SST (SIGNAL CHECK HARNESS) CONNECT
ECM uses waterproof connectors, the connectors cannot be inspected directly.
To prevent damage of the ECM connector, connect the signal check harness and perform measuring by bringing the test probe into contact with the signal check harness side.
Each ECM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition".
Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| V-19 (BATT) - V-40 (E01) | Battery (for measuring battery voltage and for ECM memory) | Always | 11 to 14 V |
| V-13 (IGSW) - V-40 (E01) | Ignition switch signal | Ignition switch ON | 11 to 14 V |
| V-33 (IG) - V-40 (E01) | Ignition switch signal | Ignition switch ON | 11 to 14 V |
| V-1 (+B) - V-40 (E01) | Power source of ECM | Ignition switch ON | 11 to 14 V |
| V-13 (+B1) - V-40 (E01) | Power source of ECM | Ignition switch ON | 11 to 14 V |
| V-37 (+B2) - V-40 (E01) | Power source of ECM | Ignition switch ON | 11 to 14 V |
| V-61 (+B3) - V-40 (E01) | Power source of ECM | Ignition switch ON | 11 to 14 V |
| V-3 (MREL) - V-40 (E01) | ·
EDU relay ·
ACT PWR relay |
Ignition switch ON | 0 to 2 V |
| V-23 (MREL) - V-40 (E01) | 20 seconds after ignition switch off | 11 to 14 V | |
| M-51 (VC) - E-77 (E4) | Power source of sensor (a specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| V-47 (VPA) - V-45 (EPA) | Accelerator pedal assembly | Ignition switch ON, accelerator pedal fully released | 0.6 to 1.0 V |
| Ignition switch ON, accelerator pedal fully depressed | 2.8 to 3.6 V | ||
| V-67 (VPA2) - V-65 (EPA2) | Accelerator pedal assembly (for sensor malfunction detection) | Ignition switch ON, accelerator pedal fully released | 1.4 to 1.8 V |
| Ignition switch ON, accelerator pedal fully depressed | 3.6 to 4.4 V | ||
| V-50 (VCPA) - V-45 (EPA) | Power source of accelerator pedal assembly | Ignition switch ON | 4.5 to 5.5 V |
| E-74 (VG) - E-57 (EVG) | Mass air flow meter | Engine is warmed up: Idling | 1.5 to 1.9 V |
| E-47 (THA) - M-32 (E2) | Intake air temperature sensor
(built into mass air flow meter) |
Engine is warmed up: Idling, IAT at 0 to 80°C (32 to 176°F) | 0.5 to 3.4 V |
| E-63 (THIA) - M-54 (E2) | Intake air temperature sensor (for intake manifold side) | Engine is warmed up: Idling, IAT at 0 to 80°C (32 to 176°F) | 1.0 to 4.4 V |
| E-66 (THW) - M-54 (E2) | Engine coolant temperature sensor | Idling, ECT at 80 to 120°C (176 to 248°F) | 0.2 to 1.0 V |
| E-44 (THAO) - M-54 (E2) | Intake air temperature sensor (for intercooler side) | Engine is warmed up: Idling, IAT at 0 to 80°C (32 to 176°F) | 1.0 to 4.4 V |
| E-14 (IJ1+) - E-15 (#1)
E-18 (IJ2+) - E-19 (#2) E-34 (IJ3+) - E-16 (#3) E-38 (IJ4+) - E-20 (#4) |
Injector assembly | Injector assembly Idling with warm engine | Pulse generation (See waveform 1) |
| V-71 (VCP1) - V-46 (E2) | Power source of differential pressure sensor | Ignition switch ON | 4.5 to 5.5 V |
| E-73 (G+) - E-54 (E5) | Camshaft position sensor | Idling with warm engine | Pulse generation (See waveform 2) |
| E-52 (NE+) - E-72 (NE-) | Crankshaft position sensor | Idling with warm engine | Pulse generation (See waveform 3) |
| V-29 (STP) - V-40 (E01) | Stop light switch assembly | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | 0 to 2 V | ||
| V-75 (ST1-) - V-40 (E01) | Stop light switch assembly (opposite to STP) | Ignition switch ON, brake pedal depressed | 0 to 2 V |
| Ignition switch ON, brake pedal released | 11 to 14 V | ||
| V-30 (TC) - V-40 (E01) | Terminal TC of DLC3 | Ignition switch ON | 11 to 14 V |
| V-12 (STA) - V-40 (E01) | Starter signal | Cranking | 6 V or more |
| V-34 (TAC) - V-40 (E01) | Engine speed | Idling | Pulse generation (See waveform 4) |
| V-9 (W) - V-40 (E01) | MIL | MIL illuminated | 0 to 2 V |
| MIL not illuminated | 11 to 14 V | ||
| V-14 (SP1) - V-40 (E01) | Speed signal from combination meter | Driving at vehicle speed of 20 km/h | Pulse generation (See waveform 5) |
| E-67 (PIM) - E-77 (E4) | Manifold absolute pressure sensor | Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied | 0.1 to 0.7 V |
| Same as atmospheric pressure | 0.8 to 1.5 V | ||
| Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied | 1.6 to 2.3 V | ||
| E-49 (PCR1) - V-40 (E01) | Fuel pressure sensor (built into common rail assembly) | Idling (Approximately 30 MPa (306 kgf/cm2, 4351 psi)) | 1.3 to 1.7 V |
| V-48 (FPR) - E-77 (E4) | No. 2 fuel pressure sensor | Idling with warm engine | 1.1 to 1.5 V |
| E-48 (THF) - M-54 (E2) | Fuel temperature sensor (built into supply pump assembly) | Ignition switch ON | 1.2 to 1.6 V |
| E-53 (VCG) - E-54 (E5) | Power source of camshaft position sensor | Ignition switch ON | 4.5 to 5.5 V |
| E-9 (PCV+) - E-10 (PCV-) | Suction control valve (built into supply pump assembly) | Idling | Pulse generation (See waveform 6) |
| E-62 (VTA1) - E-77 (E4) | Throttle position sensor (built into diesel throttle body) | Ignition switch ON, throttle valve fully closed | 0.5 to 1.5 V |
| Ignition switch ON, throttle valve fully opened | 3.2 to 4.2 V | ||
| E-2 (LUSL) - V-40 (E01) | Throttle actuator (built into diesel throttle body) duty signal | Accelerator pedal released → Accelerator pedal depressed (when throttle motor is operating) | Pulse generation (See waveform 7) |
| E-31 (FCV) - V-40 (E01) | Fuel addition cut valve assembly | Fuel addition cut valve assembly operation | 11 to 14 V |
| Fuel addition cut valve assembly not operation | 0 to 2 V | ||
| M-50 (THCO) - E-77 (E4) | No. 1 exhaust gas temperature sensor | Idling with warm engine
(No. 1 exhaust gas temperature at 50 to 150°C) |
2.5 to 4.5 V |
| V-57 (THO2) - V-46 (E2) | No. 2 exhaust gas temperature sensor | Idling with warm engine
(No. 2 exhaust gas temperature at 50 to 150°C) |
2.5 to 4.5 V |
| V-49 (THCI) - V-46 (E2) | No. 4 Exhaust gas temperature sensor | Idling with warm engine
(No. 4 exhaust gas temperature at 50 to 150°C) |
2.5 to 4.5 V |
| V-69 (THO) - V-46 (E2) | No. 3 Exhaust gas temperature sensor | Idling with warm engine
(No. 3 exhaust gas temperature at 50 to 150°C) |
2.5 to 4.5 V |
| M-30 (THG) - M-54 (E2) | Exhaust gas temperature sensor (for EGR cooler side) | Idling with warm engine
(exhaust gas temperature (for EGR cooler side) at 50 to 150°C) |
2.5 to 4.5 V |
| V-70 (PEX) - V-46 (E2) | Differential pressure sensor | Idling with warm engine | 0.5 to 1.0 V |
| V-56 (RGSW) - V-40 (E01) | DPR switch signal | DPR switch on | 11 to 14 V |
| DPR switch off | 0 to 2 V | ||
| E-3 (EXB) - V-40 (E01) | Exhaust brake with bracket solenoid assembly | Exhaust brake operating | 0 to 2 V |
| V-4 (EXB) - V-40 (E01) | Exhaust brake not operating | 11 to 14 V | |
| V-11 (NUSW) - V-40 (E01)* | Exhaust brake neutral switch assembly | Ignition switch ON, shift position is neutral | 11 to 14 V |
| Ignition switch ON, shift position is not neutral | 0 to 2 V | ||
| V-55 (CLSW) - V-40 (E01)* | Exhaust brake clutch switch (exhaust retarder switch assembly) | Clutch pedal depressed | 0 to 2 V |
| V-72 (RSW) - V-40 (E01)* | Back-up light switch | Back-up light switch off | 0 to 2 V |
| Back-up light switch on | 11 to 14 V | ||
| V-36 (CANH) - V-40 (E01) | CAN communication line | Engine stop and Ignition switch ON | Pulse generation (See waveform 8) |
| V-5 (CANL) - V-40 (E01) | CAN communication line | Engine stop and Ignition switch ON | Pulse generation (See waveform 9) |
| E-59 (CAN+) - V-40 (E01) | CAN communication line | Engine stop and Ignition switch ON | Pulse generation (See waveform 8) |
| E-79 (CAN-) - V-40 (E01) | CAN communication line | Engine stop and Ignition switch ON | Pulse generation (See waveform 9) |
| E-5 (FIV) - V-40 (E01) | Exhaust fuel addition injector assembly | Fuel addition injector assembly operating | Pulse generation (See waveform 10) |
| Fuel addition injector assembly not operating | 11 to 14 V | ||
| M-60 (PC) - M-48 (PRD) | Pressure discharge valve | Pressure discharge valve operating | Pulse generation (See waveform 11) |
| V-39 (E11) - Body ground | Ground | Always | Below 1 Ω |
| E-56 (E1) - Body ground | Ground | Always | Below 1 Ω |
| M-32 (E2) - Body ground | Ground | Always | Below 1 Ω |
| M-54 (E2) - Body ground | Ground | Always | Below 1 Ω |
| V-40 (E01) - Body ground | Ground | Always | Below 1 Ω |
| V-60 (E02) - Body ground | Ground | Always | Below 1 Ω |
| V-20 (EC) - Body ground | Ground | Always | Below 1 Ω |
| E-75 (SNE) - Body ground | Ground | Always | Below 1 Ω |
| M-69 (GLDI) - Body ground | Ground | Always | Below 1 Ω |
*: for Manual Transmission
Waveform 1
Injector assembly No. 1 injection signal
Injector assembly No. 2 injection signal
Injector assembly No. 3 injection signal
Injector assembly No. 4 injection signal
| Terminal No. (Symbol) | E-14 (IJ1+) - E-15 (#1)
E-18 (IJ2+) - E-19 (#2) E-34 (IJ3+) - E-16 (#3) E-38 (IJ4+) - E-20 (#4) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on the injector injection.
Waveform 2
Camshaft position sensor signal
| Terminal No. (Symbol) | E-73 (G+) - E-54 (E5) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on the engine speed.
Waveform 3
Crankshaft position sensor signal
| Terminal No. (Symbol) | E-52 (NE+) - E-72 (NE-) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on the engine speed.
Waveform 4
Engine speed signal
| Terminal No. (Symbol) | V-34 (TAC) - V-40 (E01) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Idling |
The wavelength becomes shorter as the engine speed increases.
Waveform 5
Vehicle speed signal
| Terminal No. (Symbol) | V-14 (SP1) - V-40 (E01) |
| Tool Setting | 5 V/DIV., 10 msec./DIV. |
| Condition | Driving at vehicle speed of 20 km/h |
The wavelength becomes shorter as the vehicle speed increases.
Waveform 6
Suction control valve signal
| Terminal No. (Symbol) | E-9 (PCV+) - E-10 (PCV-) |
| Tool Setting | 10 V/DIV., 5 msec./DIV. |
| Condition | Idling |
The waveform varies depending on the suction control valve operation.
Waveform 7
Throttle actuator signal
| Terminal No. (Symbol) | E-2 (LUSL) - V-40 (E01) |
| Tool Setting | 1 V/DIV., 2 msec./DIV |
| Condition | Accelerator pedal released → Accelerator pedal depressed (when throttle motor is operating) |
The waveform varies depending on the throttle valve operation
Waveform 8 (Reference)
CAN communication signal
| Terminal No. (Symbol) | V-36 (CANH) - V-40 (E01)
E-59 (CAN+) - V-40 (E01) |
| Tester Range | 1 V/DIV., 10 μsec./DIV. |
| Condition | Engine stop and Ignition switch ON |
The waveform varies depending on the CAN communication signal.
Waveform 9 (Reference)
CAN communication signal
| Terminal No. (Symbol) | V-16 (CANL) - V-40 (E01)
E-79 (CAN-) - V-40 (E01) |
| Tester Range | 1 V/DIV., 10 μsec./DIV. |
| Condition | Engine stop and Ignition switch ON |
The waveform varies depending on the CAN communication signal.
Waveform 10
fuel addition injector assembly signal
| Terminal No. (Symbol) | E-5(FIV) - V-40 (E01) |
| Tool Setting | 10 V/DIV., 50 msec./DIV. |
| Condition | Fuel addition injector assembly operating |
Waveform 11
Pressure discharge valve signal
| Terminal No. (Symbol) | M-60 (PC) - M-48 (PRD) |
| Tester Range | 1 V/DIV., 2 msec./DIV. |
| Condition | Pressure discharge valve operating |