Home › Engine / Hybrid System › N04C-UH (CHARGING) › GENERATOR
RM2850E _51 Engine / Hybrid System _073313 N04C-UH CHARGING _0357078 GENERATOR A

N04C-UH CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A157280

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-60011  (09951-00470)

SST
09950-70010  (09951-07100)


b.
A157278E03
1.042,0.625 1.458,1 false 1.948,1.313 2.354,1.563 false 0.875,0.51 1.063,0.677 0.188,0.167 10 false *a 2.396,1.49 2.563,1.646 0.167,0.156 10 false *a

Align the claws of the bearing retainer with the grooves inside the drive end frame.

Text in Illustration
*a Claw


c.

Install the bearing retainer with the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Install the generator rotor assembly and generator washer to the drive end frame.


Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A160029E02
2.073,0.208 1.885,0.438 false 2.094,0.042 2.375,0.271 0.281,0.229 10 false *a

Using a deep socket wrench (21 mm) and a press, slowly press in the generator coil assembly.

Text in Illustration
*a Deep Socket Wrench (21mm)


b.
A157276

Install the generator coil assembly with the 4 through bolts.

Torque:

5.9 N*m (60 kgf*cm, 52 in.*lbf)



Hide 27370 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A160030E02
1.167,0.302 0.896,0.604 false 1.188,0.208 1.438,0.365 0.25,0.156 10 false *a

While pushing the 2 brushes into the generator brush holder assembly, insert a φ1.0 mm (0.039 in.) pin into the generator brush holder hole.

Text in Illustration
*a Pin


b.
A157275E03
1.813,1.26 1.813,1.354 false 1.75,1.365 1.979,1.51 0.229,0.146 10 false *a

Install the generator brush holder assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the generator brush holder assembly.

Text in Illustration
*a Pin


Hide 27387 5.INSTALL TERMINAL INSULATOR

a.
A157281

Install the terminal insulator.


Hide 27039 6.INSTALL FRAME BRUSH COVER

a.
A157273

Install the frame brush cover with the 3 nuts.

Torque:

4.6 N*m (47 kgf*cm, 41 in.*lbf)



Hide 27411 7.INSTALL GENERATOR PULLEY

a.

Install the generator pulley to the generator rotor shaft by tightening the generator pulley nut by hand.


b.
A150487E02
2.612,0.627 2.784,0.775 0.172,0.147 10 *a 0.02,1.578 0.538,1.735 0.518,0.158 10 SST1-B 1.249,0.63 1.767,0.787 0.518,0.158 10 SST1-A 1.128,1.127 1.234,0.714 false 0.927,1.213 0.317,1.559 false

Hold SST1-A with a torque wrench, and tighten SST1-B clockwise to the specified torque.

SST
09820-63011  (09820-06010, 09820-06020)

HINT:
SST1-A and SST1-B 09820-06010


Torque:

39 N*m (400 kgf*cm, 29 ft.*lbf)


Text in Illustration
*a Turn

NOTICE:

Check that the SST is secured to the generator rotor shaft.



c.
A150488E03
1.132,1.002 1.302,1.155 0.17,0.153 10 *a 2.172,1.395 2.551,1.546 0.378,0.152 10 SST2 1.891,1.396 2.15,1.473 false

Mount SST2 in a vise.

HINT:
SST2 09820-06020



d.

Insert SST1-A and SST1-B into SST2, and attach the generator pulley nut to SST2.

Text in Illustration
*a Insert


e.
A150522E03
1.227,0.731 1.385,0.898 0.157,0.167 10 *a 2.684,0.6 3.196,0.776 0.512,0.176 10 SST1-A 2.255,0.729 2.655,0.684 false

Tighten the generator pulley nut by turning SST1-A in the direction shown in the illustration.

Torque:

133 N*m (1351 kgf*cm, 98 ft.*lbf)


Text in Illustration
*a Turn


f.

Remove the generator assembly from SST2.


g.
A150490E05
2.75,1.156 2.75,0.427 false 2.583,1.104 2.365,0.771 false 0.875,0.688 1.052,0.833 0.177,0.146 10 false *a 2.469,0.229 3.073,0.427 0.604,0.198 10 false SST1-B 1.875,0.625 2.396,0.802 0.521,0.177 10 false SST1-A

Turn SST1-B, and remove SST1-A and SST1-B.

Text in Illustration
*a Turn


h.

Turn the generator pulley, and check that the generator pulley moves smoothly.