Home › Engine / Hybrid System › 2TR-FE (ENGINE MECHANICAL) › ENGINE UNIT
RM2850E _51 Engine / Hybrid System _073288 2TR-FE ENGINE MECHANICAL _0356954 ENGINE UNIT A

2TR-FE ENGINE MECHANICAL  ENGINE UNIT  REPLACEMENT  


PROCEDURE

Hide 11301C 1.REPLACE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL

a.
A097898E04
1.469,0.885 2.417,0.781 false 0.76,1.417 0.552,1.646 0.552,1.646 1.083,1.771 false 2.479,0.688 2.823,0.875 0.344,0.188 10 true *a 0.354,1.563 0.927,1.927 0.573,0.365 10 false *b

Using a screwdriver with its tip taped, pry out the oil seal.


b.
A097921E04
1.115,0.26 1.615,0.677 false 0.698,0.146 1.063,0.333 0.365,0.188 10 false SST

Place the timing chain cover on wooden blocks.


c.

Using SST and hammer, tap in the oil seal until its surface is flush with the timing gear case edge.

SST
09223-50010  

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap the oil seal at an angle.




d.

Apply a light coat of MP grease to a new oil seal lip.


Hide 11381A 2.REPLACE ENGINE REAR OIL SEAL

A097904E02
1.698,1.083 2.063,0.833 true 1.708,1.958 0.792,1.531 0.792,1.531 1.01,1.531 false 2.115,0.75 3.125,0.917 1.01,0.167 10 false Protective Tape 0.115,1.292 0.677,1.656 0.563,0.365 10 false Wooden Block

a.

Place the oil seal retainer on wooden blocks.


b.

Using a screwdriver with its tip taped and a hammer, tap out the oil seal.


c.
G039580E03
2.229,0.677 2.76,0.927 2.76,0.927 2.229,1.302 false 1.167,0.417 0.802,0.365 0.802,0.365 0.906,1.208 false 0.427,0.271 0.74,0.438 0.313,0.167 10 false SST 2.813,0.833 3.125,1 0.313,0.167 10 false SST

Place the oil seal retainer on wooden blocks.


d.

Using SST and hammer, tap in the oil seal until its surface is flush with the oil seal retainer edge.

SST
09223-15030  
09950-70010  (09951-07150)

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap the oil seal at an angle.




e.

Apply a light coat of MP grease to a new oil seal lip.


Hide 11122 3.REPLACE INTAKE VALVE GUIDE BUSH

a.
A087006

Heat the cylinder head to between 80 and 100°C (176 to 212°F).


b.
A097936E03
1.042,1.281 0.458,0.344 0.458,0.344 1.083,0.844 false 0.26,0.135 0.615,0.292 0.354,0.156 10 false SST

Place the cylinder head on wooden blocks.


c.

Using SST and a hammer, tap out the guide bush.

SST
09201-01055  
09950-70010  (09951-07100)


d.
A087011

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard cylinder bore diameter:

10.285 to 10.306 mm (0.4049 to 0.4057 in.)



e.

Select a new guide bush (STD or O/S 0.05).

Bush Size Bush Bore Diameter
Use STD 10.285 to 10.306 mm (0.4049 to 0.4057 in.)
Use O/S 0.05 10.335 to 10.356 mm (0.4069 to 0.4077 in.)

If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4057 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush.

If the bush bore diameter of the cylinder head is greater than 10.356 mm (0.4077 in.), replace the cylinder head.


f.
A087006

Heat the cylinder head to between 80 and 100°C (176 to 212°F).


g.

Place the cylinder head on wooden blocks.


h.
A097938E02
1.99,1.729 2.094,1.854 false 1.094,1.219 0.583,0.406 0.583,0.406 1.135,0.823 false 0.208,0.281 0.583,0.458 0.375,0.177 10 false SST 2.146,1.802 3.094,2 0.948,0.198 10 false Wooden Block

Using SST and a hammer, tap in a new valve guide bush to the specified protrusion height.

SST
09201-01055  
09950-70010  (09951-07100)

Protrusion height:

9.8 to 10.2 mm (0.3858 to 0.4016 in.)



i.

Using a sharp 5.5 mm reamer, ream the valve guide bush to obtain the standard clearance.

Standard oil clearance:

0.025 to 0.060 mm (0.0010 to 0.0023 in.)



Hide 11126 4.REPLACE EXHAUST VALVE GUIDE BUSH

A097937E03
1.781,0.677 2.115,0.292 2.115,0.292 1.917,1.125 false 2.01,0.021 2.344,0.188 0.333,0.167 10 false SST

a.

Heat the cylinder head to between 80 and 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.

Using SST and a hammer, tap out the guide bush.

SST
09201-01055  
09950-70010  (09951-07100)


d.
A087009

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard cylinder bore diameter:

10.285 to 10.306 mm (0.4049 to 0.4057 in.)



e.

Select a new guide bush (STD or O/S 0.05).

Bush Size Bush Bore Diameter
Use STD 10.285 to 10.306 mm (0.4049 to 0.4057 in.)
Use O/S 0.05 10.335 to 10.356 mm (0.4069 to 0.4077 in.)

If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4057 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush.

If the bush bore diameter of the cylinder head is greater than 10.356 mm (0.4077 in.), replace the cylinder head.


f.
A087006

Heat the cylinder head to between 80 and 100°C (176 to 212°F).


g.

Place the cylinder head on the wooden blocks.


h.
A097939E03
1.917,1.083 2.135,0.24 2.135,0.24 1.802,0.667 false 2.115,0.052 2.479,0.24 0.365,0.188 10 false SST

Using SST and a hammer, tap in a new valve guide bush to the specified protrusion height.

SST
09201-01055  
09950-70010  (09951-07100)

Protrusion height:

7.6 to 8.0 mm (0.2992 to 0.3150 in.)



i.

Using a sharp 5.5 mm reamer, ream the valve guide bush to obtain the standard clearance.

Standard oil clearance:

0.030 to 0.065 mm (0.0012 to 0.0026 in.)



Hide 13201A 5.REPLACE CONNECTING ROD SMALL END BUSH

a.
A054717E24
0.75,0.438 1.083,0.604 0.333,0.167 10 false SST

Using SST and a press, press out the bush.

SST
09222-30010  


b.
A054732E23
2.604,1.052 3.25,1.24 0.646,0.188 10 false Oil Hole

Align the oil holes on a new bush and the connecting rod.


c.
A054717E25
0.698,0.417 1.104,0.615 0.406,0.198 10 false SST

Using SST and a press, press in the bush.

SST
09222-30010  


d.
A054733

Using a pin hole grinder, hone the bush to obtain the standard clearance between the bush and piston pin.


e.

Check that the piston pin fits at normal room temperature.

i.

Coat the piston pin with engine oil, and push it into the connecting rod with your thumb.