Home › Engine / Hybrid System › N04C-VL CHARGING › GENERATOR
RM2850E _51 Engine / Hybrid System _073314 N04C-VL CHARGING _0357080 GENERATOR A

N04C-VL CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27411 1.REMOVE GENERATOR PULLEY

a.
A150487E02
2.612,0.627 2.784,0.775 0.172,0.147 10 *a 0.02,1.578 0.538,1.735 0.518,0.158 10 SST1-B 1.249,0.63 1.767,0.787 0.518,0.158 10 SST1-A 1.128,1.127 1.234,0.714 false 0.927,1.213 0.317,1.559 false

Hold SST1-A with a torque wrench, and tighten SST1-B clockwise to the specified torque.

SST
09820-63011  (09820-06010, 09820-06020)

HINT:
SST1-A and SST1-B 09820-06010


Torque:

39 N*m (400 kgf*cm, 29 ft.*lbf)


*a 09820-06010

NOTICE:

Check that SST is securely fitted onto the generator rotor shaft.



b.
A150488E03
1.132,1.002 1.302,1.155 0.17,0.153 10 *a 2.172,1.395 2.551,1.546 0.378,0.152 10 SST2 1.891,1.396 2.15,1.473 false

Mount SST2 in a vise.

HINT:
SST2 09820-06020



c.

Insert SST1-A and SST1-B into SST2, and attach the generator pulley nut to SST2.

Text in Illustration
*a Insert


d.
A150489E03
1.972,1.785 2.132,1.928 0.16,0.144 10 *a 2.659,0.739 3.175,0.919 0.516,0.18 10 SST1-A 2.259,0.849 2.644,0.825 false

To loosen the generator pulley nut, turn SST1-A in the direction shown in the illustration.

Text in Illustration
*a Turn

NOTICE:

To prevent damage to the rotor shaft, do not loosen the generator pulley nut by more than one-half turn.



e.

Remove the generator assembly from SST2.


f.
A150490E04
2.75,1.115 2.75,0.417 false 2.552,1.104 2.365,0.771 false 0.875,0.698 1.052,0.844 0.177,0.146 10 false *a 2.479,0.229 3.167,0.438 0.688,0.208 10 false SST1-B 1.896,0.615 2.417,0.792 0.521,0.177 10 false SST1-A

Turn SST1-B, and remove SST1-A and SST1-B.

Text in Illustration
*a Turn


g.

Remove the generator pulley nut and the generator pulley.


Hide 27039 2.REMOVE FRAME BRUSH COVER

a.
A157273

Remove the 3 nuts and frame brush cover.


Hide 27387 3.REMOVE TERMINAL INSULATOR

a.
A157274

Remove the terminal insulator.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A157275

Remove the 2 screws and generator brush holder assembly.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A157276

Remove the 4 through bolts.


b.
A428397E01
0.573,1.865 0.719,1.656 false 2.708,0.552 3.021,0.75 0.313,0.198 10 false *a 0.302,0.729 0.615,0.927 0.313,0.198 10 false *b 0.406,1.875 0.76,2.073 0.354,0.198 10 false SST

Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)

Text in Illustration
*a Turn
*b Hold


c.

Remove the generator washer.


Hide 27330 6.REMOVE GENERATOR ROTOR ASSEMBLY

a.

Remove the generator rotor assembly from the drive end frame.


Hide 27310B 7.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A157277

Inspect that the generator drive end frame bearing is not rough or worn. If necessary, replace the generator drive end frame bearing.


Hide 27310B 8.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A157278

Remove the 4 screws and bearing retainer.


b.
A157279E01
0.275,0.895 0.598,1.057 0.323,0.162 10 SST 1.183,0.994 0.653,0.994 0.653,0.994 1.146,1.232 false

Using SST, tap out the generator drive end frame bearing.

SST
09950-60011  (09951-00250)

SST
09950-70010  (09951-07100)