| Line pressure (Wheel locked) | ||
| Engine idling | D position | 652 to 750 kPa (7.0 to 8.0 kgf*cm2, 95 to 109 psi) |
| R position | 1,213 to 1,409 kPa (12.0 to 14.0 kgf*cm2, 176 to 204 psi) | |
| AT stall (Throttle valve fully opened) | D position | 1,105 to 1,281 kPa (11.0 to 13.0 kgf*cm2, 160 to 186 psi) |
| R position | 1,572 to 1,827 kPa (16.0 to 19.0 kgf*cm2, 228 to 265 psi) | |
| Time lag | N → D position | Less than 1.2 second |
| N → R position | Less than 1.5 second | |
| Engine idle speed (A/C OFF) | N position | 640 to 660 rpm |
| Extension housing oil seal drive in depth | 1.0 to 2.0 mm (0.039 to 0.079 in.) | |
| Shift schedule D position | ||
| (Throttle valve fully opened) | 1 → 2 | 25 to 35 km/h (15 to 22 mph) |
| 2 → 3 | 52 to 63 km/h (32 to 40 mph) | |
| 3 → O/D | 83 to 96 km/h (51 to 60 mph) | |
| O/D → 3 | 79 to 86 km/h (49 to 54 mph) | |
| 3 → 2 | 43 to 48 km/h (26 to 30 mph) | |
| 2 → 1 | 18 to 23 km/h (11 to 15 mph) | |
| (Throttle valve fully closed) | 3 → O/D | 29 to 34 km/h (18 to 22 mph) |
| O/D → 3 | 23 to 28 km/h (14 to 18 mph) | |
| 2 position | ||
| (Throttle valve fully opened) | 1 → 2 | 25 to 35 km/h (15 to 22 mph) |
| 3 → 2 | 58 to 65 km/h (36 to 41 mph) | |
| 2 → 1 | 18 to 23 km/h (11 to 15 mph) | |
| L position | ||
| (Throttle valve fully opened) | 3 → 2 | 58 to 65 km/h (36 to 41 mph) |
| 2 → 1 | 23 to 28 km/h (14 to 18 mph) | |
| Lock-up point (Throttle valve opening 5 %) D position | ||
| O/D gear | Lock-up ON | 54 to 60 km/h (33 to 38 mph) |
| Lock-up OFF | 49 to 56 km/h (30 to 35 mph) | |
| 3rd gear | Lock-up ON | 54 to 60 km/h (33 to 38 mph) |
| Lock-up OFF | 49 to 56 km/h (30 to 35 mph) | |
| Park/neutral position switch assembly resistance | Standard | - |
| P (7 - 8) | Below 1 Ω | |
| Except P (7 - 8) | 10 kΩ or higher | |
| R (4 - 7) | Below 1 Ω | |
| Except R (4 - 7) | 10 kΩ or higher | |
| N (3 - 7) | Below 1 Ω | |
| Except N (3 - 7) | 10 kΩ or higher | |
| D (2 - 7) | Below 1 Ω | |
| Except D (2 - 7) | 10 kΩ or higher | |
| 2 (7 - 9) | Below 1 Ω | |
| Except 2 (7 - 9) | 10 kΩ or higher | |
| L (1 - 7) | Below 1 Ω | |
| Except L (1 - 7) | 10 kΩ or higher |
| Overdrive direct clutch drum sub-assembly inside diameter | Standard | 26.500 to 26.521 mm (1.0433 to 1.0441 in.) |
| Limit | 26.57 mm (1.0461 in.) | |
| Overdrive planetary gear assembly inside diameter | Standard | 12.00 to 12.018 mm (0.4724 to 0.4731 in.) |
| Limit | 12.070 mm (0.4752 in.) | |
| Overdrive planetary gear assembly thrust clearance | Standard | 0.2 to 0.59 mm (0.0079 to 0.0232 in.) |
| Limit | 0.8 mm (0.0315 in.) | |
| Piston stroke of overdrive direct clutch | Standard | 1.80 to 2.07 mm (0.0709 to 0.0815 in.) |
| Center support sum-assembly inside diameter | Standard | 35.00 to 35.025mm (1.378 to 1.3789 in.) |
| Limit | 35.08 mm (1.3811 in.) | |
| Front planetary sun gear sum-assembly inside diameter | Standard | 25.500 to 25.521 mm (1.0039 to 1.0048 in.) |
| Limit | 25.57 mm (1.0067 in.) | |
| Piston stroke of No.1 brake piston | Standard | 1.86 to 2.06 mm (0.0732 to 0.0811 in.) |
| Piston stroke of front clutch | Standard | 3.93 to 4.23 mm (0.1547 to 0.1665 in.) |
| Piston stroke of rear clutch | Standard | 2.00 to 2.20 mm (0.0787 to 0.0866 in.) |
| No.1 overdrive brake flange thickness | Standard | 4.9 to 5.0 mm (0.1929 to 0.1969 in.) |
| Limit | 5.0 mm (0.1969 in.) | |
| Overdrive brake piston stroke | Standard | 1.25 to 1.85 mm (0.0492 to 0.0728 in.) |
| Overdrive case sub-assembly inside diameter | Standard | 33.10 to 33.15 mm (1.3031 to 1.3051 in.) |
| Front planetary gear assembly thrust clearance | Standard | 0.20 to 0.59 mm (0.0079 to 0.0232 in.) |
| Limit | 0.8 mm (0.0315 in.) | |
| Output shaft sub-assembly inside diameter | Standard | 17.000 to 17.021 mm (0.6693 to 0.6701 in.) |
| Limit | 17.070 mm (0.672 in.) | |
| Rear planetary gear assembly thrust clearance | Standard | 0.20 to 0.59 mm (0.0079 to 0.0232 in.) |
| Limit | 0.8 mm (0.0315 in.) | |
| 1st and reverse brake return spring sum-assembly free length | Standard | 17.60 mm (0.6929 in.) |
| 1st and reverse brake piston stroke | Standard | 3.30 to 3.80 mm (0.1299 to 0.1496 in.) |
| Center support assembly | Standard | 0.3 to 0.7 mm (0.0118 to 0.0276 in.) |
| Limit | 0.7 mm (0.0276 in.) | |
| Input shaft end play | Standard | 0.3 to 0.7 mm (0.0118 to 0.0276 in.) |
| Piston stroke of overdrive direct clutch | Standard | 0.4 to 0.9 mm (0.0157 to 0.0354 in.) |
| Torque converter clutch sleeve runout | Maximum | 0.30 mm (0.0118 in.) |
| Drive plate runout | Maximum | 0.25 mm (0.0098 in.) |
| Front oil pump body sub-assembly busing inside diameter | Standard | 42.05 to 42.075 mm (1.6555 to 1.6565 in.) |
| Limit | 42.13 mm (1.6587 in.) | |
| Front oil pump cover sub-assembly busing inside diameter (Front side) | Standard | 24.000 to 24.021 mm (0.9449 to 0.9457 in.) |
| Limit | 24.07 mm (0.9476 in.) | |
| Front oil pump body sub-assembly busing inside diameter (Rear side) | Standard | 26.500 to 26.521 mm (1.0433 to 1.0441 in.) |
| Limit | 26.57 mm (1.0461 in.) | |
| Oil pump body clearance | Standard | 0.07 to 0.15 mm (0.0028 to 0.0059 in.) |
| Limit | 0.30 mm (0.0118 in.) | |
| Oil pump tip clearance | Standard | 0.14 to 0.24 mm (0.0055 to 0.0094 in.) |
| Limit | 0.30 mm (0.0118 in.) | |
| Oil pump side clearance | Standard | 0.02 to 0.05 mm (0.0008 to 0.0020 in.) |
| Dry fill | 13.9 liters (14.7 US qts, 12.2 lmp.qts) | Toyota Genuine ATF Type D-II |
| Drain and refill | 6.0 liters (6.3 US qts, 5.3 lmp.qts) |