Home › Drivetrain › CLUTCH › CLUTCH PEDAL(w/o Turn Over)
RM2850E _52 Drivetrain _073140 CLUTCH _0355886 CLUTCH PEDAL(w/o Turn Over) N

CLUTCH  CLUTCH PEDAL(w/o Turn Over)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST CLUTCH PEDAL HEIGHT

a.

Fold back the floor mat.


b.
C368720E01
1.281,0.677 1.698,0.271 1.698,0.271 1.833,0.271 true 1.198,0.76 1.531,1.115 1.531,1.115 1.667,1.115 true 1.354,2.969 1.75,2.719 1.75,2.719 1.885,2.719 true 1.208,3.083 1.458,3.406 1.458,3.406 1.594,3.406 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *A 0.115,2.281 0.427,2.479 0.313,0.198 10 false *B 1.896,0.188 2.208,0.385 0.313,0.198 10 false *1 1.708,1.031 2.021,1.229 0.313,0.198 10 false *2 2.448,1.698 2.76,1.896 0.313,0.198 10 false *a 2.448,4.063 2.76,4.26 0.313,0.198 10 false *a 1.656,3.333 1.969,3.531 0.313,0.198 10 false *1 1.948,2.646 2.26,2.844 0.313,0.198 10 false *3

Check that the pedal height is correct.

Pedal Height from Floor:

165 to 172 mm (6.50 to 6.77 in.)


Text in Illustration
*A w/o Exhaust Brake
*B w/ Exhaust Brake
*1 Lock Nut
*2 Clutch Pedal Stopper Bolt
*3 Exhaust Retarder Switch Assembly
*a Pedal height from floor


c.

w/o Exhaust Brake:

i.

Loosen the lock nut and turn the clutch pedal stopper bolt until the correct height is obtained.



d.

w/ Exhaust Brake:

i.
C371493E01
0.031,0.031 0.313,0.292 0.281,0.26 10 true *A 0.052,2.406 0.292,2.646 0.24,0.24 10 true *B

Disconnect the connector and detach the clamp.

Text in Illustration
*A w/ Clutch Booster
*B w/o Clutch Booster


ii.
C368719E01
1.552,1.708 1.865,1.906 0.313,0.198 10 false *a

Loosen the lock nut and turn the exhaust retarder switch assembly until the correct height is obtained.

NOTICE:

Check that the gap between the thread of the exhaust retarder switch assembly and No. 1 clutch pedal cushion is within the standard clearance when the clutch pedal is released slowly.


Standard Clearance:

0 to 0.5 mm (0 to 0.0196 in.)


Text in Illustration
*a 0 to 0.5 mm (0 to 0.0196 in.)



e.

Tighten the lock nut.

Torque:

25 N*m (255 kgf*cm, 18 ft.*lbf)



f.

w/ Exhaust Brake:

Connect the connector and attach the clamp.


g.

Install the floor mat.


Hide 2.INSPECT AND ADJUST PEDAL FREE PLAY AND PUSH ROD PLAY

a.
C368721E01
0.896,0.49 1.042,0.219 1.042,0.219 1.177,0.219 true 0.813,0.552 0.969,0.917 0.969,0.917 1.104,0.917 true 1.219,0.115 1.531,0.313 0.313,0.198 10 false *1 1.167,0.833 1.479,1.031 0.313,0.198 10 false *2 2.875,2.083 3.188,2.281 0.313,0.198 10 false *a 2.885,2.823 3.198,3.021 0.313,0.198 10 false *b

Check that pedal free play and push rod play are correct.

Text in Illustration
*1 Push Rod
*2 Lock Nut (Push rod play and free play adjustment point)
*a Push rod play
*b Pedal free play

HINT:

Pay close attention to the change in resistance to distinguish between pedal free play and push rod play while performing the inspection.


i.

Depress the pedal until the beginning of clutch resistance is felt.

Pedal Free Play:

5.0 to 20.0 mm (0.197 to 0.787 in.)



ii.

Gently depress the pedal until resistance begins to increase a little.

Push Rod Play at Pedal Top:

1.0 to 5.0 mm (0.0394 to 0.196 in.)




b.

If necessary, adjust the pedal free play and push rod play.

HINT:

The push rod play can be adjusted by changing the length of the push rod. Pedal free play changes together with push rod play.


i.

Loosen the lock nut and turn the push rod until the pedal free play and push rod play are within the specified ranges.

NOTICE:

If pedal free play and push rod play are not within the standard range even after adjustment, inspect the related parts.



ii.

Tighten the lock nut.

Torque:

12 N*m (120 kgf*cm, 9 ft.*lbf)


NOTICE:

When tightening the lock nut, be sure to hold the push rod clevis in place by its square portion.



iii.

After adjusting the pedal free play, check the pedal height.



Hide 3.INSPECT CLUTCH RELEASE POINT

a.
C368722E01
1.51,2.385 1.167,1.99 1.167,1.99 1.042,1.99 true 1.219,2.531 0.875,2.135 0.875,2.135 0.75,2.135 true 0.875,1.917 1.188,2.115 0.313,0.198 10 false *a 0.563,2.052 0.875,2.25 0.313,0.198 10 false *b 1.792,2.771 2.104,2.969 0.313,0.198 10 false *c 2.406,2.625 2.719,2.823 0.313,0.198 10 false *d

Check the clutch release point.

Text in Illustration
*a Release point
*b Full stroke end position
*c From pedal stroke end position to release point
*d Pedal stroke

i.

Pull the parking brake lever and install wheel chocks.


ii.

Start the engine and run it at idle.


iii.

Without depressing the clutch pedal, slowly move the shift lever to R until the gears contact.


iv.

Gradually depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.

Standard Distance:

25 mm (0.984 in.) or more (from pedal stroke end position to release point)


Pedal Stroke (Reference):

181 to 191 mm (7.13 to 7.51 in.)


HINT:

Perform inspection with the floor mat peeled back.


If the distance is not as specified, perform the following procedures:

·

Check the pedal height.

·

Check the push rod play and pedal free play.

·

Bleed the clutch line.

·

Check the clutch cover and disc.