Home › Engine / Hybrid System › 2TR-FE (CHARGING) › CHARGING SYSTEM(for 80A Type)
RM2850E _51 Engine / Hybrid System _073308 2TR-FE CHARGING _0357054 CHARGING SYSTEM(for 80A Type) G

2TR-FE CHARGING  CHARGING SYSTEM(for 80A Type)  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:

If the battery is weak or if the engine is difficult to start, recharge the battery and perform inspections again before returning the vehicle to the customer.


PROCEDURE

Hide 1.CHECK BATTERY CONDITION

a.

Check the battery for damage and deformation. If severe damage, deformation or leakage is found, replace the battery.


b.
A149663

Check the volume of electrolyte in each cell (for maintenance-free batteries).

i.

If the electrolyte volume is below the lower line, add distilled water to each cell or replace the battery.



c.
A001259

Check the volume of electrolyte in each cell (for non-maintenance-free batteries).

i.

If the electrolyte volume is below the lower line, add distilled water to each cell. Then, recharge the battery and check the electrolyte specific gravity.

Standard electrolyte specific gravity:

1.25 to 1.29 at 20°C (68°F)


If the result is not as specified, recharge or replace the battery.



d.
A163697

Measure the battery voltage.

i.

If it has been less than 20 minutes since you stopped driving the vehicle or since the engine was stopped, turn the ignition switch and electrical systems (headlight, blower motor, rear defogger etc.) on for 20 seconds. This will remove the surface charge on the battery.


ii.

Turn the ignition switch to OFF.


iii.

Turn the electrical systems off.


iv.

Using a voltmeter, measure the battery voltage between the positive (+) and negative (-) terminals of the battery.

Standard voltage:

12.5 to 12.9 V at 20°C (68°F)


If the result is not as specified, recharge or replace the battery.



Hide 2.CHECK BATTERY TERMINAL AND FUSE

a.

Check that the battery terminals are not loose or corroded.

If the terminals are corroded, clean the terminals.


b.

Measure the resistance of the fuses.

Standard resistance:

Below 1 Ω


If the result is not as specified, replace the fuse.


Hide 3.CHECK DRIVE BELT

a.
A178308E01
1.125,0.15 1.973,0.293 0.847,0.142 10 INCOREECT

Check the belt for wear, cracks and other signs of damage.

If any defect is found, replace the drive belt.

HINT:

If any of the following defects is found, replace the drive belt.

·

The belt is worn out and wire is exposed.

·

The cracks reach the wire in more than one place.

·

The belt has chunks missing from the ribs.




b.
A178309

Check that the belt fits properly in the ribbed grooves.

HINT:

With your hand, confirm that the belt has not slipped out of the grooves on the bottom of the pulley.



Hide 4.VISUALLY CHECK GENERATOR WIRING

a.

Check that the wiring is in good condition.


Hide 5.LISTEN FOR ABNORMAL NOISE FROM GENERATOR

a.

Check that the generator does not emit any abnormal noise while the engine is running.


Hide 6. CHARGE WARNING LIGHT CIRCUIT

a.

Turn the ignition switch ON. Check that the charge warning light turns on.


b.

Start the engine and check that the light turns off. If the light does not operate as specified, troubleshoot the charge warning light circuit.


Hide 7.CHECK CHARGING CIRCUIT WITHOUT LOAD

a.
A163698E01
0.238,0.257 0.821,0.438 0.583,0.182 10 Ammeter 0.97,0.375 1.144,0.467 false 0.037,2.325 0.495,2.506 0.457,0.182 10 Battery 1.95,2.567 2.561,2.748 0.612,0.182 10 Voltmeter 1.912,2.659 1.591,2.518 false 2.319,1.938 2.963,2.119 0.645,0.182 10 Generator 2.118,0.068 3.164,0.41 1.046,0.342 10 Disconnect Wire from Terminal B

Connect a voltmeter and an ammeter to the charging circuit as follows.

HINT:

If a battery/generator tester is available, connect the tester to the charging circuit in accordance with the manufacturer's instructions.


i.

Disconnect the wire from terminal B of the generator and connect it to the negative (-) lead of the ammeter.


ii.

Connect the ammeter positive (+) lead to terminal B of the generator.


iii.

Connect the voltmeter positive (+) lead to positive (+) terminal of the battery.


iv.

Ground the voltmeter negative (-) lead.



b.

Check the charging circuit.

i.

Keep the engine speed at 2000 rpm and check the reading on the ammeter and voltmeter.

Standard current:

10 A or less


Standard voltage:

13.2 to 15.0 V


If the result is not as specified, replace the generator.

HINT:

If the battery is not fully charged, the ammeter reading will sometimes be more than the standard current.




Hide 8.CHECK CHARGING CIRCUIT WITH LOAD

a.

With the engine running at 2000 rpm, turn on the high beam headlights and turn the heater blower switch to the HI position.


b.

Check the reading on the ammeter.

Standard current:

30 A or more


If the ammeter reading is less than the standard current, replace the generator.

HINT:

If the battery is fully charged, the ammeter reading will sometimes be less than the standard current.

In this case, operate the wiper motor and the window defogger to increase the load and then check the charging circuit again.