Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P2563  Turbocharger Boost Control Position Sensor "A" Circuit Range/Performance  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2563 Turbocharger Boost Control Position Sensor "A" Circuit Range/Performance Diagnosis Condition:
·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

When position sensor outputs abnormality signal for 1 second.


Malfunction Duration:

3 seconds or more


Turbocharger sub-assembly Class A DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2563
·

Idle the engine for 5 seconds after warming up the engine.

·

Ignition switch ON to OFF (wiping operation)



CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P2563 and other DTC are output A
DTC P2563 is output B


HINT:

If U010C is output, it may have been detected due to a CAN communication malfunction.




A

2.GO TO DTC CHART

B

6.REPLACE TURBOCHARGER SUB-ASSEMBLY
2.GO TO DTC CHART

NEXT

3.CHECK DTC OUTPUT (TURBOCHARGER SUB-ASSEMBLY)
3.CHECK DTC OUTPUT (TURBOCHARGER SUB-ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P2563 is output A
DTC P2563 is not output B




A

4.CHECK CONNECTOR CONNECTION CONDITION (TURBOCHARGER SUB-ASSEMBLY)

B

7.CHECK DTC OUTPUT
4.CHECK CONNECTOR CONNECTION CONDITION (TURBOCHARGER SUB-ASSEMBLY)
a.

Check the connector connection for the turbocharger sub-assembly connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT

NG

8.CONNECT SECURELY
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P2563 is output A
DTC P2563 is not output B




A

6.REPLACE TURBOCHARGER SUB-ASSEMBLY

B

7.CHECK DTC OUTPUT
6.REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Replace the turbocharger sub-assembly.

Click hereEngine / Hybrid System>N04C-WA (INTAKE)>TURBOCHARGER>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

8.CONNECT SECURELY
a.

Connect securely the turbocharger sub-assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT