RM2850E
_V1
General
_073185
SPECIFICATIONS
_0400397
A861E AUTOMATIC TRANSMISSION / TRANSAXLE
F
SPECIFICATIONS A861E AUTOMATIC TRANSMISSION / TRANSAXLE SERVICE DATA
AUTOMATIC TRANSMISSION FLUID
| Dry fill
|
11.9 liters (12.6 US qts, 10.5 Imp. qts)
|
Toyota Genuine ATF type T-IV
|
ATF TEMPERATURE SENSOR
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 (OIL2) - 2 (GND)
|
Always
|
196 Ω to 469 kΩ
|
| 1 (OIL2) - Body ground
|
Always
|
10 kΩ or higher
|
| 2 (GND) - Body ground
|
Always
|
10 kΩ or higher
|
VALVE BODY ASSEMBLY
| Input shaft end play
|
Standard
|
0.30 to 0.90 mm (0.0119 to 0.0354 in.)
|
SHIFT SOLENOID VALVE
| Tester Connection
|
Condition
|
Specified Condition
|
| Shift solenoid valve S1, shift solenoid valve S2, shift solenoid valve S3 and shift solenoid valve S4
|
20 °C (68 °F)
|
11 to 15 Ω
|
PARK / NEUTRAL POSITION SWITCH
| Tester Connection
|
Condition
|
Specified Condition
|
| 4 (C) - 5 (PL)
|
Shift lever in P
|
Below 1 Ω
|
| Shift lever not in P
|
10 kΩ or higher
|
| 4 (C) - 9 (RL)
|
Shift lever in R
|
Below 1 Ω
|
| Shift lever not in R
|
10 kΩ or higher
|
| 4 (C) - 1 (NL)
|
Shift lever in N
|
Below 1 Ω
|
| Shift lever not in N
|
10 kΩ or higher
|
| 4 (C) - 8 (DL)
|
Shift lever in D
|
Below 1 Ω
|
| Shift lever not in D
|
10 kΩ or higher
|
| 4 (C) - 2 (3L)
|
Shift lever in 3
|
Below 1 Ω
|
| Shift lever not in 3
|
10 kΩ or higher
|
| 4 (C) - 7 (2L)
|
Shift lever in 2
|
Below 1 Ω
|
| Shift lever not in 2
|
10 kΩ or higher
|
| 4 (C) - 3 (LL)
|
Shift lever in L
|
Below 1 Ω
|
| Shift lever not in L
|
10 kΩ or higher
|
REVERSE WARNING BUZZER
| Measurement Condition
|
Specified Condition
|
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
|
Reverse Warning Buzzer Sounds
|
FLOOR SHIFT ASSEMBLY
| Item
|
Tester Connection
|
Condition
|
Specified Condition
|
| Transmission control switch
|
2 (IND) - 4 (E)
|
Transmission control switch ON
|
10 kΩ or higher
|
| Transmission control switch OFF
|
Below 1 Ω
|
| Shift lock solenoid
|
1 (SLS-) - 2 (SLS+)
|
Always
|
26 to 39 Ω or higher
|
| Shift lock control switch
|
2 (P) - 3 (P1)
|
P position (Release button isnot pushed)
|
Below 1 Ω
|
| 2 (P) - 3 (P1)
|
P position (Release button ispushed)
|
Below 1 Ω
|
| 2 (P) - 1 (P2)
|
| 2 (P) - 1 (P2)
|
R, N, D, 4, 2/L position
|
Below 1 Ω
|
| Shift lock control ECU
|
A-3 (ACC) - A-5 (E)
|
Ignition switch ACC
|
11 to 14 V
|
| A-4 (IG) - A-5 (E)
|
Ignition switch ON
|
11 to 14 V
|
| A-8 (STP) - A-5 (E)
|
Depressing brake pedal
|
11 to 14 V
|
| A-2 (KLS+) - A-5 (E)
|
Ignition switch ACC and P position
|
0 V
|
| Ignition switch ACC and except P position
|
7 to 12 V
|
| Ignition switch ACC and except P position (After approx. 1 second)
|
6 to 9.5 V
|
| B-2 (SLS+) - B-1 (SLS-)
|
Ignition switch ON and P position
|
0 V
|
| Depressing brake pedal
|
9 to 14 V
|
| Except P position
|
0 V
|
| C-3 (P1) - C-2 (P)
|
Ignition switch ON, P position and depressing brake pedal
|
0 V
|
| Shift except P position under conditions above
|
9.5 to 14 V
|
| C-1 (P2) - C-2 (P)
|
Ignition switch ACC and P position
|
9.5 to 14 V
|
| Shift except P position under conditions above
|
0 V
|
PATTERN SELECT SWITCH
| Tester Connection
|
Condition
|
Specified Condition
|
| 6 (HOLD) - 3 (E)
|
Pattrn select switch (PWR) pushed
|
Below 1 Ω
|
| Pattrn select switch (PWR) not pushed
|
10 kΩ or higher
|
| Measurement Condition
|
Specified Condition
|
| Battery positive (+) → 5 (ILL+) Battery negative (-) → 4 (ILL-)
|
Illuminates
|
AUTOMATIC TRANSMISSION ASSEMBLY
| Front oil pump oil seal
|
Standard Depth
|
0 to 0.1 mm (0 to 0.00393 in.)
|
TORQUE CONVERTER AND DRIVE PLATE
| Drive plate runout
|
Maximum
|
0.30 mm (0.0118 in.)
|