READ DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are for reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Notes |
|---|---|---|---|
| Coolant Temperature | Engine coolant temperature:
Min.: -40°C, Max.: 140°C |
After warming up engine: 80 to 100°C (176 to 212°F) | - |
| Engine Speed | Engine speed:
Min.: 0 rpm, Max.: 16383.75 rpm |
Ignition switch ON: 0 rpm
(Engine not running) |
Engine speed displays a crankshaft position sensor output level. |
| Vehicle Speed | Vehicle speed:
Min.: 0 km/h, Max.: 255 km/h |
Actual vehicle speed | Speed indicated on speedometer |
| Intake Air Temperature (Intake Manifold) | Intake air temperature (intake manifold):
Min.: -40°C Max.: 210°C |
85°C or less | Intake air temperature (intake manifold) displays an output level of intake air temperature sensor. |
| Mass Air Flow | Air flow rate from mass air flow meter:
Min.: 0 g/s, Max.: 655.35 g/s |
Idling: 4.0 to 15.0 g/s | Mass air flow an output level of mass air flow meter |
| Common Rail Pressure | Common rail pressure:
Min.: 0 MPa, Max.: 250 MPa |
Idling: 25 to 35 MPa | - |
| Atmosphere Pressure | Atmospheric pressure value:
Min.: 0 kPa (0 mmHg, 0 in.Hg), Max.: 255 kPa (1912.6 mmHg, 75.3 in.Hg) |
Actual atmospheric pressure | - |
| Power Supply Voltage | Power supply voltage:
Min.: 0 V, Max.: 65.535 V |
Idling: 11 to 14 V | - |
| Intake Air Temperature (Air Flow) | Intake air temperature:
Min.: -40°C Max.: 215°C |
Same as ambient temperature | Intake air temperature an output level of mass air flow meter |
| Accelerator Position Sensor1 | Accelerator position sensor No. 1:
Min.: 0%, Max.: 100% |
·
Accelerator pedal released: 12 to 20% ·
Accelerator pedal depressed: 56 to 72% |
- |
| Accelerator Position Sensor2 | Accelerator position sensor No. 2:
Min.: 0%, Max.: 100% |
·
Accelerator pedal released: 28 to 36% ·
Accelerator pedal depressed: 72 to 88% |
- |
| Exhaust Fuel Addition Pressure | Exhaust fuel addition pressure:
Min.: 0 MPa, Max.: 655.35 MPa |
- | - |
| Engine Coolant Temperature 1 | Engine coolant temperature 1:
Min.: -40°C, Max.: 120°C |
Engine coolant temperature sensor output value | - |
| Intercooler Outlet Temperature | Intercooler outlet temperature:
Min.: -40°C, Max.: 210°C |
Intake air temperature sensor (for intercooler side) output value | - |
| Target Boost Pressure | Target boost pressure:
Min.: 0 kPa Max.: 2047.96 kPa |
- | - |
| Actual Boost Pressure | Actual boost pressure:
Min.: 0 kPa Max.: 2047.96 kPa |
- | - |
| NOx Sensor Concentration Bank 1 Sensor 1 | NOx sensor concentration bank 1 sensor 1:
Min.: -0.18, Max.: 3 |
- | - |
| NOx Sensor Concentration Bank 1 Sensor 2 | NOx sensor concentration bank 1 sensor 2:
Min.: -0.18, Max.: 3 |
- | - |
| Parking Brake Switch | Parking brake switch status
ON/OFF |
ON: Parking brake switch on | - |
| Reductant Average Consumption | Reductant average consumption:
Min.: 0, Max.: 8.83 L/h |
- | - |
| Reductant Level | Reductant level:
Min.: 0%, Max.: 100% |
- | - |
| Injection Volume | Injection volume:
Min.: 0 mm3/st, Max.: 1280 mm3/st |
Idling: 5.0 to 16.0 mm3/st | - |
| Exhaust Fuel Addition | Exhaust fuel addition:
Min.: 0 cc/min, Max.: 250 cc/min |
- | - |
| Fuel Cut Valve | Fuel cut valve status:
ON/OFF |
- | - |
| Clogged Exhaust Fuel Addition | Exhaust fuel addition malfunction:
ON/OFF |
- | - |
| Clogged Exhaust Fuel Addition 2 | Exhaust fuel addition 2 malfunction:
ON/OFF |
- | - |
| Lock-Up Signal | Lock-Up signal status:
ON/OFF |
- | - |
| AMT Shift Indication Enable (CAN) | AMT shift indication enable:
ON/OFF |
- | - |
| Neutral Position Signal (CAN) | Neutral Position signal (CAN) status:
Not Neutral/Neutral |
- | - |
| Power Cut Request (CAN) | Power cut request status:
ON/OFF |
- | - |
| Stop and Start Request | Stop and start request status:
ON/OFF |
- | - |
| SCR Exhaust Temperature | SCR exhaust temperature:
Min.: -40°C, Max.: 1735°C |
- | - |
| ATC Exhaust Temperature | ATC exhaust temperature:
Min.: -40°C, Max.: 1000°C |
- | - |
| Oxidation Catalyst Exhaust Temperature | Oxidation catalyst exhaust temperature:
Min.: -40°C, Max.: 1000°C |
- | - |
| Average Increasing Speed Deviation Time | Average increasing speed deviation time:
0 to 500 μs Min.: 0 μs, Max.: 500 μs |
- | - |
| EGR Ratio | EGR ratio:
Min.: 0%, Max.: 100% |
- | - |
| Oxygen Density (DPR Inlet) | Oxygen density (DPR inlet):
Min.: 0%, Max.: 25% |
- | - |
| Oxygen Density (DPR Outlet) | Oxygen density (DPR outlet)
Min.: 0%, Max.: 25% |
- | - |
| Exhaust Flow | Exhaust flow:
Min.: 0 L/s, Max.: 1000 L/s |
- | - |
| Intake Air Control Valve Position | Intake air control valve position:
Min.: 0%, Max.: 120% |
- | - |
| Exhaust Brake Lamp | Exhaust brake lamp status:
ON/OFF |
- | - |
| Preheater Lamp | Preheater lamp status:
ON/OFF |
- | - |
| MIL | MIL status:
ON/OFF |
- | - |
| WIF Lamp | WIF status:
ON/OFF |
- | - |
| Catalyst Regeneration Indicator Lamp | Catalyst regeneration indicator lamp status:
ON/OFF |
- | - |
| Catalyst Regeneration Display Lamp | Catalyst regeneration display lamp status:
ON/OFF |
- | - |
| Exhaust Brake Solenoid Valve | Exhaust brake solenoid valve status:
ON/OFF |
- | - |
| Starter Relay | Starter relay status:
ON/OFF |
- | - |
| Stop and Start Operating Permission Signal | Stop and Start operating permission signal:
ON/OFF |
- | - |
| Sensor Supply Voltage 1 | Sensor supply voltage 1:
Min.: 0 V, Max.: 25.5 V |
- | - |
| Sensor Supply Voltage 2 | Sensor supply voltage 2:
Min.: 0 V, Max.: 25.5 V |
- | - |
| Air Flow Sensor Supply Voltage | Mass air flow meter supply voltage:
Min.: 0 V, Max.: 50 V |
- | - |
| Pressure Discharge Valve Period | Pressure discharge valve period:
Min.: 0 ms, Max.: 6553.5 ms |
- | - |
| Pressure Discharge Valve Synchronization Drive Period | Pressure discharge valve synchronization drive period:
Min.: 0 ms, Max.: 6553.5 ms |
- | - |
| Warning Switch for Water in Fuel | Warning switch for water in fuel:
ON/OFF |
- | - |
| Engine Stop Request | Engine stop request:
ON/OFF |
- | - |
| ABS Operation Status | ABS operation status:
ON/OFF |
- | - |
| Stop and Start Operating Prohibition Request | Stop and Start operating prohibition request:
ON/OFF |
- | - |
| Brake Switch | Brake switch status:
ON/OFF |
- | - |
| Immobiliser | Immobiliser:
Available/Not Available |
- | - |
| Fuel Temperature | Fuel temperature:
Min.: -40°C, Max.: 140°C |
- | - |
| Target Intake Air Control Valve Position | Target intake air control valve position:
Min.: -20%, Max.: 120% |
- | - |
| Target Pump SCV Current | Pump open current value:
Min.: 0 mA, Max.: 8160 mA |
Idling: 1350 to 2200 mA | - |
| Accelerator Position Sensor No.1 Voltage | Accelerator Position Sensor No. 1 Voltage:
Min.: 0 V, Max.: 5 V |
·
Accelerator pedal released: 0.6 to 1.0 V ·
Accelerator pedal depressed: 3.0 to 3.9 V |
- |
| Accelerator Position Sensor No.2 Voltage | Accelerator Position Sensor No. 2 Voltage:
Min.: 0 V, Max.: 5 V |
·
Accelerator pedal released: 1.4 to 1.8 V ·
Accelerator pedal depressed: 3.8 to 4.6 V |
- |
| Start Switch | Start switch status:
ON/OFF |
- | - |
| Neutral Position Switch | Neutral position switch status:
ON/OFF |
- | - |
| Stop Light Switch | Stop light switch status:
ON/OFF |
- | - |
| Clogged Catalyst Risk Level | Clogged catalyst risk level:
ON/OFF |
- | - |
| Clogged Catalyst Warning Level | Clogged catalyst warning level:
ON/OFF |
- | - |
| Catalyst Regeneration Switch | Catalyst regeneration switch status:
ON/OFF |
- | - |
| Oil Pressure Warning Switch | Oil pressure warning switch status:
ON/OFF |
- | - |
| Engine Stop Switch | Engine stop switch status:
ON/OFF |
- | - |
| Key Switch | Key switch status:
ON/OFF |
- | - |
| Idle Switch | Idle switch status:
ON/OFF |
- | - |
| Glow Relay | Glow relay status:
ON/OFF |
- | - |
| Actual EGR Valve Position | Actual EGR valve position:
Min.: 0%, Max.: 100% |
- | - |
| DPR Differential Pressure | DPR differential pressure:
Min.: -5 kPa, Max.: 100 kPa |
- | - |
| DPR Exhaust Temperature (IN) | DPR exhaust temperature (IN):
0 to 1000°C Min.: 0°C, Max.: 1000°C |
- | - |
| DPR Exhaust Temperature (OUT) | DPR exhaust temperature (OUT):
Min.: 0°C, Max.: 1000°C |
- | - |
| Target EGR Valve Position | Target EGR valve position:
Min.: 0%, Max.: 100% |
- | - |
| Target VN Turbo Position | Target VN turbo position:
Min.: 0%, Max.: 100% |
- | - |
| Target Engine Speed | Target engine speed:
Min.: 0 rpm, Max.: 4000 rpm |
- | - |
| Target Common Rail Pressure | Target common rail pressure:
Min.: 0 MPa, Max.: 250 MPa |
- | - |
| Target Accelerator Position | Target accelerator position:
Min.: 0%, Max.: 100% |
- | - |
| G Active Status | G active status:
ON/OFF |
- | - |
| NE Active Status | NE active status:
ON/OFF |
- | - |
| Catalyst Degradation | Catalyst degradation:
ON/OFF |
- | - |
| Catalyst Regeneration Switch (ECU) | Catalyst regeneration switch (ECU):
ON/OFF |
- | - |
| Cruise Control Release | Cruise control release:
ON/OFF |
- | - |
| Cruise Control Permission | Cruise control permission:
ON/OFF |
- | - |
| Integrated Post Injection Volume Limit | Integrated post injection volume limit:
ON/OFF |
- | - |
| DPR Mode | DPR mode:
0 to 255 |
- | - |
| DPR Deposition Value | DPR deposition value:
0 to 12.75 g Min.: 0 g, Max.: 12.75 g |
- | - |
| Pump Machine Difference Learning | Pump machine difference learning:
0 to 2 Min.: 0, Max.: 2 |
- | - |
| Actual VN Turbo Position | Actual VN turbo position:
Min.: 0%, Max.: 100% |
- | - |
| SCV Duty | SCV duty:
Min.: 0%, Max.: 100% |
- | - |
| SCV Current | SCV current:
Min.: 0 mA, Max.: 6000 mA |
- | - |
| SCV Current Feedback Value | SCV current feedback value:
Min.: -5000 mA, Max.: 5000 mA |
- | - |
| FCCB Injection Feedback Value #1 | Injection volume correction for cylinder 1:
Min.: -50 mm3/st, Max.: 50 mm3/st |
Idling: -7.0 to 7.0 mm3/st | - |
| FCCB Injection Feedback Value #2 | Injection volume correction for cylinder 2:
Min.: -50 mm3/st, Max.: 50 mm3/st |
Idling: -7.0 to 7.0 mm3/st | - |
| FCCB Injection Feedback Value #3 | Injection volume correction for cylinder 3:
Min.: -50 mm3/st, Max.: 50 mm3/st |
Idling: -7.0 to 7.0 mm3/st | - |
| FCCB Injection Feedback Value #4 | Injection volume correction for cylinder 4:
Min.: -50 mm3/st, Max.: 50 mm3/st |
Idling: -7.0 to 7.0 mm3/st | - |
| VNT Diagnosis Information 1 | VNT diagnosis information 1:
Min.: 0, Max.: 255 |
- | - |
| VNT Diagnosis Information 2 | VNT diagnosis information 2:
Min.: 0, Max.: 255 |
- | - |
| EGR Diagnosis Information 1 | EGR diagnosis information 1:
Min.: 0, Max.: 255 |
- | - |
| EGR Diagnosis Information 2 | EGR diagnosis information 2:
Min.: 0, Max.: 255 |
- | - |
| Engine Coolant Temperature 1 Supported | Engine coolant temperature 1 support:
Unsupp/Supp |
- | - |
| Intercooler Outlet Temperature Supported | Intercooler outlet temperature support:
Unsupp/Supp |
- | - |
Normal Condition: If no idling conditions are specified, the shift lever is in the neutral position, and the A/C switch and all accessory switches are off.
PERFORM ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the tester, perform the "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Notes |
|---|---|---|---|
| Control the Common Rail Pressure | The target common rail pressure changes according to the variable amount (%).
Check that the actual common rail pressure follows the target common rail pressure. |
-12.5 to 24.8% | Test possible when following conditions met:
·
Ignition switch ON ·
Engine running |
| Control the Cylinder Fuel Cut #4 | Stop fuel injection for cylinder 4 | ON or OFF | Test possible when following conditions met:
·
Ignition switch ON ·
Engine running |
| Control the Cylinder Fuel Cut #3 | Stop fuel injection for cylinder 3 | ON or OFF | Test possible when following conditions met:
·
Ignition switch ON ·
Engine running |
| Control the Cylinder Fuel Cut #2 | Stop fuel injection for cylinder 2 | ON or OFF | Test possible when following conditions met:
·
Ignition switch ON ·
Engine running |
| Control the Cylinder Fuel Cut #1 | Stop fuel injection for cylinder 1 | ON or OFF | Test possible when following conditions met:
·
Ignition switch ON ·
Engine running |
| Control the VN Turbo Position | The target VNT position can be changed in 10% increments from 0% to 100%.
Check that the actual VNT position follows. |
0 to 100% | Test possible when following conditions met:
·
Ignition switch ON ·
Engine stopped
|
| Check Fuel Leak | The engine speed increases up to approximately 1500 rpm, and the actual common rail pressure increases up to the target common rail pressure.
The engine speed and actual common rail pressure then return to their normal values, so tilt the cap and check for leaks. |
ON or OFF | Test possible when following conditions met:
·
Ignition switch ON ·
Engine running
|
| Control the EGR Valve Position | The specified EGR position can be changed in 10% increments from 0% to 100%.
Check that the EGR lift sensor position follows. |
0 to 100% | Test possible when following conditions met:
·
Ignition switch ON ·
Engine running |
| Control the Target Engine Speed | The engine speed increases from idling to 3000 rpm according to the variable amount. | 0 to 3000 rpm | Test possible when following conditions met:
·
Ignition switch ON ·
Engine running |
| Activate the VSV for Intake Control | The specified intake throttle valve position can be changed in 10% increments from 0% to 100%.
Check that the actual intake throttle valve position follows. |
0 to 100% | Test possible when following conditions met:
·
Ignition switch ON ·
Engine stopped
|
| Activate the Exhaust Brake Solenoid Valve | Perform a forced operation of the exhaust brake | ON or OFF | Test possible when following conditions met:
·
Ignition switch ON ·
Engine stopped |
| Reductant Quality Recheck Permission | - | ON or OFF |
|
| Activate the FCV | Perform a forced operation of the fuel addition cut valve assembly | ON or OFF | Test possible when following conditions met:
·
Ignition switch ON ·
Engine running |
| Drive History Information Trip Reset | Reset the driving information history | ON or OFF | Test possible when following conditions met:
·
Ignition switch ON ·
Engine stopped |
| Engine Stop | Stop fuel injection for all cylinders | Stop or Normal | Test possible when following conditions met:
·
Ignition switch ON ·
Engine running |
| Activate the Preheater | Perform a forced operation of the glow plug | ON or OFF | Test possible when following conditions met:
·
Ignition switch ON ·
Engine running
|
| Reductant SCR Memory Reset | Perform a memory reset for HC-SCR-related | ON or OFF | Test possible when following conditions met:
·
Ignition switch ON ·
Engine stopped |
| Differential Pressure Detection Permission Flag | - | ON or OFF |
|
| Activate the Catalyst Regeneration | Perform/do not perform PM forced regeneration control | ON or OFF | Test possible when following conditions met:
·
Ignition switch ON ·
Engine stopped
|