Home › Engine / Hybrid System › 2TR-FE (CHARGING) › GENERATOR (for 80A Type)
RM2850E _51 Engine / Hybrid System _073308 2TR-FE CHARGING _0357055 GENERATOR(for 80A Type) A

2TR-FE CHARGING  GENERATOR(for 80A Type)  DISASSEMBLY  


PROCEDURE

Hide 27411 1.REMOVE GENERATOR PULLEY

a.
A201414E02
3.031,1.042 3.031,0.427 3.031,0.427 2.927,0.427 true 2.146,0.198 2.74,0.198 true 2.792,1.094 3.354,1.385 0.563,0.292 10 false SST 1-B 1.583,0.115 2.146,0.417 0.563,0.302 10 false SST 1-A 0.354,0.969 0.677,1.26 0.323,0.292 10 false *b 2.438,1.26 2.781,1.552 0.344,0.292 10 false *a

Hold SST 1-B with a torque wrench, and tighten SST 1-A clockwise with the specified torque.

SST
09820-63011  (09820-06010, 09820-06021)

Torque:

39 N*m (400 kgf*cm, 29 ft.*lbf)

Item Part No.
SST 1-A and B 09820-06010
SST 2 09820-06021


NOTICE:

Check that SST is secured to the rotor shaft.


Text in Illustration
*a Turn
*b Hold


b.

Secure the generator in a vise between aluminum plates.


c.
A399904E01
1.594,0.271 1.875,0.271 1.875,0.271 1.927,1.094 false 0.958,2.708 1.698,1.208 true 0.479,0.188 2.115,0.417 1.635,0.229 10 false SST 1-A and 1-B 0.583,2.75 1.167,3 0.583,0.25 10 false SST 2 1.646,2.594 1.979,2.781 0.333,0.188 10 false *b 2.906,2.833 3.083,3.063 0.177,0.229 10 true *a

Place the rotor shaft end into SST 1-A and 1-B.


d.

Fit SST 2 to the generator pulley nut.


e.

Loosen the pulley nut by turning SST 1-A and 1-B as shown in the illustration.

NOTICE:
·

Check that the drive end frame is secured in the vise tightly.

·

Hold SST 2 tightly during the operation.




f.

Remove SST 2 from the generator assembly.

Text in Illustration
*a Turn
*b Hold


g.
A062756E04
2.073,0.135 0.917,0.135 true 0.74,0.323 0.302,0.323 0.302,0.323 0.302,1.729 true 2.167,0.063 2.719,0.219 0.552,0.156 10 false SST 1-A 0.073,1.76 0.677,1.948 0.604,0.188 10 true SST 1-B 0.865,1.24 1.083,1.427 0.219,0.188 10 false *b 2.896,1.438 3.115,1.625 0.219,0.188 10 false *a

While holding SST 1-B, turn SST 1-A and remove SST 1-A and 1-B.


h.

Remove the pulley nut, then remove the generator pulley.

Text in Illustration
*a Turn
*b Hold


Hide 27039 2.REMOVE REAR GENERATOR END COVER

a.
A399905

Remove the 3 bolts and rear generator end cover.


Hide 27387 3.REMOVE TERMINAL INSULATOR

a.

Remove the terminal insulator from the generator coil assembly.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A399906

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A399907

Remove the 4 bolts.


b.
A153383E25
2.073,0.958 2.688,0.688 false 0.656,1.604 1.219,1.906 false 1.271,1.833 1.521,1.979 0.25,0.146 10 false SST 2.813,0.073 3.146,0.25 0.333,0.177 10 false *b 0.531,0.552 0.719,0.708 0.188,0.156 10 false *a 2.729,0.604 2.969,0.76 0.24,0.156 10 false SST

Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)

Text in Illustration
*a Hold
*b Turn


Hide 27444 6.REMOVE GENERATOR BEARING COVER PACKING

a.
A402476

Remove the bearing cover packing.

NOTICE:

If the bearing cover packing breaks, remove broken pieces completely.


HINT:

The bearing cover packing may be installed on the generator rotor assembly.



Hide 27330 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A231554

Remove the generator rotor assembly.

NOTICE:

Do not drop the generator rotor assembly.



b.

Inspect the generator drive end frame bearing.

i.
A399910

Check that the generator drive end frame bearing is not rough or worn.

If necessary, replace the generator drive end frame bearing.



Hide 27310B 8.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A399908

Remove the 4 screws and retainer plate from the generator drive end frame assembly.


b.
A399909E01
2.188,0.417 2.667,0.76 true 3.073,0.25 3.302,0.25 3.302,0.25 2.844,1.073 true 1.896,0.26 2.354,0.458 0.458,0.198 10 false SST 2.76,0.177 3.219,0.375 0.458,0.198 10 false SST

Using SST and a hammer, tap out the generator drive end frame bearing from the generator drive end frame assembly.

SST
09950-70010  (09951-07100)