Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P204362  Reductant Temperature Sensor "A" Circuit Range/Performance Signal Compare Failure  


DESCRIPTION

In this troubleshooting, the urea solution temperature in the urea tank is detected using 2 types of sensors, comparison is performed with the engine coolant temperature, and the abnormality is determined based on the extent of deviation.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P204362 Reductant Temperature Sensor "A" Circuit Range/Performance Signal Compare Failure Diagnosis Condition:
·

Ignition switch ON.

·

The difference between the SCR inlet exhaust gas temperature and the engine coolant temperature is less than 8°C (14.4°F).

·

The current engine coolant temperature is lower than the engine coolant temperature the last time the ignition switch was turned off by 20°C (36°F) or more.


Malfunction Status:
·

The difference between the temperature sensor (urea pump) and the temperature sensor (urea sensor assembly) is 30°C (54°F) or more, and also the difference between the engine coolant temperature and the temperature sensor (urea sensor assembly) is more than 44°C (79.2°F).


Malfunction Duration:
·

48 seconds or more.


Temperature sensor (urea sensor assembly) Class C AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Description of malfunction

Temperature sensor (urea sensor assembly) malfunction detected.


Reset condition

After having restored to the normal conditions.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P204362 After warming up the engine, turn the ignition switch off. After the engine sufficiently cools, turn the ignition switch to ON for 50 seconds or more.

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (REDUCTANT TANK TEMPERATURE AND REDUCTANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Data List / Reductant Tank Temperature and Reductant Temperature.


e.

Read the value.

OK:

The difference between the Reductant Tank Temperature and the Reductant Temperature is 4°C (7.2°F) or less.



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

2.REPLACE TEMPERATURE SENSOR (UREA SENSOR ASSEMBLY)
2.REPLACE TEMPERATURE SENSOR (UREA SENSOR ASSEMBLY)
a.

Replace the temperature sensor (urea sensor assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P204362)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P204362)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END