Home › Vehicle Interior › ENGINE HOOD / DOOR › AUTO CENTER DOOR (for Glide Type) › from 2019.08
RM2850E _58 Vehicle Interior _073213 ENGINE HOOD / DOOR _0356367 AUTO CENTER DOOR(for Glide Type) N

ENGINE HOOD / DOOR  AUTO CENTER DOOR(for Glide Type)  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.



PROCEDURE

Hide 67003F 1.INSPECT CENTER DOOR PANEL

a.

Check that the clearance measurements of areas A to I are within the standard range.

B554673N01
3.167,0.906 3.323,1.104 0.156,0.198 10 false A 1.635,3.938 1.792,4.135 0.156,0.198 10 false B 1.229,3.396 1.385,3.594 0.156,0.198 10 false C 1.646,5.24 1.802,5.438 0.156,0.198 10 false D 1.26,4.75 1.417,4.948 0.156,0.198 10 false E 5.438,3.906 5.594,4.104 0.156,0.198 10 false F 5.813,3.396 5.969,3.594 0.156,0.198 10 false G 5.427,5.26 5.583,5.458 0.156,0.198 10 false H 5.698,4.74 5.854,4.938 0.156,0.198 10 false I

Standard:
Area Specified Condition Area Specified Condition
A 6.55 to 12.55 mm (0.258 to 0.494 in.) B 13.2 to 17.2 mm (0.520 to 0.677 in.)
C -2.0 to 2.0 mm (-0.0787 to 0.0787 in.) D 13.2 to 17.2 mm (0.520 to 0.677 in.)
E -2.0 to 2.0 mm (-0.0787 to 0.0787 in.) F 13.2 to 17.2 mm (0.520 to 0.677 in.)
G -2.0 to 2.0 mm (-0.0787 to 0.0787 in.) H 13.2 to 17.2 mm (0.520 to 0.677 in.)
I -2.0 to 2.0 mm (-0.0787 to 0.0787 in.) - -



Hide 67003F 2.ADJUST CENTER DOOR PANEL

B554674

a.

Loosen the glide door arm bracket link bolt and adjust the horizontal axis of the bottom of the door.


b.

Tighten the glide door arm bracket link bolt and nut after the adjustment.

Torque:
Nut : 25 N*m (255 kgf*cm, 18 ft.*lbf)
Bolt : 18 N*m (184 kgf*cm, 13 ft.*lbf)


c.

Loosen the glide door link nut and adjust the horizontal axis of the bottom of the door.


d.

Tighten the glide door link nut after the adjustment.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


e.

Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a brass bar and hammer.


f.

Tighten the striker mounting screws on the body after the adjustment.

Torque:

12 N*m (122 kgf*cm, 9 ft.*lbf)