Home › Engine / Hybrid System › 2TR-FE (CHARGING) › GENERATOR (for 100A Type)
RM2850E _51 Engine / Hybrid System _073308 2TR-FE CHARGING _0357067 GENERATOR(for 100A Type) A

2TR-FE CHARGING  GENERATOR(for 100A Type)  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A339229E03
1.844,0.479 2.24,0.854 true 2.521,0.49 2.906,0.25 true 1.552,0.323 1.875,0.51 0.323,0.188 10 false SST 2.917,0.104 3.24,0.292 0.323,0.188 10 false SST

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-70010  (09951-07100)


b.
A339230E05
2.906,1.063 2.844,0.833 true 2.875,1.729 2.802,1.302 true 2.865,1.073 3.135,1.25 0.271,0.177 10 true *a 2.854,1.771 3.115,1.948 0.26,0.177 10 false *b

Fit the tabs on the retainer plate into the cutouts on the drive end frame to install the retainer plate.

Text in Illustration
*a Tab
*b Cutout


c.

Install the retainer plate with the 4 screws.

Torque:

2.3 N*m (23 kgf*cm, 20 in.*lbf)



Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Place the generator drive end frame assembly on the generator pulley with clutch.


b.

Install the generator rotor assembly to the generator drive end frame.

NOTICE:

Do not drop the generator rotor assembly.



Hide 27444 3.INSTALL GENERATOR BEARING COVER PACKING

NOTICE:

A new generator coil assembly comes with a generator bearing cover packing. Therefore, it is not necessary to install a new generator bearing cover packing when installing a new generator coil assembly.


a.
A402477E01
1.948,0.323 2.458,0.323 true 1.948,1.281 2.458,1.281 true 2.51,0.229 2.823,0.427 0.313,0.198 10 false *a 2.5,1.188 2.813,1.385 0.313,0.198 10 false *b

Install a new generator bearing cover packing to the generator coil assembly.

Text in Illustration
*a Protrusion
*b Groove

NOTICE:

Align the protrusion of the generator bearing cover packing with the groove of the generator coil assembly when installing.



Hide 27360 4.INSTALL GENERATOR COIL ASSEMBLY

a.
A399913E01
0.708,0.448 1.281,0.594 true 2.604,0.542 2.792,0.542 true 0.531,0.333 0.844,0.531 0.313,0.198 10 false *a 2.833,0.448 3.146,0.646 0.313,0.198 10 false *a

Using a 21 mm deep socket wrench and press, slowly press on the generator coil assembly.

Text in Illustration
*a 21 mm Deep Socket Wrench


b.

Install the generator coil assembly with the 4 through bolts.

Torque:

5.6 N*m (57 kgf*cm, 50 in.*lbf)



Hide 27370 5.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A113845E13
0.979,0.74 1.375,0.385 1.375,0.385 1.479,0.385 false 1.51,0.313 1.688,0.469 0.177,0.156 10 false *a

While pushing the 2 brushes into the generator brush holder assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.

Text in Illustration
*a Pin


b.
A351769E03
1.75,1.021 2.5,1.5 true 2.573,1.479 2.781,1.635 0.208,0.156 10 false *a

Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

Torque:

1.8 N*m (18 kgf*cm, 16 in.*lbf)



c.

Pull out the pin from the generator brush holder assembly.

Text in Illustration
*a Pin


Hide 27387 6.INSTALL TERMINAL INSULATOR

a.
A351774

Install the terminal insulator to the generator coil assembly.

NOTICE:

Make sure that the terminal insulator is installed with the correct orientation.



Hide 27039 7.INSTALL REAR GENERATOR END COVER

a.

Install the rear generator end cover to the generator coil assembly with the 3 bolts.

Torque:

4.6 N*m (47 kgf*cm, 41 in.*lbf)



Hide 27415 8.INSTALL GENERATOR PULLEY WITH CLUTCH

a.

Mount the generator assembly in the vise between aluminum plates.


b.

Temporarily install the generator pulley with clutch by hand.


c.
A351775E05
1.302,1.083 1.729,0.208 1.729,0.208 1.573,0.208 false 2.26,0.479 2.042,0.917 true 2.969,1.115 2.854,1.583 2.854,1.583 2.719,1.583 true 1.594,1.958 0.948,1.521 true 1.094,0.125 1.583,0.281 0.49,0.156 10 false SST A 1.677,1.896 2.167,2.052 0.49,0.156 10 false SST B 2.302,0.365 2.5,0.521 0.198,0.156 10 false *a 2.271,1.51 2.76,1.667 0.49,0.156 10 false SST A

Install SST A and SST B to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  

Text in Illustration
*a Generator Rotor Shaft

NOTICE:

Securely attach SST to the generator pulley with clutch and generator rotor shaft.



d.
A351776E02
0.833,1.302 0.698,0.917 0.698,0.917 0.594,0.917 false 1.167,1.063 0.927,0.458 0.927,0.458 0.823,0.458 false 0.146,0.802 0.708,0.979 0.563,0.177 10 false SST A 0.927,2.823 1.167,2.99 0.24,0.167 10 false *a 1.385,4.188 1.625,4.354 0.24,0.167 10 false *c 1.906,2.417 2.146,2.583 0.24,0.167 10 false *b 0.385,0.354 0.938,0.531 0.552,0.177 10 false SST B

Using a wrench to hold SST A, turn SST B clockwise to tighten the generator pulley with clutch.

Torque:
Specified tightening torque:

80 N*m (816 kgf*cm, 59 ft.*lbf)


Text in Illustration
*a Hold
*b Torque Wrench Fulcrum Length
*c SST Fulcrum Length
V100135

Turn

NOTICE:

Be careful as the generator pulley with clutch or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When using SST (fulcrum length of 100 mm (3.94 in.)) + torque wrench (fulcrum length of 400 mm (15.8 in.)):

64 N*m (653 kgf*cm, 47 ft.*lbf)




e.

Remove SST from the generator assembly.


f.

Check that the generator pulley with clutch rotates smoothly.


g.

Remove the generator assembly from the vise.


Hide 27416 9.INSTALL GENERATOR PULLEY CAP

a.

Install a new generator pulley cap to generator pulley with clutch.