The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A55-3 (BATT) - B73-3 (E1) | GR - BR | Battery (for measuring battery voltage and for ECM memory) | Always | 11 to 14 V |
| A55-7 (+BM) - B73-3 (E1) | L - BR | Power source of throttle motor | Always | 11 to 14 V |
| A55-9 (IGSW) - B73-3 (E1) | B - BR | Ignition switch | Ignition switch ON | 11 to 14 V |
| A55-1 (+B) - B73-3 (E1) | B - BR | Power source of ECM | Ignition switch ON | 11 to 14 V |
| A55-8 (MREL) - B73-3 (E1) | B - BR | EFI relay | Ignition switch ON | 11 to 14 V |
| B73-18 (VC) - B73-28 (E2) | R - BR | Power source of sensor (specific voltage) | Ignition switch ON | 4.5 to 5.0 V |
| B73-20 (VTA1) - B73-28 (E2) | L - BR | Throttle position sensor (for engine control) | Ignition switch ON, throttle valve fully closed | 0.5 to 1.1 V |
| Ignition switch ON, throttle valve fully open | 3.3 to 4.9 V | |||
| B73-19 (VTA2) - B73-28 (E2) | L - BR | Throttle position sensor (for sensor malfunction detection) | Ignition switch ON, accelerator pedal fully released | 2.1 to 3.1 V |
| Ignition switch ON, accelerator pedal fully depressed | 4.6 to 5.0 V | |||
| A55-18 (VPA) - A55-20 (EPA) | W - L | Accelerator pedal position sensor (for engine control) | Ignition switch ON, accelerator pedal fully released | 0.5 to 1.1 V |
| Ignition switch ON, accelerator pedal fully depressed | 2.5 to 4.6 V | |||
| A55-19 (VPA2) - A55-21 (EPA2) | GR - G | Accelerator pedal position sensor (for sensor malfunction detection) | Ignition switch ON, accelerator pedal fully released | 1.3 to 1.9 V |
| Ignition switch ON, accelerator pedal fully depressed | 3.5 to 5.0 V | |||
| A55-26 (VCPA) - A55-20 (EPA) | G - L | Power source of accelerator pedal position sensor | Ignition switch ON | 4.5 to 5.0 V |
| B75-28 (VG) - B75-30 (E2G) | LG - P | Mass air flow meter sub-assembly | Idling, A/C switch off | 0.5 to 3.0 V |
| B75-29 (THA) - B73-28 (E2) | P - BR | Intake air temperature sensor | Idling, intake air temperature 20°C (68°F) | 0.5 to 3.4 V |
| B73-32 (THW) - B73-28 (E2) | R - BR | Engine coolant temperature sensor | Idling, engine coolant temperature 80°C (176°F) | 0.2 to 1.0 V |
| B75-6 (#10) - B73-7 (E01)
B75-5 (#20) - B73-7 (E01) B75-2 (#30) - B73-7 (E01) B75-1 (#40) - B73-7 (E01) |
L - W-B
G - W-B R - W-B W - W-B |
fuel injector assembly | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation (See waveform 1) | |||
| B73-17 (IGT1) - B73-3 (E1)
B73-16 (IGT2) - B73-3 (E1) B73-15 (IGT3) - B73-3 (E1) B73-14 (IGT4) - B73-3 (E1) |
R - BR
R - BR G - BR G - BR |
Ignition coil with igniter (ignition signal) | Idling | Pulse generation (See waveform 2) |
| B73-23 (IGF1) - B73-3 (E1) | G - BR | Ignition coil with igniter (ignition confirmation signal) | Ignition switch ON | 4.5 to 5.0 V |
| Idling | Pulse generation (See waveform 2) | |||
| B73-26 (G2) - B73-34 (NE-) | R - W | Camshaft position sensor | Idling | Pulse generation (See waveform 3) |
| B73-27 (NE+) - B73-34 (NE-) | B - W | Crankshaft position sensor | Idling | Pulse generation (See waveform 3) |
| A55-25 (FC) - B73-7 (E01) | R - W-B | Fuel pump control | Ignition switch ON | 11 to 14 V |
| B73-21 (A1A+) - B73-3 (E1)*2 | R - BR | Air fuel ratio sensor | Always (Ignition switch ON) | Fixed at 3.3 V |
| B73-31 (A1A-) - B73-3 (E1)*2 | G - BR | Air fuel ratio sensor | Always (Ignition switch ON) | Fixed at 3.3 V |
| B73-1 (HA1A) - B75-7 (E04)*2 | R - W-B | Air fuel ratio sensor heater | Idling | Pulse generation (See waveform 4) |
| Ignition switch ON | 11 to 14 V | |||
| B73-25 (OX1B) - B73-28 (E2)*2 | B - BR | Heated oxygen sensor | Maintain engine speed at 2500 rpm for 2 minutes after warming up sensor | Pulse generation (See waveform 5) |
| B73-2 (HT1B) - B75-4 (E03)*2 | L - W-B | Heated oxygen sensor | Idling | Below 3.0 V |
| Ignition switch ON | 11 to 14 V | |||
| B73-5 (M+) - B75-3 (ME01) | P - W-B | Throttle actuator | Idling | Pulse generation (See waveform 6) |
| B73-4 (M-) - B75-3 (ME01) | L - W-B | Throttle actuator | Idling | Pulse generation (See waveform 7) |
| B73-29 (KNK1) - B73-30 (EKNK) | B - W | Knock sensor | Maintain engine speed at 4000 rpm after warming up engine | Pulse generation (See waveform 8) |
| B73-13 (OC1+) - B73-12 (OC1-) | G - L | Camshaft timing oil control valve assembly | Idling | Pulse generation (See waveform 9) |
| A55-12 (STA) - B73-3 (E1) | G - BR | Starter signal | Ignition switch START | 6.0 V or more |
| B73-10 (ALT) - B73-3 (E1) | L - BR | Generator | Ignition switch ON | 11 to 14 V |
| A53-4 (STP) - B73-3 (E1) | P - BR | Stop light switch | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | Below 1.5 V | |||
| A55-16 (ST1-) - B73-3 (E1) | G - BR | Stop light switch assembly | Ignition switch ON, brake pedal depressed | Below 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |||
| A53-30 (W)*4 - B73-3 (E1) | L - BR | MIL | Idling | 11 to 14 V |
| Ignition switch ON | Below 3.0 V | |||
| A55-15 (ELS1) - B73-3 (E1) | G - BR | Electric load | Taillight switch on | 7.5 to 14 V |
| Taillight switch off | 0 to 1.5 V | |||
| A53-3 (ELS3) - B73-3 (E1) | B - BR | Defogger | Defogger switch ON | 7.5 to 14 V |
| Defogger switch OFF | 0 to 1.5 V | |||
| A53-1 (TACH) - B73-3 (E1) | B - BR | Engine speed | Idling | Pulse generation (See waveform 10) |
| A53-8 (SPD) - B73-3 (E1) | V - BR | Speed signal from combination meter | Driving at 40 km/h (25 mph) | Pulse generation (See waveform 11) |
| A53-17 (TC) - B73-3 (E1) | P - BR | Terminal TC of DLC3 | Ignition switch ON | 11 to 14 V |
| A53-13 (SIL) - B73-3 (E1) | R - BR | Terminal SIL of DLC3 | Connect intelligent tester to DLC3 | Pulse generation |
| B75-32 (PSW) - B73-3 (E1) | P - BR | Power steering oil pressure switch | While turning steering wheel | Below 1.5 V |
| B73-25 (VAF) - B73-28 (E2)*1 | P - BR | Variable resistor | Ignition switch ON | 2.0 to 3.5 V |
| A53-33*3(CANH) - B73-3(E1) | B - BR | CAN communication line | Ignition switch ON | Pulse generation (See waveform 12) |
| A53-34*3(CANL) - B73-3(E1) | W - BR | CAN communication line | Ignition switch ON | Pulse generation (See waveform 13) |
*1: w/ Variable Resistor
*2: w/o Variable Resistor
*3: w/ ABS
*4: w/o ABS
Waveform 1
| Item | Content |
|---|---|
| Terminal No. (Symbol) | B75-6 (#10), B75-5 (#20), B75-2 (#30) or B75-1 (#40) - B73-7 (E01) |
| Tool Setting | 20 V/DIV., 20 ms./DIV. |
| Condition | Idling |
The wavelength becomes shorter as engine speed increases.
Waveform 2
| Item | Content |
|---|---|
| Terminal No. (Symbol) | (a) B73-17 (IGT1), B73-16 (IGT2), B73-15 (IGT3) or B73-14 (IGT4) - B73-3 (E1) |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Idling |
| Item | Content |
|---|---|
| Terminal No. (Symbol) | (b) B73-23 (IGF1) - B73-3 (E1) |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Idling |
The wavelength becomes shorter as engine speed increases.
Waveform 3
| Item | Content |
|---|---|
| Terminal No. (Symbol) | (a) B73-26 (G2) - B73-34 (NE-) |
| Tool Setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling |
| Item | Content |
|---|---|
| Terminal No. (Symbol) | (b) B73-27 (NE+) - B73-34 (NE-) |
| Tool Setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling |
The wavelength becomes shorter as engine speed increases.
Waveform 4
| Item | Content |
|---|---|
| Terminal No. (Symbol) | B73-1 (HA1A) - B75-7 (E04) |
| Tool Setting | 5 V/DIV., 10 ms./DIV. |
| Condition | Idling |
The duty ratio varies depending on the engine driving condition.
Waveform 5
| Item | Content |
|---|---|
| Terminal No. (Symbol) | B73-25 (OX1B) - B73-28 (E2) |
| Tool Setting | 200 mV/DIV., 200 ms./DIV. |
| Condition | Maintain engine speed at 2500 rpm for 2 minutes after warming up sensor |
In the Data List, item O2S B1 S2 shows the ECM input values from the rear HO2 sensor (sensor 2).
Waveform 6
| Item | Content |
|---|---|
| Terminal No. (Symbol) | B73-5 (M+) - B75-3 (ME01) |
| Tool Setting | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling |
The duty ratio varies depending on the throttle opening operation.
Waveform 7
| Item | Content |
|---|---|
| Terminal No. (Symbol) | B73-4 (M-) - B75-3 (ME01) |
| Tool Setting | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling |
The duty ratio varies depending on the throttle opening operation.
Waveform 8
| Item | Content |
|---|---|
| Terminal No. (Symbol) | B73-29 (KNK1) - B73-30 (EKNK) |
| Tool Setting | 1 V/DIV., 1 ms./DIV. |
| Condition | Maintain engine speed at 4000 rpm after warming up engine |
The wavelength becomes shorter as engine speed increases.
The waveform and amplitudes displayed differ slightly depending on the vehicle.
Waveform 9
| Item | Content |
|---|---|
| Terminal No. (Symbol) | B73-13 (OC1+) - B73-12 (OC1-) |
| Tool Setting | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling |
WAVEFORM 10
| Item | Content |
|---|---|
| Terminal No. (Symbol) | A53-1 (TACH) - B73-3 (E1) |
| Tool Setting | 5 V/DIV, 10 ms./DIV |
| Condition | Idling |
The wavelength becomes shorter as the engine rpm increases.
Waveform 11
| Item | Content |
|---|---|
| Terminal No. (Symbol) | A53-8 (SPD) - B73-3 (E1) |
| Tool Setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Driving at 20 km/h (12 mph) |
The wavelength becomes shorter as vehicle speed increases.
Waveform 12
| Item | Content |
|---|---|
| Terminal No. (Symbol) | A53-33 (CANH) - B73-3 (E1) |
| Tool Setting | 1 V/DIV., 10 μs./DIV. |
| Condition | Ignition switch ON |
The waveform varies depending on the CAN communication signal.
Waveform 13
| Item | Content |
|---|---|
| Terminal No. (Symbol) | A53-34 (CANL) - B73-3 (E1) |
| Tool Setting | 1 V/DIV., 10 μs./DIV. |
| Condition | Ignition switch ON |
The waveform varies depending on the CAN communication signal.