Home › Engine / Hybrid System › 1HZ (CHARGING) › GENERATOR
RM2850E _51 Engine / Hybrid System _073312 1HZ CHARGING _0357076 GENERATOR A

1HZ CHARGING  GENERATOR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 58410 3.REMOVE ENGINE SERVICE HOLE COVER

a.
A399457

Detach the 2 hooks and 2 guides and remove the engine service hole main cover.


Hide 58734B 4.REMOVE REAR ENGINE SERVICE COVER WEATHERSTRIP

a.
A400617

Remove the rear engine service cover weatherstrip.


Hide 58521D 5.REMOVE ENGINE SERVICE HOLE COVER MAT

a.
A399454

Remove the engine service hole cover mat.


Hide 58420 6.REMOVE NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

a.
A399455E01
2.302,1.25 3.01,0.521 true 3.031,0.396 3.344,0.594 0.313,0.198 10 false *a

Turn the knob to detach the hook, detach the 2 guides and remove the No. 2 engine service hole cover assembly.

Text in Illustration
*a Knob


Hide 58123A 7.REMOVE SHIFT AND SELECT LEVER SUPPORT WITH BOOTS

a.

Remove the shift lever knob sub-assembly.


b.

Remove the transmission cover mat.


c.
A400618

Remove the 4 bolts and remove the shift and select lever support with boots.


Hide 33506F 8.REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

a.
A399497E01
0.458,1.063 0.771,0.854 true 0.396,2.615 0.573,2.823 0.177,0.208 10 true *a 0.281,0.99 0.458,1.198 0.177,0.208 10 false *b 0.958,0.198 1.135,0.406 0.177,0.208 10 false *c 2.156,1.021 2.333,1.229 0.177,0.208 10 true *c 2.219,2.917 2.396,3.125 0.177,0.208 10 true *c

Remove the nut, washer plate, 3 clips and disconnect the select cable and the shift cable.

Text in Illustration
*a Nut
*b Washer Plate
*c Clip


b.
A399498

Remove the 4 bolts and remove the floor shift control shift lever retainer sub-assembly.


Hide 58701A 9.REMOVE FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY

a.
A400619

Remove the nut and disconnect the shift wire clamp from the front engine service cover panel sub-assembly.


b.
A400620

Remove the 3 bolts and remove the front engine service cover panel sub-assembly.


Hide 10.REMOVE NO. 1 V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT (w/ Air Conditioning System)

Hide 11.DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 12.REMOVE FAN AND GENERATOR V BELT

Hide 13.REMOVE GENERATOR ASSEMBLY

a.
A399919

Remove the terminal cap.


b.

Remove the nut and disconnect terminal B.


c.
A399920E01
1.896,0.354 2.208,0.552 0.313,0.198 10 true *a 0.479,0.208 0.667,0.406 0.188,0.198 10 true *b 0.948,1.385 1.135,1.583 0.188,0.198 10 true *c

Disconnect the connector and remove the bolt.

Text in Illustration
*a Nut
*b Connector
*c Bolt


d.
A399921

Remove the 2 bolts and generator assembly.