FAIL-SAFE CHART
If any of the following DTCs are set, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily.
| DTC No. | Fail-safe Operation | Fail-safe Deactivation Condition |
|---|---|---|
| P003A | Engine output is insufficient. | After restoration to normal condition and IG off |
| P0045 | Engine output is insufficient. | After restoration to normal condition and IG off |
| P0048 | Engine output is insufficient. | After restoration to normal condition and IG off |
| P006E
P006F |
Engine output is insufficient. | After restoration to normal condition and IG off |
| P0101 | Engine output is insufficient. | After restoration to normal condition and IG off |
| P0104 | Engine output is insufficient. | After restoration to normal condition and IG off |
| P0106 | ·
Engine output is insufficient. ·
EGR valve fully closed. ·
DPR filter auto regeneration control is stopped. |
After restoration to normal condition and IG off |
| P0107
P0108 |
Engine output is insufficient. | After restoration to normal condition and IG off |
| P0117
P0118 |
Engine output is insufficient. | After restoration to normal condition |
| P0122
P0123 |
Engine output is insufficient. | After restoration to normal condition |
| P016F | ·
Engine output is insufficient. ·
VNT control does not work. ·
EGR valve is fully closed. ·
DPR cannot be regenerated. ·
Exhaust emission performance may becomes deteriorated. ·
Urea SCR control does not work. |
After restoration to normal condition |
| P0200
P0611 |
·
Engine output is insufficient. ·
EGR control does not work. ·
VNT control does not work. ·
Urea SCR control does not work. |
After normal operation is restored and engine is restarted after engine stall |
| P0201
P0202 P0203 P0204 |
Engine is stopped, and cannot be restarted. | Normal operation is restored and after the accelerator pedal is fully closed |
| P0335 | ·
Engine output is insufficient. ·
VNT control does not work. ·
EGR valve is fully closed. ·
DPR cannot be regenerated. ·
Exhaust emission performance may becomes deteriorated. ·
Urea SCR control does not work. |
After normal operation is restored |
| P0401 | Engine output is insufficient. | After restoration to normal condition and IG off |
| P0402 | ·
Engine output is insufficient. ·
EGR valve is fully closed. |
After restoration to normal condition and IG off |
| P0605 | ·
Engine output is insufficient. ·
Urea SCR control does not work. |
After restoration to normal condition and IG off |
| P0606 | Engine is stopped, and cannot be restarted. | After restoration to normal condition |
| P0607 | Engine output is insufficient. | After restoration to normal condition |
| P0628 | ·
DPR cannot be regenerated. ·
VNT control does not work. ·
EGR valve is fully closed. ·
Exhaust emission performance may becomes deteriorated. ·
Urea SCR control does not work. |
After restoration to normal condition and IG off |
| P0629 | ·
Engine output is insufficient. ·
Engine is stopped, and cannot be restarted. ·
DPR cannot be regenerated. ·
VNT control does not work. ·
EGR valve is fully closed. ·
Exhaust emission performance may becomes deteriorated. ·
Urea SCR control does not work. |
After restoration to normal condition and IG off |
| P104E
P104F |
Engine output is insufficient. | After restoration to normal condition and IG off |
| P119F | Engine output is insufficient. | After restoration to normal condition and IG off |
| P1458 | Engine output is insufficient. | After restoration to normal condition and IG off |
| P1459 | ·
Engine output is insufficient. ·
DPR cannot be regenerated. |
Normal operation is restored and after the accelerator pedal is fully closed |
| P203F | ·
Engine output is insufficient. ·
Vehicle does not speed up. |
Just after restoration to normal condition |
| P20CD
P20CE |
Fuel addition cut valve assembly closes. | Immediately after normal operation is restored |
| P20CF | Fuel addition cut valve assembly closes. | ·
When judged the trouble by aftertreatment fuel injector leakage: After DPR related memory is reset ·
Immediately after normal operation is restored |
| P2101 | ·
Engine output is insufficient. ·
The EGR control valve is closed fully. ·
The VNT control valve is opened fully. |
After normal operation is resumed and accelerator opening is fully closed |
| P2146
P2147 P2148 P2149 P2150 P2151 |
·
Engine output is insufficient. ·
Engine is stopped, and cannot be restarted. ·
VNT control does not work. ·
EGR valve is fully closed. ·
Exhaust emission performance may becomes deteriorated. ·
Urea SCR control does not work. ·
DPR cannot be regenerated. |
After normal operation is restored and engine is restarted after engine stall |
| P2162 | Engine output is insufficient. | Immediately after normal operation is restored |
| P2200 | Exhaust emission performance may becomes deteriorated. | Immediately after normal operation is restored |
| P2201 | Exhaust emission performance may becomes deteriorated. | Immediately after normal operation is restored |
| P2209 | Exhaust emission performance may becomes deteriorated. | After restoration to normal condition |
| P2226 | ·
Engine output is insufficient. ·
EGR control system does not work. ·
VNT control system does not work. ·
Urea SCR control does not work. |
After restoration to normal condition, and accelerator released |
| P2227 | Engine output is insufficient. | After restoration to normal condition and IG off |
| P2228
P2229 |
·
EGR control system does not work. ·
VNT control system does not work. ·
Injection control system of cleanup NOx is stopped. |
After restoration to normal condition, and accelerator released |
| P229E | Exhaust emission performance may becomes deteriorated. | After restoration to normal condition |
| P229F | Exhaust emission performance may becomes deteriorated. | After restoration to normal condition |
| P22A7 | Exhaust emission performance may becomes deteriorated. | After restoration to normal condition |
| P22D3 | Engine output is insufficient. | After restoration to normal condition and IG off |
| P242C
P242D |
DPR cannot be regenerated. | After restoration to normal condition |
| P244B | ·
Engine output is insufficient. ·
DPR automatic regeneration is not performed properly. |
Immediately after normal operation is restored and DPR-related memory is reset |
| P2483 | Exhaust emission performance may becomes deteriorated. | After restoration to normal condition |
| P24A2 | ·
DPR regeneration prohibited. ·
Long idling control in aftertreatment. |
Immediately after normal status is resumed |
| P24B5
P24B6 |
Overlooking of DPR damage. | After restoration to normal condition |
| P2563 | Engine output is insufficient. | After restoration to normal condition and IG off |
| P259E
P259F |
Engine output is insufficient. | After restoration to normal condition and IG off |
| P2A00
P2A01 |
Engine output is insufficient. | Immediately after the normal operation is resumed |
| P2BAE | Exhaust emission performance may becomes deteriorated. | After restoration to normal condition |
| U0073 | Engine output is insufficient. | Recovery from the accelerator OFF after normal recovery |
| U010A | Engine output is insufficient. | After restoration to normal condition and IG off |
| U010C | Engine output is insufficient. | After restoration to normal condition and IG off |
| U02A3 | Overlooking of DPR damage. | After restoration to normal condition |