Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM U

2TR-FE ENGINE CONTROL  SFI SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N, the A/C should be off and all accessory switches should be off.


a.

Warm up the engine.


b.

Turn the ignition switch to OFF.


c.

Connect the GTS to the DLC3.


d.

Turn the Ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.

HINT:

To display the entire Data List, press the pull down menu button next to Primary. Then select All Data.

·

To display the list box, press the pull down menu button next to Primary. Then select a measurement group.

·

When you select a measurement group, the ECU data belonging to that group is displayed.

·

Measurement Group List / Description

-

All Data / All data

-

Primary / -

-

Engine Control / Engine control system related data

-

Ptrl General / -

-

Ptrl AF Control / Air fuel ratio control system related data

-

Ptrl AF O2 Sensor / Air fuel ratio sensor and heated oxygen sensor related data

-

Ptrl Throttle / Gasoline throttle system related data

-

Ptrl Intake Control / Intake control system related data

-

Ptrl Valve Control / Valve control system related data

-

Ptrl Misfire / "Misfire" related data

-

Ptrl Starting / "Difficult to start" related data

-

Ptrl Rough Idle / "Rough idle" related data

-

Ptrl Evaporative / Evaporative system related data

-

Ptrl 2nd Air / Secondary air injection system related data

-

Ptrl CAT Converter / Catalyst converter related data

-

Check Mode / Check mode related data

-

Monitor Status / Monitor status related data

-

Ignition / Ignition system related data

-

Charging Control / Charging control system related data

-

Compression / Data used during "Check the Cylinder Compression" Active Test

-

AT / Automatic transmission system related data

-

Vehicle Information / Vehicle information





g.

According to the display on the GTS, read the Data List.

HINT:

The title used for each group of Data List items in this repair manual does not appear on the GTS. However, the name in parentheses after the title, which is a Measurement Group, does appear on the GTS. When the name shown in parentheses is selected on the GTS, all the Data List items listed for that group will be displayed.


Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Injector (Port) Injection period of No. 1 cylinder/
Min.: 0 ms, Max.: 32.64 ms
Idling: 1 to 3 ms -
IGN Advance Ignition timing advance for No. 1 cylinder/
Min.: -64 deg, Max.: 63.5 deg
Idling: BTDC 0 to 20 deg -
Calculate Load ECM calculated load/
Min.: 0%, Max.: 100%
·

Idling: 10 to 30%

·

Running without load (2500 rpm): 10 to 40%


-
Vehicle Load Vehicle load/
Min.: 0%, Max.: 25700%
Actual vehicle load -
MAF Air flow rate from MAF meter/
Min.: 0 g/s, Max.: 665.35 g/s
·

Idling: 1 to 4 g/s.

·

Running without load (2500 rpm): 4 to 15 g/s.


If value is approximately 0.0 g/s:
·

Mass air flow meter sub-assembly power source circuit is open

·

VG circuit is open or shorted


If value is 271.0 g/s. or more:
E2G circuit is open
Engine Speed Engine speed/
Min.: 0 rpm, Max.: 16,383.75 rpm
Idling: 750 to 850 rpm -
Vehicle Speed Vehicle speed/
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed Speed indicated on speedometer
Coolant Temp Engine coolant temperature/
Min.: -40°C (-40°F)
Max.: 140°C (284°F)
After warming up engine: 80 to 95°C (176 to 203°F)
·

If value is -40°C (-40°F): sensor circuit is open

·

If value is 140°C (284°F): sensor circuit is shorted


Intake Air Intake air temperature/
Min.: -40°C (-40°F)
Max.: 140°C (284°F)
Equivalent to ambient air temperature
·

If value is -40°C (-40°F): sensor circuit is open

·

If value is 140°C (284°F): sensor circuit is shorted


Target Air-Fuel Ratio Air-fuel ratio/
Min.: 0, Max.: 1.999
Idling: 0.8 to 1.2 80 to 90°C (176 to of 194°F) of coolant temperature
Knock Correct Learn Value Correction learning value of knocking/
Min.: -64 deg(CA), Max.: 1,984 deg(CA)
0 to 18.5 deg(CA)
Driving: 70 km/h (44 mph)
Service data
Knock Feedback Value Feedback value of knocking/
Min.: -64 deg(CA), Max.: 1,984 deg(CA)
10 to 0 deg(CA)
Driving: 70 km/h (44 mph)
Service data
Accel Sens. No.1 Volt % Absolute accelerator pedal position No. 1/
Min.: 0%, Max.: 100%
10 to 22%: accelerator pedal is released
52 to 92%: accelerator pedal is fully depressed
-
Accel Sens. No.2 Volt % Absolute accelerator pedal position No. 2/
Min.: 0%, Max.: 100%
24 to 40%: accelerator pedal is released
68 to 95%: accelerator pedal is fully depressed
-
Accel Sensor Out No.1 Accelerator pedal position sensor No. 1 output voltage/
Min.: 0 V, Max.: 4.98 V
·

Accelerator pedal released: 0.5 to 1.1 V

·

Accelerator pedal depressed: 2.6 to 4.5 V


-
Accel Sensor Out No.2 Accelerator pedal position sensor No. 2 output voltage/
Min.: 0 V, Max.: 4.98 V
·

Accelerator pedal released: 1.2 to 2.0 V

·

Accelerator pedal depressed: 3.4 to 4.75 V


-
Accelerator Idle Position Whether or not accelerator pedal position sensor is detecting idle/
ON or OFF
Idling: ON -
Throttle Fully Close Learn Throttle fully closed (learned value)/
Min.: 0 V, Max.: 4.98 V
0.4 to 1.0 V: Accelerator pedal released -
Accel Fully Close #1 (AD) Accelerator fully closed value No. 1 (AD)/
Min.: 0 V, Max.: 4.9804 V
- ETCS service data
Accel Fully Close Learn #1 Accelerator fully closed learning value No. 1 /
Min.: 0 deg, Max.: 124.5 deg
- ETCS service data
Accel Fully Close Learn #2 Accelerator fully closed learning value No. 2 /
Min.: 0 deg, Max.: 124.5 deg
- ETCS service data
Fail Safe Drive Whether or not fail-safe function executed/
ON or OFF
·

ETCS has failed: ON

·

ETCS normal: OFF


ETCS service data
Fail Safe Drive (Main CPU) Whether or not fail-safe function executed/
ON or OFF
·

ETCS has failed: ON

·

ETCS normal: OFF


ETCS service data
ST1 Brake pedal/
ON or OFF
Released: ON
Depressed: OFF
-
System Guard System guard/
ON or OFF
- ETCS service data
Open Side Malfunction Open side malfunction/
ON or OFF
- ETCS service data
Throttle Sensor Volt % Absolute throttle position sensor/
Min.: 0%, Max.: 100%
·

10 to 22%: Throttle fully closed

·

64 to 96%: Throttle fully open


-
Throttle Sensor #2 Volt % Throttle sensor positioning #2/
Min.: 0%, Max.: 100%
·

42 to 62%: Throttle fully closed

·

92 to 100%: Throttle fully open


Calculated value based on VTA2
Throttle Idle Position Whether or not throttle position sensor is detecting idle/
ON or OFF
·

ON: Accelerator pedal released

·

OFF: Accelerator pedal fully depressed


-
Throttle Require Position Throttle requirement position/
Min.: 0 V, Max.: 4.98 V
Idling: 0.5 to 1.1 V -
Throttle Sensor Position* Throttle sensor position/
Min.: 0%, Max.: 100%
ON: Idling -
Throttle Sensor Position #2 Throttle sensor position #2/
Min.: 0%, Max.: 100%
- Calculated value based on VTA2
Throttle Position No. 1 Throttle position sensor No. 1 output voltage/
Min.: 0 V, Max.: 4.98 V
·

0.5 to 1.1 V: Accelerator pedal released

·

3.2 to 4.8 V: Accelerator pedal fully depressed


-
Throttle Position No. 2 Throttle position sensor No. 2 output voltage/
Min.: 0 V, Max.: 4.98 V
·

2.1 to 3.1 V: Accelerator pedal released

·

4.6 to 4.98 V: Accelerator pedal fully depressed


-
Throttle Position Command Throttle position command value/
Min.: 0 V, Max.: 4.9804 V
0.5 to 4.8 V -
Throttle Sens Open Pos #1 Throttle sensor opener position No. 1/
Min.: 0, Max.: 4.9804 V
0.6 to 1.4 V ETCS service data
Throttle Sens Open Pos #2 Throttle sensor opener position No. 2/
Min.: 0, Max.: 4.9804 V
1.7 to 2.5 V ETCS service data
Throttle Sens Open #1 (AD) Throttle sensor position No. 1 output voltage (AD)/
Min.: 0 V, Max.: 4.9804 V
0.5 to 4.8 V -
Throttle Motor Whether throttle motor control permitted/
ON or OFF
·

ON: Ignition switch ON

·

OFF: ETCS has failed


-
Throttle Motor Current Throttle motor current/
Min.: 0 A, Max.: 19.9 A
Idling: 0 to 3.0 A ETCS service data
Throttle Motor DUTY Throttle motor/
Min.: 0%, Max.: 100%
10 to 22%: Idling after engine warmed up ETCS service data
Throttle Motor Duty (Open) Throttle motor duty ratio (open)/
Min.: 0%, Max.: 100%
During idling: 0 to 40% ETCS service data
Throttle Motor Duty (Close) Throttle motor duty ratio (close)/
Min.: 0%, Max.: 100%
During idling: 0 to 40% ETCS service data
O2S B1 S2 Heated oxygen sensor output voltage for bank 1 sensor 2/
Min.: 0 V, Max.: 1.275 V
Driving 70 km/h (44 mph): 0.1 to 0.9 V Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
AFS Voltage B1S1 A/F sensor output voltage for bank 1 sensor 1/
Min.: 0 V, Max.: 7.99 V
2.8 to 3.8 V: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
AFS Current B1S1 A/F sensor output current for bank 1 sensor 1/
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the current output of the sensor.
Short FT B1 S1 Short-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
-20 to 20% Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT B1 S1 Long-term fuel term of bank 1/
Min.: -100%, Max.: 99.2%
-20 to 20% Overall fuel compensation carried out in long-term to compensate for continual deviation of short-term fuel trim from central value
Fuel System Status #1 Fuel system status (Bank 1) /
OL, CL, OL Drive, OL Fault or CL Fault
Idling after warming up: CL
·

OL (Open Loop): Has not yet satisfied conditions to go closed loop

·

CL (Closed Loop): Feedback for fuel control.

·

OL Drive: Open loop due to driving conditions (fuel enrichment)

·

OL Fault: Open loop due to detected system fault

·

CL Fault: Closed loop but air fuel ratio sensor which is used for fuel control is malfunctioning


Fuel System Status #2 Fuel system status (Bank 2) /
OL, CL, OL Drive, OL Fault or CL Fault
Unused
·

OL (Open Loop): Has not yet satisfied conditions to go closed loop

·

CL (Closed Loop): Feedback for fuel control.

·

OL Drive: Open loop due to driving conditions (fuel enrichment)

·

OL Fault: Open loop due to detected system fault

·

CL Fault: Closed loop but air fuel ratio sensor which is used for fuel control is malfunctioning


AF Lambda B1 S1 Air-fuel ratio associated with bank 1 sensor 1/
Min.: 0, Max.: 1.99
·

Value less than 1 (0.000 to 0.999) = Rich

·

Stoichiometric air-fuel ratio = 1

·

Value greater than 1 (1.001 to 1.999) = Lean


-
Initial Engine Coolant Temp Initial engine coolant temperature/
Min.: -40°C (40°F), Max.: 120°C (248°F)
Close to ambient temperature Service data
Initial Intake Air Temp Initial intake air temperature/
Min.: -40°C (40°F), Max.: 120°C (248°F)
Close to ambient temperature Service data
Injection Volume (Cylinder 1) Injection volume (cylinder 1)/
Min.: 0 ml, Max.: 2.047 ml
0 to 0.5 ml Quantity of fuel injection volume for 10 times
Starter Signal Starter signal/
ON or OFF
ON: Cranking -
Power Steering Signal Power steering signal/
ON or OFF
ON: Power steering operation -
Power Steer. Sig. Record Power steering signal/
ON or OFF
ON: When steering wheel first turned after ignition switch turned to ON This signal status usually ON until ignition switch turned to OFF
Closed Throttle Position SW Closed throttle position switch (idle switch)/
ON or OFF
ON: Throttle valve is closed -
A/C Signal A/C Signal/
ON or OFF
ON: A/C switch is turned ON -
Electrical Load Signal Electrical load signal/
ON or OFF
ON: Headlights or defogger is turned ON -
Stop Light Switch Stop light switch/
ON or OFF
ON: Brake pedal is depressed -
ETCS Actuator Power Whether or not electronic throttle control system power input/
ON or OFF
ON: Idling -
+BM Voltage +BM Voltage
Min.: 0 V, Max.: 19.9 V
Ignition switch ON and system normal: 11 to 14 V ETCS service data
Battery Voltage Battery voltage/
Min.: 0 V, Max.: 65.535 V
Ignition switch ON and system normal: 11 to 14 V -
Actuator Power Supply Actuator power supply/
ON or OFF
Idling: ON ETCS service data
Atmosphere Pressure Atmosphere pressure/
Min.: 0 kPa, Max.: 255 kPa
- -
ACT VSV A/C cut status for Active Test/
ON or OFF
- Active Test support data
Fuel Pump/Speed Status Fuel pump/speed status/
ON or OFF
Idling: ON -
VVT Control Status #1 VVT control status/
ON or OFF
- -
TC and TE1 TC and TE1 terminal of DLC3/
ON or OFF
- -
Engine Speed of Cyl #1 Engine rpm during No. 1 cylinder fuel cut/
Min.: 0 rpm, Max.: 25600 rpm
- Output only when Control the Cylinder #1 Fuel Cut is performed using ACTIVE TEST
Engine Speed of Cyl #2 Engine rpm during No. 2 cylinder fuel cut/
Min.: 0 rpm, Max.: 25600 rpm
- Output only when Control the Cylinder #2 Fuel Cut is performed using ACTIVE TEST
Engine Speed of Cyl #3 Engine rpm during No. 3 cylinder fuel cut/
Min.: 0 rpm, Max.: 25600 rpm
- Output only when Control the Cylinder #3 Fuel Cut is performed using ACTIVE TEST
Engine Speed of Cyl #4 Engine rpm during No. 4 cylinder fuel cut/
Min.: 0 rpm, Max.: 25600 rpm
- Output only when Control the Cylinder #4 Fuel Cut is performed using ACTIVE TEST
Av Engine Speed of All Cyl Average of engine rpm values during fuel cut of No. 1 to No. 4 cylinder/
Min.: 0 rpm, Max.: 25600 rpm
- Output only when ACTIVE TEST is performed
VVT Aim Angle #1 VVT aim angle (bank 1)/
Min.: 0%, Max.: 100%
Idling: 0 to 80% VVT duty signal value during forcible operation
VVT Change Angle #1 VVT change angle/
Min.: 0 DegFR, Max.: 60 DegFR
Idling: 0 DegFR Displacement angle during forcible operation
VVT OCV Duty #1 VVT OCV operation duty/
Min.: 0%, Max.: 100%
Idling: 0 to 100% Requested duty valve for forcible operation
Idle Fuel Cut Fuel cut idle/
ON or OFF
Fuel cut operation: ON Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed is over 2800 rpm
FC TAU Fuel cut TAU: Fuel cut during very light load/
ON or OFF
Fuel cut operation: ON Fuel cut is being performed under very light load to prevent Engine combustion from becoming incomplete
# Codes(Include History) #Codes/
Min.: 0, Max.: 255
- Number of detected DTC
Check Mode Check mode/
ON or OFF
Check mode ON: ON Click here(Click here)
SPD Test Result Check mode result for vehicle speed sensor/
COMPL / INCMPL
- -
OXS1 Test Result Check mode result for HO2 sensor/
COMPL / INCMPL
- -
A/F Test Results #1 Check mode result for A/F sensor/
COMPL / INCMPL
- -
MIL MIL status/
ON or OFF
ON: MIL ON -
MIL ON Run Distance Distance traveled while MIL is activated/
Min.: 0 km, Max.: 65,535 km
Distance after DTC is detected -
Running Time from MIL ON Running time from MIL ON/
Min.: 0 km, Max.: 65,535 km
Equivalent to running time after MIL is turned on -
Engine Run Time Engine run time/
Min.: 0 s, Max.: 65,535 s
Time after engine start Service data
Time after DTC Cleared Time after DTC cleared/
Min.: 0 min, Max.: 65,535 min
Equivalent to time after DTC was erased -
Distance from DTC Cleared Distance from DTC cleared/
Min.: 0 km, Max.: 65,535 km
Equivalent to drive distance after DTCs were erased -
Warm up Cycle Cleared DTC Warm up cycle after DTC cleared/
Min.: 0, Max.: 255
- Number of warm up cycles after DTC is cleared
OBD Requirements E-OBD - -
Number of Emission DTC Number of Emission DTCs - -
Complete parts Monitor Complete parts monitor/
NOT AVL / AVAIL
- -
Model Code Model code - Identifying model code: TRB###
Engine Type Engine type - Identifying engine type: 2TRFE
Cylinder Number Cylinder number/
Min.: 0, Max.: 255
- Identifying cylinder number: 4
Transmission Type Transmission type - Identifying transmission type: MT
Destination Destination - Identifying destination: V or W
Model Year Model year/
Min.: 1900, Max.: 2155
- Identifying model year: 20##
System Identification System identification - Identifying engine system: GASLIN (gasoline engine)

HINT:

If no conditions are specifically stated for "Idling", the A/C switch is OFF and all accessory switches are OFF.

*: Excluding throttle valve opening percentage due to Idle Speed Control (ISC).




PERFORM ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the tester, perform the Active Test.

Tester Display Test Part Control Range Diagnostic Note
Control the Injection Volume Control injection volume
(Engine speed: 3,000 rpm or less)
Min.: -12.5%, Max.: 24.8%
·

All injectors are tested at once

·

Injection volume is gradually changed between -12.5% and 24.8%


Control the Injection Volume for A/F Sensor Change injection volume 12.5% / 0% / 12.5%
·

Perform test at less than 3000 rpm

·

A/F Control enables to check and graph A/F sensor and heated oxygen sensor voltage outputs

·

To conduct test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / User Data / AFS Voltage B1S1 and O2S B1S2


Control the A/C Cut Signal Control A/C cut signal ON or OFF -
Control the Fuel Pump / Speed Control fuel pump ON or OFF Engine is stopped
Connect the TC and TE1 Connect TC and TE1 ON or OFF -
Control the Idle Fuel Cut Prohibit Control idle fuel cut prohibition ON or OFF During idling
Control the ETCS Open/Close Slow Speed Control ETCS opening/closing slow speed Open or Close Test possible when following conditions met:
·

Ignition switch ON

·

Engine is stopped

·

Accelerator pedal is fully depressed


Control the ETCS Open/Close Fast Speed Control ETCS opening/closing fast speed Open or Close Test possible when following conditions met:
·

Ignition switch ON

·

Engine is stopped

·

Accelerator pedal is fully depressed


Control the VVT Linear (Bank 1) Control VVT (Bank 1) Min: -128%, Max: 127%
This value added to present OCV control duty
100 % : Maximum advance
-100 % : Maximum retard
Engine stalls or idles roughly when VVT actuator operated by 100%
·

Vehicle is stopped

·

Engine idling


Control the VVT System (Bank 1) Control VVT system (Bank 1) ON or OFF
·

ON: Rough idle or engine stall

·

OFF: Normal engine speed

·

Vehicle is stopped

·

Engine idling


Control the Select Cylinder Fuel Cut Selected cylinder (cylinder #1 to #6) injector fuel cut #1/#2/#3/#4 ON/OFF This test when the following conditions are met:
·

Vehicle is stopped

·

Engine idling

·

Shift lever is in N.


Control the All Cylinders Fuel Cut Fuel cut for all cylinders ON or OFF This test when the following conditions are met:
·

Vehicle is stopped

·

Engine idling

·

Shift lever is in N.


Check the Cylinder Compression Check cylinder compression pressure ON or OFF Test possible when following conditions met:
·

Ignition switch ON

·

Engine is stopped