TERMINALS OF ECU
| *a | Component without harness connected
(Skid Control ECU (Brake Actuator Assembly)) |
- | - |
| Terminal No. (Symbol) | Terminal Description |
|---|---|
| 1 (GND2) | Pump motor ground |
| 2 | - (Not used) |
| 3 | - (Not used) |
| 4 | - (Not used) |
| 5 | - (Not used) |
| 6 | - (Not used) |
| 7 (VSM2) | No. 2 vacuum booster pressure sensor (vacuum sensor assembly) power supply output |
| 8 | - (Not used) |
| 9 (VSG2) | No. 2 vacuum booster pressure sensor (vacuum sensor assembly) ground |
| 10 (CANL) | CAN communication line L |
| 11 | - (Not used) |
| 12 (IG1) | ECU power supply input |
| 13 (BM) | Motor relay power supply |
| 14 (SP1) | Speed signal output for speedometer |
| 15 (RR-) | Rear wheel speed RH (-) signal input |
| 16 (RR+) | Rear wheel speed RH (+) power supply output |
| 17 (FL-) | Front wheel speed LH (-) signal input |
| 18 (FL+) | Front wheel speed LH (+) power supply output |
| 19 | - (Not used) |
| 20 (VSM) | No .1 vacuum booster pressure sensor (vacuum sensor assembly) power supply output |
| 21 (VSG) | No. 1 vacuum booster pressure sensor (vacuum sensor assembly) ground |
| 22 (CANH) | CAN communication line H |
| 23 (FSW+) | Brake pedal load sensing switch (brake with switch pedal sub-assembly) input |
| 24 | - (Not used) |
| 25 (GND1) | Skid control ECU (brake actuator assembly) ground |
| 26 | - (Not used) |
| 27 | - (Not used) |
| 28 (RL-) | Rear wheel speed LH (-) signal input |
| 29 (RL+) | Rear wheel speed LH (+) power supply output |
| 30 (FR-) | Front wheel speed RH (-) signal input |
| 31 (FR+) | Front wheel speed RH (+) power supply output |
| 32 (VSI2) | No. 2 vacuum booster pressure sensor (vacuum sensor assembly) input |
| 33 (CSW) | VSC OFF switch (vehicle stability control switch) input |
| 34 (VSI1) | No. 1 vacuum booster pressure sensor (vacuum sensor assembly) input |
| 35 (STP) | Stop light switch assembly input |
| 36 | - (Not used) |
| 37 | - (Not used) |
| 38 (+BS) | Solenoid relay power supply |
TERMINAL INSPECTION
Disconnect the A71 connector and measure the voltage or resistance on the wire harness side.
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
- | - |
Voltage cannot be measured with the connector connected to the skid control (brake actuator assembly) as the connector is watertight.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A71-1 (GND2) - Body ground | W-B - Body ground | Pump motor ground | Always | Below 1 Ω |
| A71-12 (IG1) - Body ground | B - Body ground | ECU power supply input | Ignition switch ON | 11 to 14 V |
| A71-13 (BM) - Body ground | G - Body ground | Motor relay power supply | Always | 11 to 14 V |
| A71-14 (SP1) - Body ground | P - Body ground | Speed signal output for speedometer | Ignition switch ON | 11 to 14 V |
| A71-23 (FSW+) - Body ground | P - Body ground | Brake pedal load sensing switch (brake with switch pedal sub-assembly) input | Brake pedal depressed → released | 950 to 1050 Ω → 203 to 223 Ω |
| A71-25 (GND1) - Body ground | W-B - Body ground | Skid control ECU (brake actuator assembly) ground | Always | Below 1 Ω |
| A71-33 (CSW) - Body ground | LG - Body ground | VSC OFF switch (vehicle stability control switch) input | VSC OFF switch (vehicle stability control switch) pressed and held → released | Below 1 Ω → 10 kΩ or higher |
| A71-35 (STP) - Body ground | BE - Body ground | Stop light switch assembly input | Stop light switch assembly on → off (Brake pedal depressed → released) | 8 to 14 V → Below 1.5 V |
| A71-38 (+BS) - Body ground | GR - Body ground | Solenoid relay power supply | Always | 11 to 14 V |