Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P207F  Reductant Quality Performance  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P207F Reductant Quality Performance Diagnosis Condition:
·

With engine cold; conditions below continue for 3 seconds:

With engine hot; conditions below continue for 182 seconds:

-

Ignition switch ON

-

Urea solution tank level more than 25%

-

Urea solution tank temperature 1 higher than -5°C (23°F)

-

Urea solution tank temperature 2 higher than -5°C (23°F)

-

[Urea solution tank temperature 1 - temperature 2] below 30°C (86°F)

-

Exhaust gas temperature (DPR inlet), coolant temperature, and urea solution tank temperature 2 are no greater than 30°C (86°F).

-

There is no record of malfunction determination after the ignition switch ON.

-

Battery voltage is in the range of 10 V to 16 V

-

Urea sensor assembly is working normally.

-

There is no interruption between urea sensor assembly and CAN.



Malfunction Status:

The average value of urea solution concentration is below the standard value.


Malfunction Duration:

-


·

Nitrogen oxides sensor

·

Urea sensor assembly

·

Urea solution


Class C DTC stored

MONITOR DESCRIPTION

Poor urea solution quality is determined by the urea sensor assembly, which measures the urea concentration and determines its quality.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P207F Ignition switch ON for 182 seconds or more.


CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK UREA SOLUTION (AdBlue)
a.

Measure the urea solution concentration.

Standard values:

30 to 35%


HINT:

If the urea solution concentration is below the standard, drain the urea solution through the tank drain with the ignition switch ON, and then refill the tank with at least 5 liters of urea solution.

Afterward, drive the vehicle and check if the problem does not recur under driving conditions.



Result:
Proceed to
OK
NG



OK

2.CHECK UREA TANK

NG

9.REPLACE UREA SOLUTION (AdBlue)
2.CHECK UREA TANK
a.

Remove the urea tank sub-assembly from the vehicle.


b.

Remove the urea sensor assembly from the urea tank sub-assembly.


c.

Drain the urea solution from the urea tank sub-assembly and check the tank interior for the presence of foreign substances.


Result:
Proceed to
OK
NG



OK

3.CHECK UREA SENSOR ASSEMBLY

NG

8.CLEAN UREA TANK
3.CHECK UREA SENSOR ASSEMBLY
a.

Check the installation of the urea sensor assembly.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the urea sensor assembly.


Result:
Proceed to
OK
NG



OK

4.CHECK DTC OUTPUT

NG

7.REPAIR UREA SENSOR ASSEMBLY
4.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.


Result:
Result Proceed to
DTC P207F is output A
DTCs are not output B



A

5.REPLACE UREA SENSOR ASSEMBLY

B

END

5.REPLACE UREA SENSOR ASSEMBLY
a.

Repair the urea sensor assembly.


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPAIR UREA SENSOR ASSEMBLY
a.

Clean the sensing unit of the urea sensor assembly.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
8.CLEAN UREA TANK
a.

Remove the foreign substances and clean the urea tank sub-assembly interior.

NOTICE:

Use fresh water or a diluted urea solution to clean the urea tank sub-assembly interior.



Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
9.REPLACE UREA SOLUTION (AdBlue)
a.

Replace the urea solution (AdBlue)

HINT:

If the urea solution concentration is below the standard, drain the urea solution through the tank drain with the ignition switch ON, and then refill the tank with at least 6 liters (1.59 gallons) of urea solution.

Afterward, drive the vehicle and confirm that the problem does not recur under driving conditions.



Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT