Home › Engine / Hybrid System › 14B (ENGINE MECHANICAL) › INJECTION TIMING › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073170 14B ENGINE MECHANICAL _0365276 INJECTION TIMING A

14B ENGINE MECHANICAL  INJECTION TIMING  INSPECTION AND ADJUSTMENT  


PROCEDURE

Hide 1.SET NO. 1 OR NO. 4 CYLINDER TO 35 - 62° BTDC/COMPRESSION

a.
A426988

Turn the crankshaft pulley clockwise so the pulley groove is 35 - 62° or more from the groove of the timing gear cover.


Hide 2.LOOSEN BOLTS HOLDING INJECTION PUMP STAY TO INJECTION PUMP

a.
A426989

Loosen the 2 bolts.


Hide 3.INSTALL SST AND DIAL INDICATOR

a.
A426990

Remove the plug bolt and gasket from the distributive head plug of the injection pump.


b.

Install SST (plunger stroke measuring tool) and a dial indicator to the plug bolt hole of distributive head plug.

SST
09275-54011  


Hide 4.RELEASE ACSD ADVANCE

a.
A426991

Using a screwdriver, turn the cold starting lever counterclockwise approx. 20°.


b.

Put a metal plate (thickness of 8.5 - 10.0 mm (0.335 - 0.394 in.)) between the cold starting lever and thermo wax plunger.


Hide 5.INSPECT AND ADJUST INJECTION TIMING

a.
A426992

Slowly rotate the crankshaft pulley counterclockwise and set the dial indicator at 0 mm (0 in.) when the dial indicator reaches the minimum value.


b.

Turn the crankshaft to the left and right and check that the dial indicator shows the minimum value.

NOTICE:

Check that the minimum value is set at 0 mm (0 in.)



c.
A426993

Slowly rotate the crankshaft pulley clockwise until its groove is aligned with the groove of the timing gear cover.


d.

Measure the plunger stroke.

Plunger stroke:
3B:

1.23 - 1.29 mm (0.0484 - 0.0508 in.)

14B:

1.31 - 1.37 mm (0.0516 - 0.0539 in.)

15B-F:

0.67 - 0.73 mm (0.0264 - 0.0287 in.)

15B-FT:

0.87 - 0.93 mm (0.0343 - 0.0366 in.)



e.
A426994

Loosen these nuts and bolts:

i.

4 union nuts holding injection pipes to injection pump


ii.

2 nuts holding injection pump to timing gear case

NOTICE:

Do not turn the nuts more than 90°.




f.
A426995

Adjust plunger stroke by slightly tilting the injection pump body.

If the stroke is less than specification, tilt the pump toward the engine.

If the stroke is greater than specification, tilt the pump away from the engine.


g.

Tighten these nuts and bolts:

2 nuts holding injection pump to timing gear case

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)

4 bolts holding injection pipes to injection pump

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


h.

Recheck the plunger stroke.


Hide 6.REMOVE METAL PLATE

Hide 7.REMOVE SST AND DIAL INDICATOR

a.

Remove the SST and dial indicator.

SST
09275-54011  


b.

Install a new gasket and the plug bolt of the distributive head plug.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)


Hide 8.TIGHTEN INJECTION PUMP STAY BOLTS

Torque:

29 N*m (300 kgf*cm, 21 ft.*lbf)


Hide 9.START ENGINE AND CHECK FOR FUEL LEAKS