Home › Engine / Hybrid System › 14B (CHARGING) › GENERATOR › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073310 14B CHARGING _0357072 GENERATOR A

14B CHARGING  GENERATOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 27020 1.INSTALL GENERATOR ASSEMBLY

a.
A399924E01
0.302,1.615 1.656,1.979 true 1.792,0.063 2.104,0.26 0.313,0.198 10 false *a 2.583,1.51 2.813,1.708 0.229,0.198 10 true *b 2.76,1.656 3.073,1.854 0.313,0.198 10 false *a 0.115,1.521 0.427,1.719 0.313,0.198 11 false *1

Install the generator assembly with the 2 bolts labeled A.

Torque:
for bolt A:

35 N*m (357 kgf*cm , 26 ft.*lbf)



b.

Install the wiring harness bracket with bolt labeled B.

Text in Illustration
*a Wiring Harness Bracket
*b Bolt A
*c Bolt B


c.

Connect the connector and attach the clamps.


d.

Install the nut to connect terminal B.

Torque:

9.8 N*m (100 kgf*cm , 87 in.*lbf)



e.

Install the terminal cap.


Hide 16361A 2.INSTALL FAN AND GENERATOR V BELT

Hide 88310A 3.INSTALL V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (w/ Air Conditioning System)

Hide 58701A 4.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY

a.

Install the front engine service cover panel sub-assembly with the 3 bolts.

Torque:

8.0 N*m (82 kgf*cm , 71 in.*lbf)



b.

Install the shift wire clamp with the nut.

Torque:

12 N*m (122 kgf*cm , 9 ft.*lbf)



Hide 33506F 5.INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

a.
A146457E02
0.667,0.073 0.781,0.219 0.115,0.146 10 true A 0.49,1.906 0.604,2.052 0.115,0.146 10 true A 2.76,1.74 2.875,1.885 0.115,0.146 10 true B 2.729,0.219 2.844,0.365 0.115,0.146 10 true B

Install the floor shift control shift lever retainer sub-assembly with the 4 bolts.

Torque:
for bolt A:

7.5 N*m (76 kgf*cm, 66 in.*lbf)

for bolt B:

12 N*m (122 kgf*cm, 9 ft.*lbf)



b.
A399497E01
0.458,1.063 0.771,0.854 true 0.396,2.615 0.573,2.823 0.177,0.208 10 true *a 0.281,0.99 0.458,1.198 0.177,0.208 10 false *b 0.958,0.198 1.135,0.406 0.177,0.208 10 false *c 2.156,1.021 2.333,1.229 0.177,0.208 10 true *c 2.219,2.917 2.396,3.125 0.177,0.208 10 true *c

Connect the select cable and shift cable and install the nut, washer plate and new 3 clips.

Text in Illustration
*a Nut
*b Washer Plate
*c Clip


Hide 58123A 6.INSTALL SHIFT AND SELECT LEVER SUPPORT WITH BOOTS

a.

Install the shift and select lever support with boots with the 4 bolts.

Torque:

8.0 N*m (82 kgf*cm, 71 in.*lbf)



b.

Install the transmission cover mat.


c.

Install the shift lever knob sub-assembly.


Hide 58420 7.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

a.
A400621E01
2.063,0.542 2.219,1.229 true 1.938,0.313 2.135,0.531 0.198,0.219 10 true *a

Attach the 2 guides and install the No. 2 engine service hole cover assembly, Turn the knob to attach the hook.

Text in Illustration
*a Knob


Hide 58521D 8.INSTALL ENGINE SERVICE HOLE COVER MAT

a.

Install the engine service hole cover mat.


Hide 58734B 9.INSTALL REAR ENGINE SERVICE COVER WEATHERSTRIP

a.

Install the rear engine service cover weatherstrip.


Hide 58410 10.INSTALL ENGINE SERVICE HOLE COVER

a.

Attach the 2 guides and 2 hooks to install the engine service hole main cover.


Hide 11.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION