Home › Engine / Hybrid System › 2TR-FE (CHARGING) › GENERATOR (for 100A Type)
RM2850E _51 Engine / Hybrid System _073308 2TR-FE CHARGING _0357067 GENERATOR(for 100A Type) A

2TR-FE CHARGING  GENERATOR(for 100A Type)  DISASSEMBLY  


PROCEDURE

Hide 27416 1.REMOVE GENERATOR PULLEY CAP

a.
A339215

Using a screwdriver, puncture the center of the generator pulley cap and pry it off.

NOTICE:

Do not reuse the generator pulley cap.



Hide 27415 2.REMOVE GENERATOR PULLEY WITH CLUTCH

a.

Mount the generator assembly in the vise between aluminum plates.


b.
A351775E05
1.302,1.083 1.729,0.208 1.729,0.208 1.573,0.208 false 2.26,0.479 2.042,0.917 true 2.969,1.115 2.854,1.583 2.854,1.583 2.719,1.583 true 1.594,1.958 0.948,1.521 true 1.094,0.125 1.583,0.281 0.49,0.156 10 false SST A 1.677,1.896 2.167,2.052 0.49,0.156 10 false SST B 2.302,0.365 2.5,0.521 0.198,0.156 10 false *a 2.271,1.51 2.76,1.667 0.49,0.156 10 false SST A

Install SST A and SST B to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  

Text in Illustration
*a Generator Rotor Shaft

NOTICE:

Securely attach SST to the generator pulley with clutch and generator rotor shaft.



c.
A351766E04
1.865,0.479 2.219,0.26 false 2.073,0.729 2.573,0.531 false 2.615,0.438 3.219,0.667 0.604,0.229 10 false SST A 2.24,0.135 2.844,0.354 0.604,0.219 10 false SST B 1.719,1.573 1.917,1.76 0.198,0.188 10 false *a

Using a wrench to hold SST A and turn SST B counterclockwise to loosen the generator pulley with clutch.

Text in Illustration
*a Hold
V100135

Turn

NOTICE:

Be careful as the generator pulley with clutch or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.



d.

Remove SST from the generator assembly.


e.

Remove the generator pulley with clutch from the generator rotor shaft.


f.

Remove the generator assembly from the vise.


Hide 27039 3.REMOVE REAR GENERATOR END COVER

a.

Place the generator assembly on the generator pulley with clutch.


b.
A351767

Remove the 3 bolts and rear generator end cover from the generator coil assembly.


Hide 27387 4.REMOVE TERMINAL INSULATOR

a.
A351768

Remove the terminal insulator from the generator coil assembly.


Hide 27370 5.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A351769

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 27360 6.REMOVE GENERATOR COIL ASSEMBLY

a.
A351770

Remove the 4 through bolts.


b.
A351771E01
0.64,1.72 1.046,2.024 1.046,2.024 1.158,2.024 false 1.986,0.951 2.487,0.709 2.487,0.709 2.565,0.709 false 2.611,0.624 2.959,0.794 0.349,0.170 10 SST 0.531,0.503 0.772,0.673 0.241,0.170 10 *a 1.189,1.933 1.537,2.103 0.349,0.170 10 SST

Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)

Text in Illustration
*a Hold
V100135

Turn


Hide 27444 7.REMOVE GENERATOR BEARING COVER PACKING

a.
A402476

Remove the generator bearing cover packing.

NOTICE:

If the generator bearing cover packing breaks, remove all broken pieces.


HINT:

The generator bearing cover packing may be installed on the generator rotor assembly.



Hide 27330 8.REMOVE GENERATOR ROTOR ASSEMBLY

a.

Remove the generator rotor assembly from the generator drive end frame.

NOTICE:

Do not drop the generator rotor assembly.



b.
A351772

Inspect the generator drive end frame bearing.

i.

Check that the generator drive end frame bearing is not rough or worn.

If necessary, replace the generator drive end frame bearing.



Hide 27310B 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A339226

Remove the 4 screws and retainer plate from the generator drive end frame.


b.
A351773E02
2.156,0.229 2.573,0.604 true 1.885,0.854 2.448,0.99 true 1.844,0.094 2.167,0.271 0.323,0.177 10 false SST 1.594,0.771 1.917,0.948 0.323,0.177 10 false SST

Using SST and a hammer, tap out the generator drive end frame bearing from the generator drive end frame.

SST
09950-70010  (09951-07100)