Home › Engine / Hybrid System › 1HZ (CHARGING) › GENERATOR
RM2850E _51 Engine / Hybrid System _073312 1HZ CHARGING _0357076 GENERATOR A

1HZ CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A401304E01
1.542,1.323 1.135,0.813 1.135,0.813 1.719,1.042 true 0.833,0.729 1.292,0.927 0.458,0.198 10 false SST

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-60011  (09951-00470)
09950-70010  (09951-07100)


Hide 27312 2.INSTALL RETAINER PLATE

a.
A401302E02
2,0.927 2.573,0.448 true 0.833,1.938 1.521,1.354 true 2.635,0.313 2.948,0.51 0.313,0.198 10 false *a 0.688,1.917 1,2.115 0.313,0.198 10 false *a

Align the claws of the bearing retainer with the grooves inside the drive end frame.

Text in Illustration
*a Claw


b.

Install the retainer plate with the 4 screws.

Torque:

2.3 N*m (23 kgf*cm , 20 in.*lbf)



Hide 27330 3.INSTALL GENERATOR ROTOR ASSEMBLY

a.
A401306

Install the generator rotor assembly to the generator drive end frame.

NOTICE:

Do not drop the generator rotor assembly.



Hide 27384 4.INSTALL WASHER

a.
A401300

Install a new washer.


Hide 27360 5.INSTALL GENERATOR COIL ASSEMBLY

a.
A401305E01
0.927,0.375 1.708,0.74 true 0.594,0.271 1.052,0.469 0.458,0.198 10 false SST

Using a deep socket wrench (21 mm) and a press, slowly press in the generator coil assembly.

Text in Illustration
*a 21 mm Deep Socket Wrench


b.
A401298

Install the generator coil assembly with the 4 through bolts.

Torque:

5.9 N*m (60 kgf*cm , 52 in.*lbf)



Hide 27370 6.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A160030E02
1.167,0.302 0.896,0.604 false 1.188,0.208 1.438,0.365 0.25,0.156 10 false *a

While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the brush holder hole.

Text in Illustration
*a Pin


b.
A157275E03
1.813,1.26 1.813,1.354 false 1.75,1.365 1.979,1.51 0.229,0.146 10 false *a

Install the generator brush holder assembly with the 2 screws.

Torque:

1.8 N*m (18 kgf*cm , 16 in.*lbf)



c.

Pull out the pin from the generator brush holder assembly.

Text in Illustration
*a Pin


Hide 27387 7.INSTALL TERMINAL INSULATOR

a.
A157281

Install the terminal insulator.

NOTICE:

Be sure to install the terminal insulator in the correct direction.



Hide 27039 8.INSTALL REAR GENERATOR END COVER

a.
A401297

Install the rear generator end cover with the 3 nuts.

Torque:

4.6 N*m (47 kgf*cm , 41 in.*lbf)



Hide 27411 9.INSTALL GENERATOR PULLEY

a.

Temporarily install the generator pulley by hand.


b.
A401293E01
2.583,1.406 2.927,0.719 true 2.99,2.448 3.188,2.448 3.188,2.448 3.115,0.635 true 2.354,1.469 3,1.667 0.646,0.198 10 false SST 1-B 2.438,2.385 3.083,2.583 0.646,0.198 10 false SST 1-A 1.74,2.938 2.063,3.146 0.323,0.208 10 false *a 0.646,2.25 0.969,2.458 0.323,0.208 10 false *b

Mount the generator assembly in a vise between aluminum plates.


c.

Install SST 1-A to the generator pulley shaft.

SST
09820-63011  (09820-06010, 09820-06021)

Item Part No.
SST 1-A and SST 1-B 09820-06010


d.

Install SST 1-B to SST 1-A.


e.

Hold SST 1-A with a torque wrench and turn SST 1-B clockwise with the specified torque.

Torque:

39 N*m (400 kgf*cm , 29 ft.*lbf)


NOTICE:

Make sure that SST is secured to the generator rotor shaft.


Text in Illustration
*a Hold
*b Turn


f.
A401294E01
2.24,1.688 2.552,1.885 0.313,0.198 10 false *a

Insert SST 2 and attach it to the generator pulley nut.

Item Part No.
SST 2 09820-06021

Text in Illustration
*a Insert


g.
A401307E01
2.99,1.479 3.302,1.677 0.313,0.198 10 false *b 0.823,2.49 1.135,2.688 0.313,0.198 10 false *a

Tighten the generator pulley nut by turning SST 1- A in the direction shown in the illustration.

Torque:

133 N*m (1356 kgf*cm , 98 ft.*lbf)


Text in Illustration
*a Hold
*b Turn


h.

Remove SST 2 from the generator assembly.


i.
A401296E01
2.625,1.406 2.844,0.75 true 2.99,2.094 3.198,2.094 3.198,2.094 3.063,0.688 true 2.354,1.458 2.958,1.667 0.604,0.208 10 false SST 1-B 2.427,2.021 3.031,2.229 0.604,0.208 10 false SST 1-A 2.573,2.979 2.885,3.177 0.313,0.198 10 false *a 1.552,2.896 1.865,3.094 0.313,0.198 10 false *b

Turn SST 1-B in the direction shown in the illustration and remove SST 1-A and B.


j.

Turn the generator pulley and check that the generator pulley moves smoothly.

Text in Illustration
*a Hold
*b Turn