10 false Fuel Return Hose

Connect SST (hose) to the fuel inlet of the pressure regulator with another SST (union) and the 2 bolts.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



v.

Install the O-ring onto the injector.


vi.
A431287E01
1.469,0.76 1.104,0.76 false 1.646,0.417 1.906,0.365 1.906,0.365 1.656,0.24 false 1.479,1.073 1.115,1.073 false 1.49,1.896 1.125,1.896 false 2.354,1.583 2.156,1.583 false 1.979,0.302 2.292,0.469 0.313,0.167 10 false SST 2.406,1.49 2.729,1.698 0.323,0.208 10 false SST 0.844,0.677 1.135,0.823 0.292,0.146 10 false SST 0.635,0.979 1.177,1.188 0.542,0.208 10 false O-Ring 0.406,1.802 1.083,1.948 0.677,0.146 10 false Vinyl Tube

Connect SSTs (adaptor and hose) to the injector, and hold the injector and union with SST (clamp).


vii.

Put the injector into a graduated cylinder.

HINT:

Install a suitable vinyl tube into the injector to prevent gasoline spillage.



viii.

Operate the fuel pump


ix.
A431288E01
0.479,0.635 0.781,0.635 false 0.146,0.552 0.438,0.698 0.292,0.146 10 false SST 1.281,1.135 1.771,1.323 0.49,0.188 10 true On/Off

Connect SST (wire) to the injector and the battery for 15 seconds, and measure the injection volume with a graduated cylinder. Test each injector 2 or 3 times.

SST
09842-30080  

Result:
Volume Difference between each injector
71 to 86ml 15ml or less


NOTICE:

Be sure to switch the power on and off at the battery terminal side.


HINT:

If the injection volume is not as specified, replace the injector.




c.

Check for leakage.

i.
A087750

In the condition above, disconnect the tester probes of SST (wire) from the battery and check for fuel leakage from the injector.

Fuel Drop:

1 drop or less in 12 minutes