Home › Engine / Hybrid System › 1HZ (EXHAUST) › EXHAUST PIPE › from 2019.08
RM2850E _51 Engine / Hybrid System _082621 1HZ EXHAUST _0399858 EXHAUST PIPE A

1HZ EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install a new gasket.

NOTICE:

Do not reuse the removed gasket.



b.

Temporarily install the front exhaust pipe assembly with 3 new nuts.


c.

Install the bolt.

Torque:
22.6 N*m (230 kgf*cm, 17 ft.*lbf)


d.

Tighten the 3 nuts.

Torque:

62 N*m (632 kgf*cm, 46 ft.*lbf)



Hide 17420 2.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.

Install the 2 new gaskets.

NOTICE:
·

Install the gasket in the correct direction.

·

Do not damage the outer surface of the gasket.

·

Do not reuse the removed gasket.

·

Do not push in the gasket with the center exhaust pipe assembly when connecting it.




b.

Temporarily install the center exhaust pipe assembly with 2 new nuts.


c.

w/o Exhaust Retarder Assembly:

Install the front exhaust pipe spacer and center exhaust pipe assembly with the 4 bolts.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


d.

w/ Exhaust Retarder Assembly:

Install the exhaust retarder assembly and center exhaust pipe assembly with the 4 bolts.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


e.

Tighten the 2 nuts.

Torque:
16.2 N*m (165 kgf*cm, 12 ft.*lbf)


Hide 44773D 3.CONNECT SOLENOID TO RETARDER HOSE (w/ Exhaust Retarder Assembly)

a.

Connect the solenoid to retarder hose.


Hide 17430 4.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.
A104634

Inspect the compression spring.

i.

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

40.0 mm (1.57 in.)


If the free length is less than the minimum, replace the compression spring.



b.

for RHD:

i.

Install a new gasket.

NOTICE:

Do not reuse the removed gasket.



ii.

Temporarily install the tail exhaust pipe assembly with 4 new nuts.


iii.

Install the 2 through bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


iv.
A448768N01
2.49,0.042 2.688,0.208 0.198,0.167 10 true A 3.104,0.042 3.302,0.208 0.198,0.167 10 true A 0.24,1.125 0.438,1.281 0.198,0.156 10 false B 0.823,0.99 1,1.146 0.177,0.156 10 true B

Tighten the 4 nuts.

Torque:
Nut A : 16.2 N*m (165 kgf*cm, 12 ft.*lbf)
Nut B : 6.0 N*m (61 kgf*cm, 53 in.*lbf)



c.

for LHD:

i.

Install a new gasket.

NOTICE:

Do not reuse the removed gasket.



ii.

Temporarily install the tail exhaust pipe assembly with the bolt and 2 new nuts.


iii.

Install the 2 through bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


iv.

Tighten the 2 nuts and bolt.

Torque:
Bolt : 22.6 N*m (230 kgf*cm, 17 ft.*lbf)
Nut : 16.2 N*m (165 kgf*cm, 12 ft.*lbf)