Home › Vehicle Interior › ENGINE HOOD / DOOR › AUTOMATIC DOOR SYSTEM (for Glide Type) › from 2019.08
RM2850E _58 Vehicle Interior _073213 ENGINE HOOD / DOOR _0357103 AUTOMATIC DOOR SYSTEM(for Glide Type) U

ENGINE HOOD / DOOR  AUTOMATIC DOOR SYSTEM(for Glide Type)  FAIL-SAFE CHART  


FAIL-SAFE CHART


a.

The door control relay assembly operates in fail safe mode if an abnormal condition such as those listed below has been detected.

Item Abnormality Detection Condition Fail-safe Operation Return Condition
Center door position malfunction Abnormal door position isdetected
While abnormality being detected
·

Center door motor is stopped and power is supplied to the magnetic clutch for 3 seconds.

·

Buzzer sounds for 3 seconds from when power supply to magnetic clutch started.


HINT:

If a center door fully-closed stateis detected before power supplyto the magnetic clutch starts, the magnetic clutch is turned off.


After abnormality detected
·

Intermittent clutch control continues until specified period of time elapses.

·

Auto control cannot beactivated.


HINT:

While intermittent clutch control is active, if a signal is input from the door control switch assembly, the buzzer sounds for 3 seconds.


Center door fully-closed state is detected.
Pulse Sensor Malfunction When the center door is in automatic opening or closing operation, abnormality in pulse sensor is detected.
While abnormality being detected
·

Center door motor is stopped and power is supplied to the magnetic clutch for 3 seconds.

·

Buzzer sounds for 3 seconds from when power supply to magnetic clutch started.


HINT:

If a center door fully-closed state is detected before power supply to the magnetic clutch starts, the magnetic clutch is turned off.


After abnormality detected

Intermittent clutch control is performed.


HINT:

While intermittent clutch control is active, if a signal is input from the door control switch assembly, the buzzer sounds.


Intermittent clutch control period has ended and center door fully closed state is detected.
Continuous power supply to driving motor in the same direction When power is supplied in the same direction to the center door motor for more than 30 seconds.
While abnormality being detected
·

Center door motor is stopped and power is supplied to the magnetic clutch for 3 seconds.

·

Buzzer sounds for 3 seconds from when power supply to magnetic clutch started.


HINT:

If a center door fully-closed stateis detected before power supply to the magnetic clutch starts, the magnetic clutch is turned off.


After abnormality detected

Strong brake control is performed.


HINT:

If the operating conditions are not met when a signal is input from the door control switch assembly, the buzzer sounds.


When power supply in the same direction to the center door motoris turned off.
Continuous power supply to the clutch Continuous power supply time to the magnetic clutch has elapsed 2 minutes.
HINT:

This does not include the time used for magnetic clutch operation under a fixed voltage while the slide door operation is suspended.


While abnormality being detected
·

Center door motor is stopped and power is supplied to the magnetic clutch for 3 seconds.

·

Buzzer sounds for 3 seconds from when power supply to magnetic clutch started.


HINT:

If a center door fully-closed stateis detected before power supply to the magnetic clutch starts, the magnetic clutch is turned off.


After abnormality detected

Strong brake control is performed.


HINT:

If the operating conditions are not met when a signal is input from the door control switch assembly, the buzzer sounds.


Continuous power supply to the magnetic clutch is turned off.
Latch malfunction If center door fully-closed state is not detected when closing operation is completed. Buzzer sounds for 15 seconds. Returns immediately.
Full open latch switch malfunction When the door has been obstructed several times in series within the range where full-openlatch can be held engaged.
While abnormality being detected

Buzzer sounds for 3 seconds.


After abnormality detected

When the door has been obstructed within the range where full-open latch can be held engaged before return conditions are met, the buzzer sounds for 3 seconds.


HINT:

Even after abnormality is detected, the center door operates automatically if the door control switch assembly input conditions are met.


While the center door is in automatic opening operation, the full-open switch is turned from off to on within the range where thefull-open latch can be held engaged.
Release motor switch malfunction While the release motor is in operation, full-switch abnormality or initial switch abnormality is detected.
While abnormality being detected
·

Center door motor is stopped and power is supplied to the magnetic clutch for 3 seconds.

·

Buzzer sounds for 3 seconds from when power supply to magnetic clutch started.


HINT:

If a center door fully-closed stateis detected before power supply to the magnetic clutch starts, the magnetic clutch is turned off.


After abnormality detected

Strong brake control is performed.


HINT:

If the operating conditions are notmet when a signal is input from the door control switch assembly, the buzzer sounds.


Resets the ECU power source