Home › Engine / Hybrid System › 2TR-FE (CHARGING) › GENERATOR (for 80A Type)
RM2850E _51 Engine / Hybrid System _073308 2TR-FE CHARGING _0357055 GENERATOR(for 80A Type) A

2TR-FE CHARGING  GENERATOR(for 80A Type)  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A399911E01
2.49,0.573 2.896,0.313 true 2.229,0.885 1.844,0.5 true 1.635,0.313 2.094,0.51 0.458,0.198 10 false SST 2.938,0.188 3.396,0.385 0.458,0.198 10 false SST

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-70010  (09951-07100)


b.
A399912E01
2.833,1.125 2.76,0.906 true 2.771,1.573 2.688,1.354 true 2.76,1.125 3.01,1.323 0.25,0.198 10 true *a 2.708,1.594 2.938,1.781 0.229,0.188 10 true *b

Fit the tabs on the retainer plate into the cutouts on the generator drive end frame assembly to install the retainer plate.

Text in Illustration
*a Tab
*b Cutout


c.

Install the retainer plate with the 4 screws.

Torque:

2.3 N*m (23 kgf*cm, 20 in.*lbf)



Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Place the drive end frame on the generator rotor assembly.


b.
A238333

Install the generator rotor assembly to the generator drive end frame assembly.

NOTICE:

Do not drop the generator rotor assembly.



Hide 27444 3.INSTALL GENERATOR BEARING COVER PACKING

NOTICE:

A new generator coil assembly comes with a generator bearing cover packing. Therefore, it is not necessary to install a new generator bearing cover packing when installing a new generator coil assembly.


a.
A402477E01
1.948,0.323 2.458,0.323 true 1.948,1.281 2.458,1.281 true 2.51,0.229 2.823,0.427 0.313,0.198 10 false *a 2.5,1.188 2.813,1.385 0.313,0.198 10 false *b

Install a new generator bearing cover packing to the generator coil assembly.

Text in Illustration
*a Protrusion
*b Groove

NOTICE:

Align the protrusion of the generator bearing cover packing with the groove of the generator coil assembly when installing.



Hide 27360 4.INSTALL GENERATOR COIL ASSEMBLY

a.
A399913E01
0.708,0.448 1.281,0.594 true 2.604,0.542 2.792,0.542 true 0.531,0.333 0.844,0.531 0.313,0.198 10 false *a 2.833,0.448 3.146,0.646 0.313,0.198 10 false *a

Using a 21 mm deep socket wrench and press, slowly press in the generator coil assembly.

Text in Illustration
*a 21 mm Deep Socket Wrench


b.

Install the generator coil assembly with the 4 bolts.

Torque:

5.6 N*m (57 kgf*cm, 50 in.*lbf)



Hide 27370 5.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A113845E13
0.979,0.74 1.375,0.385 1.375,0.385 1.479,0.385 false 1.51,0.313 1.688,0.469 0.177,0.156 10 false *a

While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the brush holder hole.

Text in Illustration
*a Pin


b.
A399914E01
0.625,0.51 1.76,0.771 true 0.427,0.396 0.74,0.594 0.313,0.198 10 false *a

Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

Torque:

1.8 N*m (18 kgf*cm, 16 in.*lbf)



c.

Pull out the pin from the generator brush holder assembly.

Text in Illustration
*a Pin


Hide 27387 6.INSTALL TERMINAL INSULATOR

a.
A399915

Install the terminal insulator to the generator coil assembly.

NOTICE:

Be sure to install the terminal insulator in the correct direction.



Hide 27039 7.INSTALL REAR GENERATOR END COVER

a.

Install the generator rear end cover to the generator coil assembly with the 3 bolts.

Torque:

4.6 N*m (47 kgf*cm, 41 in.*lbf)



Hide 27411 8.INSTALL GENERATOR PULLEY

a.

Install the generator pulley to the rotor shaft by tightening the generator pulley nut by hand.


b.
A201414E02
3.031,1.042 3.031,0.427 3.031,0.427 2.927,0.427 true 2.146,0.198 2.74,0.198 true 2.792,1.094 3.354,1.385 0.563,0.292 10 false SST 1-B 1.583,0.115 2.146,0.417 0.563,0.302 10 false SST 1-A 0.354,0.969 0.677,1.26 0.323,0.292 10 false *b 2.438,1.26 2.781,1.552 0.344,0.292 10 false *a

Hold SST 1-B with a torque wrench, and tighten SST 1-A clockwise with the specified torque.

SST
09820-63011  (09820-06010, 09820-06021)

Item Part No.
SST 1-A and B 09820-06010
SST 2 09820-06021

Torque:

3.9 N*m (398 kgf*cm, 29 in.*lbf)


NOTICE:

Check that SST is secured to the rotor shaft.


Text in Illustration
*a Turn
*b Hold


c.

Secure the generator assembly in a vise between aluminum plates.


d.
A399916E01
1.927,1.094 1.833,0.156 1.833,0.156 1.688,0.156 false 0.74,2.677 1.719,1.198 true 0.615,0.073 1.917,0.302 1.302,0.229 10 false SST 1-A and 1-B 0.479,2.729 1.781,2.958 1.302,0.229 10 false SST2 2.792,2.823 3.042,3 0.25,0.177 10 false *a 1.688,2.594 1.938,2.771 0.25,0.177 10 false *b

Place the rotor shaft end into SST 1-A and 1-B.


e.

Fit SST 2 to the generator pulley nut.


f.

Tighten the pulley nut, then turn SST 1-A as shown in the illustration.

Torque:

133 N*m (1356 kgf*cm, 98 ft.*lbf)


NOTICE:
·

Check that the generator drive end frame assembly is secured in the vise tightly.

·

Hold SST 2 tightly during the operation.




g.

Remove SST 2 from the generator assembly.

Text in Illustration
*a Turn
*b Hold


h.
A062756E04
2.073,0.135 0.917,0.135 true 0.74,0.323 0.302,0.323 0.302,0.323 0.302,1.729 true 2.167,0.063 2.719,0.219 0.552,0.156 10 false SST 1-A 0.073,1.76 0.677,1.948 0.604,0.188 10 true SST 1-B 0.865,1.24 1.083,1.427 0.219,0.188 10 false *b 2.896,1.438 3.115,1.625 0.219,0.188 10 false *a

Turn SST 1-B, and remove SST 1-A and 1-B.


i.

Turn the generator pulley and check that the generator pulley moves smoothly.

Text in Illustration
*a Turn
*b Hold