Home › Engine / Hybrid System › 1HZ (CHARGING) › GENERATOR
RM2850E _51 Engine / Hybrid System _073312 1HZ CHARGING _0357076 GENERATOR A

1HZ CHARGING  GENERATOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 1.INSTALL GENERATOR ASSEMBLY

a.
A399921E01
1.188,0.188 1.417,0.406 0.229,0.219 10 true *a 2.635,0.979 2.865,1.198 0.229,0.219 10 true *b

Install the generator assembly with the 2 bolts.

Torque:
for bolt A:

79 N*m (806 kgf*cm, 58 ft.*lbf)

for bolt B:

64 N*m (650 kgf*cm, 47 ft.*lbf)


Text in Illustration
*a Bolt A
*b Bolt B


b.

Connect the connector and install the bolt.


c.

Install the nut to connect terminal B.

Torque:

9.8 N*m (100 kgf*cm, 87 in.*lbf)



d.

Install the terminal cap.


Hide 2.INSTALL FAN AND GENERATOR V BELT

Hide 3.CONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 4.INSTALL NO. 1 V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT (w/ Air Conditioning System)

Hide 58701A 5.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY

a.

Install the front engine service cover panel sub-assembly with the 3 bolts.

Torque:

8.0 N*m (82 kgf*cm, 71 in.*lbf)



b.

Install the shift wire clamp with the nut.

Torque:

12 N*m (122 kgf*cm, 9 ft.*lbf)



Hide 33506F 6.INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

a.
A146457E05
0.688,0.063 0.802,0.208 0.115,0.146 10 true A 0.479,1.917 0.719,2.094 0.24,0.177 10 true A 2.76,1.75 2.938,1.948 0.177,0.198 10 true B 2.729,0.198 2.875,0.344 0.146,0.146 10 true B

Install the floor shift control shift lever retainer sub-assembly with the 4 bolts.

Torque:
for bolt A:

7.5 N*m (76 kgf*cm, 66 in.*lbf)

for bolt B:

12 N*m (122 kgf*cm, 9 ft.*lbf)



b.
A399497E01
0.458,1.063 0.771,0.854 true 0.396,2.615 0.573,2.823 0.177,0.208 10 true *a 0.281,0.99 0.458,1.198 0.177,0.208 10 false *b 0.958,0.198 1.135,0.406 0.177,0.208 10 false *c 2.156,1.021 2.333,1.229 0.177,0.208 10 true *c 2.219,2.917 2.396,3.125 0.177,0.208 10 true *c

Connect the select cable and shift cable and install the nut, washer plate and new 3 clips.

Text in Illustration
*a Nut
*b Washer Plate
*c Clip


Hide 58123A 7.INSTALL SHIFT AND SELECT LEVER SUPPORT WITH BOOTS

a.

Install the shift and select lever support with boots with the 4 bolts.

Torque:

8.0 N*m (82 kgf*cm, 71 in.*lbf)



b.

Install the transmission cover mat.


c.

Install the shift lever knob sub-assembly.


Hide 58420 8.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

a.
A400621E01
2.063,0.542 2.219,1.229 true 1.938,0.313 2.135,0.531 0.198,0.219 10 true *a

Attach the 2 guides and install the No. 2 engine service hole cover assembly, Turn the knob to attach the hook.

Text in Illustration
*a Knob


Hide 58521D 9.INSTALL ENGINE SERVICE HOLE COVER MAT

a.

Install the engine service hole cover mat.


Hide 58734B 10.INSTALL REAR ENGINE SERVICE COVER WEATHERSTRIP

a.

Install the rear engine service cover weatherstrip.


Hide 58410 11.INSTALL ENGINE SERVICE HOLE COVER

a.

Attach the 2 guides and 2 hooks to install the engine service hole main cover.


Hide 12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION