Home › Engine / Hybrid System › N04C-WA (FUEL) › FUEL SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082613 N04C-WA FUEL _0400841 FUEL SYSTEM G

N04C-WA FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT FOR FUEL PRESSURE

a.

Read the Data List.

i.

Warm up the engine.


ii.

Turn the ignition switch off.


iii.

Connect the GTS to the DLC3.


iv.

Start the engine.


v.

Turn the GTS on.


vi.

Enter the following menus: Powertrain / Engine and ECT / Data List.


vii.

Read the Data List.

Tester Display Measurement Item/Range Normal Condition
Fuel Press Fuel pressure:
Min.: 0 kPa, Max.: 655350 kPa
Idling: 25000 to 35000 kPa



Hide 2.INSPECT FOR FUEL LEAK

a.

Perform the Active Test.

i.

Connect the GTS to the DLC3.


ii.

Start the engine.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


v.

Perform the Active Test.

Tester Display Test Details Control Range Diagnostic Notes
Test the Fuel Leak Pressurizes common rail internal fuel pressure, and checks for fuel leaks Stop or Start
·

Fuel pressure inside common rail is pressurized to specified value and engine speed is increased to 2000 rpm when Start is selected.

·

Above conditions preserved while Start is selected.





Hide 3.BLEED AIR FROM FUEL SYSTEM

a.
A450424C01
2.125,0.625 2.375,0.833 0.25,0.208 10 true *a
*a Bleeder Plug


Loosen the bleeder plug.

NOTICE:

Make sure that the drain plug on the filter on the fuel tank side are closed. Make sure that the drain plug on the filter on the fuel tank side is closed.



b.
A146771

Operate the hand pump on the fuel tank side to bleed air (from the fuel line).

NOTICE:
·

Place a receptacle under the fuel filter so as not to scatter fuel.

·

Use full strokes to operate the hand pump.

·

Hand pump operating speed should not exceed 2 times per second.

·

The hand pump becomes stiff to operate when the pressure at the supply pump assembly inlet is saturated.

·

If pumping is stopped while the air is being removed, any fuel remaining in the pipes may return to the tank, so pumping should be continued until all air is removed from the bleeder plug pipe.

·

If the operation of hand pump does not become stiff after pumping it 200 times, there may be insufficient gas or a leak in the pipe.

·

If there is a significant amount of air remaining in the fuel system, the engine will not start because the fuel pressure in the common rail does not exceed normal use parameters.




c.

Tighten the bleeder plug.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


d.

Start the engine.

NOTICE:
·

If there is a significant amount of air remaining in the fuel system, it may take more than 10 seconds for the engine to start.

·

Do not operate the starter continuously for more than 20 seconds.

·

Be sure not to drain the battery. (Be sure to use a fully charged battery)



i.

If you are able to start the engine, advance to the next point.

HINT:

If you are unable to start the engine, continue pumping until the hand pump movement becomes stiff.




e.

Turn the ignition switch off.


f.

Connect the GTS to DLC3.


g.

Turn the ignition switch to ON and turn the GTS on.


h.

Clear the detected trouble codes.


i.

Start the engine. (*A)


j.

Enter the following menus: Powertrain / Engine and ECT / Active test / Test the Fuel Leak. (*B)


k.

Stop and start the [Test the Fuel Leak] 5 times, with a 10-second interval between each. (*C)

A192848E13
1.158,1.314 1.328,1.475 0.17,0.161 10 *a 6.499,2.314 6.685,2.491 0.185,0.177 10 *b 1.759,0.964 1.935,1.16 0.176,0.196 10 *c 1.759,1.621 1.964,1.816 0.205,0.196 10 *d 2.83,1.888 3.002,2.058 0.172,0.17 10 *h 3.479,0.751 3.667,0.921 0.188,0.17 10 *h 2.822,0.823 3.0,0.994 0.177,0.17 10 *e 4.15,0.82 4.312,0.99 0.162,0.17 10 *f 5.365,0.82 5.535,0.99 0.17,0.17 10 *g 6.242,1.843 6.387,2.013 0.145,0.17 10 *i

Text in Illustration
*a Active Test Operation *b Time
*c ON *d OFF
*e 1st time *f 2nd time
*g 5th time *h 10 seconds
*i 3 minutes - -


l.

Idle for at least 3 minutes. (*D)


m.

Enter the following menus: Powertrain / Engine and ECT / DTC.


n.

Read the DTCs.

i.

If no trouble code is output, air bleeding is complete.


ii.

If a trouble code is output, carry out the following procedure.



o.

Clear the detected trouble codes.


p.

Carry out steps (*A), (*B), (*C), and (*D) above again.