When an injector assembly is replaced, the injector's compensation code must be input into the ECM.
When the ECM is changed, all of the existing injector compensation codes must be input into the new ECM.
22100
1. PUMP MACHINE DIFFERENCE LEARNING
Always perform this procedure after replacing the supply pump assembly or ECM.
When replacing the ECM, perform learning after injector ID registration.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Pump Machine Difference Learning.
According to the display on the GTS, perform pump machine difference learning.
89661A
2. PROTECTION DATA (SAVE)
Perform this procedure before replacing the ECM.
An ECM, wire harness or DLC3 connection malfunction may cause a malfunction during saving.
If the wire harness and DLC3 connection are normal after checking them, the ECM may be malfunctioning.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Enter the following menus: Powertrain / Engine / Utility / Protection Data.
According to the display on the GTS, save the protection data.
89661A
3. PROTECTION DATA (WRITE)
This procedure writes the data saved on the GTS in "Protection Data" to the new ECM.
An ECM, wire harness or DLC3 connection malfunction may cause a malfunction during saving.
If the wire harness and DLC3 connection are normal after checking them, the ECM may be malfunctioning.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Enter the following menus: Powertrain / Engine / Utility / Protection Data.
According to the display on the GTS, write the protection data.
89661A
4. PROTECTION DATA (CLEAR)
This procedure initializes data related to the engine that is saved in the ECM.
An ECM, wire harness or DLC3 connection malfunction may cause a malfunction during saving.
If the wire harness and DLC3 connection are normal after checking them, the ECM may be malfunctioning.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Enter the following menus: Powertrain / Engine / Utility / Protection Data.
According to the display on the GTS, reset the protection data.
89661A
5. LEARNING VALUES (SAVE)
Perform this procedure before replacing the ECM.
An ECM, wire harness or DLC3 connection malfunction may cause a malfunction during saving.
If the wire harness and DLC3 connection are normal after checking them, the ECM may be malfunctioning.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Enter the following menus: Powertrain / Engine / Utility / Learning Value.
According to the display on the GTS, save the learning value data.
89661A
6. LEARNING VALUES (WRITE)
This procedure writes the data saved on the GTS in "Learning Value" to the new ECM.
An ECM, wire harness or DLC3 connection malfunction may cause a malfunction during saving.
If the wire harness and DLC3 connection are normal after checking them, the ECM may be malfunctioning.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Enter the following menus: Powertrain / Engine / Utility / Learning Value.
According to the display on the GTS, write the learning value data.
89661A
7. LEARNING VALUES (CLEAR)
This procedure initializes data related to the engine that is saved in the ECM.
An ECM, wire harness or DLC3 connection malfunction may cause a malfunction during saving.
If the wire harness and DLC3 connection are normal after checking them, the ECM may be malfunctioning.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Enter the following menus: Powertrain / Engine / Utility / Learning Value
According to the display on the GTS, reset the learning value data.
8. INJECTOR COMPENSATION (READ AND SAVE)
This procedure can be performed to read the ID code (30-digit) of all cylinders from the ECM and save them in the tool.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Enter the following menus: Powertrain / Engine / Utility / Injector Compensation.
According to the display on the GTS, read and save the compensation code.
9. INJECTOR COMPENSATION (WRITE)
This procedure uses the GTS to register the ID codes saved in the tool.
When the ECM is replaced (ID codes cannot be read) or the injector assembly is replaced, manually register the ID codes.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
When the ECM is replaced, P2696 is detected. Therefore, after completing the procedure, clear the DTCs.
Use the GTS to check for DTCs.
| *1 | Injector assembly |
| *a | Injector Compensation Code |
According to the display on the GTS, register the compensation code.
The ID code of the new replacement injector assembly is temporarily entered into the GTS for the cylinder it is to be installed to, so do not confuse the injector assembly and the cylinder it is to be installed to.
After completing the procedure, clear the DTCs.