Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0045  Turbocharger/Supercharger Boost Control "A" Circuit/Open  


DESCRIPTION

A385724E07
0,0.625 0.917,1.01 0.917,0.385 10 false Power Source (12 V) 0.5,1.417 1.729,1.688 1.229,0.271 10 false GND 0.438,2.719 1.667,2.99 1.229,0.271 10 false CAN-H 0.448,3 1.677,3.271 1.229,0.271 10 false CAN-L 1.427,3.25 2.406,3.5 0.979,0.25 10 false CAN I/F Block 1.542,5.083 2.406,5.667 0.865,0.583 10 false EEPROM 2.625,1.865 3.26,2.51 0.635,0.646 10 false Micro Computer 3.365,0.115 5.667,0.583 2.302,0.469 10 false Turbocharger Sub-assembly 3.729,0.938 4.99,1.219 1.26,0.281 10 false Motor drive I/F block 5.292,1.49 6.365,2.167 1.073,0.677 10 false Motor (U) 5.292,2.125 6.365,2.802 1.073,0.677 10 false Motor (V) 5.281,2.75 6.354,3.427 1.073,0.677 10 false Motor (W) 3.76,3.656 4.927,4.073 1.167,0.417 10 false Over current protection block 3.802,4.396 4.781,5.125 0.979,0.729 10 false Position sensor I/F block 5.948,3.625 6.927,4.354 0.979,0.729 10 false Position sensor (Hall IC) 6.208,1.49 7,1.75 0.792,0.26 10 false DC Motor 1.552,1.698 2.438,2.406 0.885,0.708 10 false Power supply block 5.135,4.208 6.115,4.938 0.979,0.729 10 false P/S (U, V, W) 5.01,4.646 6.49,5.323 1.479,0.677 10 false P/S (U+, V+, W+)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0045 Turbocharger/Supercharger Boost Control "A" Circuit/Open Diagnosis Condition:
·

Engine is running: at all times

·

Engine is stopped: while wiping operation


Malfunction Status:
·

When the voltage of each UVW coil is 1 V or less.


Malfunction Duration:

3 seconds or more


·

Harness or connector

·

Turbocharger sub-assembly


Class A DTC stored

MONITOR DESCRIPTION

·

The VNT actuator moves the nozzle vane steplessly by the LEA (Linear Electric Actuator) to control the turbo speed and boost pressure.

·

The LEA has a sensor to detect the movement of the actuator, always monitoring the target and actual value of the nozzle vane opening.

·

Wiping operation is performed while the engine is stopped for the purpose of removing soot and oil coming out from the range of vane operation and checking the turbo mechanical operating range for abnormality.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0045
·

Idle the engine for 5 seconds after warming up the engine.

·

Ignition switch ON to off (wiping operation)




WIRING DIAGRAM

A451038E03
2.021,1.375 3.906,1.906 1.885,0.531 10 false Turbocharger Sub-assembly 2.063,1.219 2.313,1.406 0.25,0.188 10 false j5 2.344,0.958 2.76,1.146 0.417,0.188 10 false HLG 2.344,0.427 2.76,0.615 0.417,0.188 10 false HLV 3.052,0.427 3.531,0.594 0.479,0.167 10 false CANH 3.042,0.979 3.521,1.146 0.479,0.167 10 false CANL 5.427,0.427 5.906,0.594 0.479,0.167 10 false CAN+ 5.417,0.969 5.896,1.135 0.479,0.167 10 false CAN- 5.01,0.406 5.438,0.583 0.427,0.177 10 false B142 5.01,0.938 5.438,1.177 0.427,0.24 10 false B142 5.438,2.146 5.917,2.313 0.479,0.167 10 false MREL 3.052,3.073 4.51,3.25 1.458,0.177 10 false ACT PWR 2.177,0.813 2.427,1 0.25,0.188 10 false 2 2.198,0.302 2.448,0.49 0.25,0.188 10 false 1 3.563,0.24 3.813,0.427 0.25,0.188 10 false 4 3.552,0.76 3.802,0.948 0.25,0.188 10 false 3 0.906,0.604 1.573,0.792 0.667,0.188 10 false EFI NO.3 1.385,2.802 2.063,2.99 0.677,0.188 10 false EFI-MAIN 0.594,4.26 1.208,4.448 0.615,0.188 10 false Battery 2.167,4.354 4.354,4.531 2.188,0.177 10 false : CAN Communication Line 4.615,2.104 5.01,2.313 0.396,0.208 10 false V-23 4.625,0.396 5.01,0.563 0.385,0.167 10 false E-59 4.635,0.927 5.021,1.094 0.385,0.167 10 false E-79 5.792,4.271 6.365,4.573 0.573,0.302 10 false ECM 5.083,2.438 5.406,2.615 0.323,0.177 10 false 27 5.104,0.229 5.427,0.406 0.323,0.177 10 false 80 5.052,0.76 5.375,0.938 0.323,0.177 10 false 102 4.625,3.146 5.01,3.323 0.385,0.177 10 false V-40 5.438,3.188 5.917,3.354 0.479,0.167 10 false E01 5.063,2.958 5.385,3.135 0.323,0.177 10 false 12 3.708,2.521 3.958,2.708 0.25,0.188 10 false 2 2.938,2.521 3.188,2.708 0.25,0.188 10 false 1 3.708,2.146 3.958,2.333 0.25,0.188 10 false 3 2.927,2.156 3.177,2.344 0.25,0.188 10 false 5 5.417,2.646 5.896,2.813 0.479,0.167 10 false MREL 5.083,1.927 5.406,2.104 0.323,0.177 10 false 26 4.99,2.125 5.417,2.365 0.427,0.24 10 false A115 5,2.635 5.427,2.875 0.427,0.24 10 false A115 2.396,2.781 3.073,2.969 0.677,0.188 10 false EFI NO.1 0.865,2.802 1.208,2.99 0.344,0.188 10 false P/I 0.5,3.083 1.917,3.375 1.417,0.292 10 false R/B NO.2-B 0.51,3.708 1.188,3.896 0.677,0.188 10 false FL MAIN 4.677,2.625 5.073,2.833 0.396,0.208 10 false V-3 5.01,3.156 5.438,3.396 0.427,0.24 10 false A115

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P0045 and other DTCs are output A
DTC P0045 is output B




A

2.GO TO DTC CHART

B

3.CHECK DTC OUTPUT
2.GO TO DTC CHART

b.

Repair any malfunctioning parts indicated by related DTCs.


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0045 is output A
DTCs are not output B




A

4.CHECK CONNECTOR CONNECTION CONDITION

B

7.CHECK DTC OUTPUT
4.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the turbocharger sub-assembly connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT

NG

9.CONNECT SECURELY
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0045 is output A
DTCs are not output B




A

6.CHECK TURBOCHARGER SUB-ASSEMBLY (WIPING OPERATION)

B

END

6.CHECK TURBOCHARGER SUB-ASSEMBLY (WIPING OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.

HINT:

Ignition switch ON to off verifies the wiping operation of the VNT actuator (DC motor).



e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0045 is not output A
DTC P0045 is output B




A

7.CHECK DTC OUTPUT

B

8.REPLACE TURBOCHARGER SUB-ASSEMBLY
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

8.REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Replace turbocharger sub-assembly.

Click hereEngine / Hybrid System>N04C-WA (INTAKE)>TURBOCHARGER>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
9.CONNECT SECURELY
a.

Connect securely the turbocharger sub-assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT