Home › Engine / Hybrid System › 2TR-FE (ENGINE MECHANICAL) › ENGINE UNIT
RM2850E _51 Engine / Hybrid System _073288 2TR-FE ENGINE MECHANICAL _0356954 ENGINE UNIT A

2TR-FE ENGINE MECHANICAL  ENGINE UNIT  REPAIR  


PROCEDURE

Hide 11131 1.REPAIR INTAKE VALVE SEAT

NOTICE:

Keep the lip free from foreign matter.


a.
A099449E03
2.438,1.229 3.021,1.427 0.583,0.198 10 false Width

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the valve seat.


c.

Check the valve seat according to the following procedures:

i.

If blue appears 360° around the valve face, the valve face is concentric. If not, replace the valve.


ii.

If blue appears 360° around the valve seat, the guide and valve face are concentric. If not, resurface the valve seat.


iii.

Check that the valve seat contact is in the middle of the valve face with the width between 1.0 and 1.4 mm (0.039 and 0.055 in.).



d.
A099450E02
2.969,0.583 3.333,0.75 0.365,0.167 10 false 30° 2.667,1.729 3.156,1.885 0.49,0.156 10 false Width 2.073,0.354 2.469,0.531 0.396,0.177 10 false 45°

If the seating is too high on the valve face, use 30° and 45° cutters to correct the seat.


e.
A099451E02
1.917,0.427 2.25,0.604 0.333,0.177 10 false 60° 2.917,0.469 3.323,0.635 0.406,0.167 10 false 45° 2.729,1.74 3.167,1.917 0.438,0.177 10 false Width

If the seating is too low on the valve face, use 60° and 45° cutters to correct the seat.


f.

Hand-lap the valve and valve seat with an abrasive compound.


g.

Check the valve seating position.


Hide 11135 2.REPAIR EXHAUST VALVE SEAT

NOTICE:

Keep the lip free from foreign matter.


a.
A099449E04
2.51,1.167 3.073,1.333 0.563,0.167 10 false Width

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the valve seat.


c.

Check the valve seat according to the following procedures:

i.

If blue appears 360° around the valve face, the valve face is concentric. If not, replace the valve.


ii.

If blue appears 360° around the valve seat, the guide and valve face are concentric. If not, resurface the valve seat.


iii.

Check that the valve seat contact is in the middle of the valve face with the width between 1.0 and 1.4 mm (0.039 and 0.055 in.).



d.
A099450E03
2.969,0.583 3.333,0.75 0.365,0.167 10 false 30° 2.667,1.729 3.156,1.885 0.49,0.156 10 false Width 2.073,0.354 2.469,0.531 0.396,0.177 10 false 45°

If the seating is too high on the valve face, use 30° and 45° cutters to correct the seat.


e.
A099451E03
1.917,0.427 2.25,0.604 0.333,0.177 10 false 60° 2.917,0.469 3.323,0.635 0.406,0.167 10 false 45° 2.729,1.74 3.167,1.917 0.438,0.177 10 false Width

If the seating is too low on the valve face, use 60° and 45° cutters to correct the seat.


f.

Hand-lab the valve and valve seat with an abrasive compound.


g.

Check the valve seating position.


Hide 3. BORE CYLINDER

HINT:
·

Bore all 4 cylinders for the O/S piston outside diameter.

·

Replace all the piston rings with ones to match the O/S pistons.



a.
A097953E09
2.396,1.667 2.969,1.833 0.573,0.167 10 false Distance

Keep 4 new O/S pistons.

O/S 0.50 piston diameter:

95.441 to 95.451 mm (3.7575 to 3.7579 in.)



b.

Using a micrometer, measure the piston diameter at right angles to the piston center line, the indicated distance from the piston end.

Standard distance:

13.8 mm (0.543 in.)



c.

Calculate how much each cylinder needs to be rebored:

Size to be rebored = P + C - H:

P = Piston diameter

C = Piston clearance: 0.019 to 0.052 mm (0.0007 to 0.0020 in.)

H = Allowance for honing: 0.02 mm (0.0008 in.) or less



d.

Bore and hone the cylinders to calculated dimensions.

Maximum honing:

0.02 mm (0.0008 in.)


NOTICE:

Excess honing will destroy the finished roundness.