Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0421  Catalyst 1 Efficiency Below Threshold Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0421 Catalyst 1 Efficiency Below Threshold Bank 1 Diagnosis Condition:
·

The vehicle speed is 0 km/h.

·

A change in the engine revolution is 938 rpm or less.

·

A change in the fuel injection quantity is 312 mm3/st or less.

·

A change in the fuel pressure is 93.7 MPa or less.

·

The target operating current of the fuel pump is not less than 1500 mA but not more than 1800 mA.


Malfunction Status:

A change in the operating current of the fuel pump upon post injection exceeds the specified value.


Malfunction Duration:

10 seconds


·

No. 3 exhaust gas temperature sensor

·

Front exhaust pipe assembly

·

Low quality fuel


Class B2 DTC stored

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FUEL
a.

Open the fuel cap and check fuel for abnormality (in color and smell).


Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR CONNECTION CONDITION

NG

4.REPLACE FUEL
2.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the No. 3 exhaust gas temperature sensor.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK NO. 3 EXHAUST GAS TEMPERATURE SENSOR

NG

CONNECT SECURELY

3.CHECK NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the No. 3 exhaust gas temperature sensor for improper installation.


b.

Check the sensing area of the No. 3 exhaust gas temperature sensor for dirt, clogging, and damage.


Result:
Proceed to
OK
NG



OK

REPLACE FRONT EXHAUST PIPE ASSEMBLY

NG

CLEAN NO. 3 EXHAUST GAS TEMPERATURE SENSOR
HINT:
·

Clean the sensing unit and install it properly.

·

If damaged, replace the No. 3 exhaust gas temperature sensor.




4.REPLACE FUEL
a.

Replace the fuel with good quality fuel.


Result:
Proceed to
NEXT



NEXT

5.PERFORM PM FORCED REGENERATION
5.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read Current DTCs.

Result:
Result Proceed to
DTC P0421 is output A
DTCs are not output B




A

2.CHECK CONNECTOR CONNECTION CONDITION

B

END