Home › Engine / Hybrid System › 1HZ (CHARGING) › GENERATOR
RM2850E _51 Engine / Hybrid System _073312 1HZ CHARGING _0357076 GENERATOR A

1HZ CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27411 1.REMOVE GENERATOR PULLEY

a.

Mount the generator assembly in a vise between aluminum plates.


b.
A401293E01
2.583,1.406 2.927,0.719 true 2.99,2.448 3.188,2.448 3.188,2.448 3.115,0.635 true 2.354,1.469 3,1.667 0.646,0.198 10 false SST 1-B 2.438,2.385 3.083,2.583 0.646,0.198 10 false SST 1-A 1.74,2.938 2.063,3.146 0.323,0.208 10 false *a 0.646,2.25 0.969,2.458 0.323,0.208 10 false *b

Install SST 1-A to the generator pulley shaft.

SST
09820-63011  (09820-06010, 09820-06021)

Item Part No.
SST 1-A and SST 1-B 09820-06010


c.

Install SST 1-B to SST 1-A.


d.

Hold SST 1-A with a torque wrench and turn SST 1-B clockwise with the specified torque.

Torque:

39 N*m (400 kgf*cm , 29 ft.*lbf)


NOTICE:

Make sure that SST is secured to the generator rotor shaft.


Text in Illustration
*a Hold
*b Turn


e.
A401294E01
2.24,1.688 2.552,1.885 0.313,0.198 10 false *a

Insert SST 2 and attach it to the generator pulley nut.

Item Part No.
SST 2 09820-06021

Text in Illustration
*a Insert


f.
A401295E01
0.875,2.563 1.188,2.76 0.313,0.198 10 false *a 2.885,1.521 3.094,1.75 0.208,0.229 10 false *b

To loosen the generator pulley nut, turn SST 1-A in the direction shown in the illustration.

NOTICE:

To prevent damage to the rotor shaft, do not loosen the generator pulley nut more than one-half of a turn.


Text in Illustration
*a Hold
*b Turn


g.

Remove SST 2 from the generator assembly.


h.
A401296E01
2.625,1.406 2.844,0.75 true 2.99,2.094 3.198,2.094 3.198,2.094 3.063,0.688 true 2.354,1.458 2.958,1.667 0.604,0.208 10 false SST 1-B 2.427,2.021 3.031,2.229 0.604,0.208 10 false SST 1-A 2.573,2.979 2.885,3.177 0.313,0.198 10 false *a 1.552,2.896 1.865,3.094 0.313,0.198 10 false *b

Turn SST 1-B in the direction shown in the illustration and remove SST 1-A and B.

Text in Illustration
*a Hold
*b Turn


i.

Remove the pulley nut and generator pulley.


Hide 27039 2.REMOVE REAR GENERATOR END COVER

a.
A401297

Remove the 3 nuts and rear generator end cover.


Hide 27387 3.REMOVE TERMINAL INSULATOR

a.
A157274

Remove the terminal insulator.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A157275

Remove the 2 screws and generator brush holder assembly.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A401298

Remove the 4 through bolts.


b.
A401299E01
2.333,1.198 2.74,2.271 true 3.115,0.927 3.365,1.135 0.25,0.208 10 false *b 0.594,1.427 0.844,1.635 0.25,0.208 10 false *a 2.646,2.323 2.99,2.531 0.344,0.208 10 false SST

Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)

Text in Illustration
*a Hold
*b Turn


Hide 27384 6.REMOVE WASHER

a.
A401300

Remove the washer.


Hide 27330 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A401301

Remove the generator rotor assembly from the generator drive end frame.

NOTICE:

Do not drop the generator rotor assembly.



b.

Inspect the generator drive end frame bearing.

i.
A157277

Check that the generator drive end frame bearing is not rough or worn.

If necessary, replace the generator drive end frame bearing.



Hide 27312 8.REMOVE RETAINER PLATE

a.
A401302

Remove the 4 screws and retainer plate.


Hide 27310B 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A401303E01
1.167,1.313 0.729,0.927 0.729,0.927 1.24,1.073 true 0.427,0.844 0.885,1.042 0.458,0.198 10 false SST

Using SST, tap out the generator drive end frame bearing.

SST
09950-60011  (09951-00250)
09950-70010  (09951-07100)