Home › Vehicle Interior › DOOR LOCK › AUTO CENTER DOOR LOCK (for Glide Type) › from 2019.08
RM2850E _58 Vehicle Interior _073188 DOOR LOCK _0403741 AUTO CENTER DOOR LOCK(for Glide Type) G

DOOR LOCK  AUTO CENTER DOOR LOCK(for Glide Type)  INSPECTION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure below is for RHD vehicles.



PROCEDURE

Hide 69030B 1.INSPECT GLIDE DOOR OPEN LOCK ASSEMBLY

a.
B556724C02
1.094,4.167 1.542,4.167 true 1.979,4.167 2.427,4.167 true 0.292,0.271 0.604,0.427 0.313,0.156 10 false *a 0.354,1.833 0.667,1.99 0.313,0.156 10 false *b 0.958,3.396 1.271,3.552 0.313,0.156 10 false *c 0.969,4.115 1.281,4.271 0.313,0.156 10 false E 2.5,4.094 2.813,4.25 0.313,0.156 10 false +B
*a Closed (Locked)
*b Full Opened (Unlocked)
*c Component without harness connected
(Glide Door Open Lock Assembly)


Check the operation of the glide door open lock assembly.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (E) - 2 (+B) Glide Door Closed (Locked) 10 kΩ or higher
Glide Door Full Opened (Unlocked) Below 1 Ω


If the result is not as specified, replace the glide door open lock assembly.



Hide 85453 2.INSPECT DOOR CONTROL MOTOR

a.
B556725C02
1.135,2.594 1.49,2.594 true 1.104,3.094 1.229,3.094 1.229,3.094 1.49,2.802 true 2.333,3.229 2.01,3.229 2.01,3.229 1.781,2.813 true 2,2.781 2.354,2.781 true 1.99,2.573 2.344,2.573 true 1.698,2.531 1.469,2.281 1.469,2.281 1.167,2.281 true 2.813,0.344 3.125,0.5 0.313,0.156 10 false *a 3.115,0.354 3.427,0.51 0.313,0.156 10 false *b 0.323,1.406 0.635,1.563 0.313,0.156 10 false *c 0.917,0.271 1.229,0.427 0.313,0.156 10 false *d 2.219,0.219 2.531,0.375 0.313,0.156 10 false *e 2.698,0.708 2.885,0.854 0.188,0.146 10 true *f 2.781,1.885 3.094,2.042 0.313,0.156 10 false *g 0.51,0.813 0.823,0.969 0.313,0.156 10 false *h 1.615,0.146 1.927,0.302 0.313,0.156 10 false *i 2.458,0.469 2.771,0.625 0.313,0.156 10 false *j 2.823,1.292 3.135,1.448 0.313,0.156 10 false *k 0.167,2.208 0.479,2.365 0.313,0.156 10 false *l 0.813,2.542 1.208,2.708 0.396,0.167 10 false PSW 0.833,3.042 1.229,3.208 0.396,0.167 10 false LS2 0.99,2.24 1.385,2.406 0.396,0.167 10 false L- 2.385,2.521 2.781,2.688 0.396,0.167 10 false UL3 2.385,2.74 2.781,2.906 0.396,0.167 10 false UL 2.375,3.177 2.771,3.344 0.396,0.167 10 false ANRL
*a Forward Direction
*b Inverse Direction
*c Initial Stop
*d Initial Switch
*e Lever Full Stroke
*f Full Switch
*g Full Stop
*h 60°
*i 61.8°
*j 28.2°
*k 60°
*l Component without harness connected
(Door Control Motor)


Check the operation.

i.

Apply battery voltage and check the operation of the door control motor.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 4 (UL)
Battery negative (-) → Terminal 1 (UL3)
Forward Direction
Battery positive (+) → Terminal 1 (UL3)
Battery negative (-) → Terminal 4 (UL)
Inverse Direction


If the result is not as specified, replace the door control motor.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (PSW) - 6 (LS2) Initial stop → Initial switch Below 1 Ω
3(PSW) - 6(LS2)
2(L-) - 5(ANRL)
Initial switch → Full switch 10 kΩ or higher
2(L-) - 5(ANRL) Full switch → Full stop Below 1 Ω


If the result is not as specified, replace the door control motor.



Hide 69330B 3.INSPECT GLIDE DOOR FRONT LOCK ASSEMBLY

a.

Check the operation of the glide door front lock assembly.

B556726C02
1.74,1.542 1.427,0.813 1.427,0.813 1,0.813 true 1.74,1.625 1.438,1.24 1.438,1.24 1,1.24 true 1.729,1.844 1,1.844 true 2.708,4.063 2.573,4.063 2.573,4.063 2.385,3.646 true 2.708,3.073 2.573,3.073 2.573,3.073 2.385,3.344 true 2.563,4.396 2.427,4.396 2.427,4.396 2.156,3.646 true 1.313,4.063 1.469,4.063 1.469,4.063 1.615,3.646 true 1.427,4.396 1.646,4.396 1.646,4.396 1.833,3.646 true 1.344,3.073 1.458,3.073 1.458,3.073 1.635,3.344 true 1.458,2.844 1.615,2.844 1.615,2.844 1.833,3.344 true 4.104,1.323 4.417,1.479 0.313,0.156 10 false *a 4.552,1.333 4.865,1.49 0.313,0.156 10 false *b 4.979,1.323 5.292,1.479 0.313,0.156 10 false *c 5.552,1.333 5.865,1.49 0.313,0.156 10 false *d 3.469,1.865 3.781,2.021 0.313,0.156 10 false *e 3.49,2.5 3.802,2.656 0.313,0.156 10 false *f 3.469,2.938 3.781,3.094 0.313,0.156 10 false *g 3.479,3.313 3.792,3.469 0.313,0.156 10 false *h 0.552,2.896 0.865,3.052 0.313,0.156 10 false *j 2.76,3.99 3.25,4.156 0.49,0.167 10 false ACT+ 3.938,1.594 4.25,1.792 0.313,0.198 10 false ON 3.875,1.771 4.333,1.969 0.458,0.198 10 false OFF 3.938,1.979 4.25,2.177 0.313,0.198 10 false ON 3.875,2.135 4.333,2.333 0.458,0.198 10 false OFF 3.76,2.667 4.281,2.917 0.521,0.25 10 false Return 3.75,2.354 4.271,2.583 0.521,0.229 10 false Closer 3.854,2.5 4.344,2.698 0.49,0.198 10 false Stop 3.948,2.885 4.26,3.083 0.313,0.198 10 false ON 3.875,3.042 4.333,3.24 0.458,0.198 10 false OFF 3.875,3.406 4.333,3.604 0.458,0.198 10 false OFF 3.948,3.229 4.26,3.427 0.313,0.198 10 false ON 0.833,0.75 1.146,0.906 0.313,0.156 10 false *d 0.823,1.167 1.135,1.323 0.313,0.156 10 false *c 0.833,1.781 1.146,1.938 0.313,0.156 10 false *b 2.75,2.99 3.24,3.156 0.49,0.167 10 false ACT- 2.625,4.323 3.115,4.49 0.49,0.167 10 false E1 1.063,4.01 1.552,4.177 0.49,0.167 10 false FUL 1.156,4.333 1.646,4.5 0.49,0.167 10 false POL 1.063,3.021 1.552,3.188 0.49,0.167 10 false HND 1.188,2.792 1.677,2.958 0.49,0.167 10 false HAF 6.323,3.833 6.635,3.99 0.313,0.156 10 false *i
*a Open-latch Position *b Half-latch Position
*c Full-latch Position *d Over-latch Position
*e Latch Switch *f Motor
*g Initial Position Switch *h Pawl Swithc
*i Close Operation *j Component without harness connected
(Glide Door Front Lock Assembly)


i.

Apply battery voltage and check the operation of the glide door front lock motor.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 1 (ACT-)
Battery negative (-) → Terminal 5 (ACT+)
Close Operation
Battery positive (+) → Terminal 5 (ACT+)
Battery negative (-) → Terminal 1 (ACT-)
Release Operation


If the result is not as specified, replace the glide door front lock assembly.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Initial Poition Switch
Tester Connection Condition Specified Condition
4(HND) - 6(E1) Open-latch Position Below 1 Ω
Close Operation 10 kΩ or higher

Latch Switch
Tester Connection Condition Specified Condition
3(HAF) - 6(E1) Open-latch Position Below 1 Ω
Half-latch Position 10 kΩ or higher
Full-latch Position 10 kΩ or higher
Over-latch Position Below 1 Ω
8(FUL) - 6(E1) Open-latch Position Below 1 Ω
Half-latch Position Below 1 Ω
Full-latch Position 10 kΩ or higher
Over-latch Position 10 kΩ or higher

Pawl Switch
Tester Connection Condition Specified Condition
7(POL) - 6(E1) Initial Position 10 kΩ or higher
Release Position Below 1 Ω


If the result is not as specified, replace the glide door front lock assembly.



Hide 69340A 4.INSPECT GLIDE DOOR REAR LOCK ASSEMBLY

a.

Check the operation of the glide door rear lock assembly.

B556727C02
1.948,3.802 2.188,4.125 2.188,4.125 2.323,4.125 true 2.042,1.76 2.51,0.99 2.51,0.99 2.75,0.99 true 1.948,1.75 1.385,0.698 1.385,0.698 1.01,0.698 true 1.667,1.76 1.313,1.167 1.313,1.167 0.792,1.167 true 1.771,3.823 2,4.427 2,4.427 2.302,4.427 true 1.948,3.604 2.313,3.604 true 0.99,3.615 1.354,3.615 true 1.354,3.813 1.167,4.135 1.167,4.135 0.969,4.135 true 1.552,3.823 1.292,4.427 1.292,4.427 1,4.427 true 1.531,3.573 1.25,3.198 1.25,3.198 1.021,3.198 true 4.094,1.25 4.406,1.406 0.313,0.156 10 false *a 4.781,1.26 5.094,1.417 0.313,0.156 10 false *b 5.656,1.25 5.969,1.406 0.313,0.156 10 false *c 6.281,1.25 6.594,1.406 0.313,0.156 10 false *d 3.458,1.646 3.771,1.802 0.313,0.156 10 false *e 3.479,2.052 3.792,2.208 0.313,0.156 10 false *f 3.458,2.417 3.823,2.667 0.365,0.25 10 false *g 3.458,2.885 3.771,3.042 0.313,0.156 10 false *h 3.49,3.438 3.76,3.625 0.271,0.188 10 false *i 6.865,3.802 7.125,3.969 0.26,0.167 10 false *j 3.854,1.75 4.313,1.948 0.458,0.198 10 false OFF 3.854,3.531 4.313,3.729 0.458,0.198 10 false OFF 3.854,2.135 4.313,2.333 0.458,0.198 10 false OFF 3.854,2.521 4.313,2.719 0.458,0.198 10 false OFF 3.917,3.354 4.375,3.552 0.458,0.198 10 false ON 3.917,2.365 4.375,2.563 0.458,0.198 10 false ON 3.917,1.969 4.375,2.167 0.458,0.198 10 false ON 3.917,1.583 4.375,1.781 0.458,0.198 10 false ON 3.833,2.885 4.292,3.083 0.458,0.198 10 false Stop 3.729,3.052 4.333,3.25 0.604,0.198 10 false Return 3.729,2.729 4.313,2.927 0.583,0.198 10 false Closer 0.406,3.01 0.667,3.177 0.26,0.167 10 false *k 2.781,0.938 3.094,1.094 0.313,0.156 10 false *d 0.833,0.625 1.146,0.781 0.313,0.156 10 false *c 0.635,1.094 0.948,1.25 0.313,0.156 10 false *b 2.375,4.052 2.833,4.25 0.458,0.198 10 false ACT+ 2.354,4.333 2.813,4.531 0.458,0.198 10 false E2 2.375,3.531 2.833,3.729 0.458,0.198 10 false ACT- 0.698,3.563 1.156,3.76 0.458,0.198 10 false MVL 0.771,4.073 1.229,4.271 0.458,0.198 10 false UL 0.646,4.354 1.104,4.552 0.458,0.198 10 false LSSR 0.844,3.146 1.302,3.344 0.458,0.198 10 false L1
*a Open-latch Position *b Half-latch Position
*c Full-latch Position *d Over-latch Position
*e Half-latch Switch *f Full-latch Switch
*g Pawl Swithc *h Motor
*i Initial Position Switch *j Close Operation
*k Component without harness connected
(Glide Door Front Lock Assembly)
- -


i.

Apply battery voltage and check the operation of the glide door rear lock motor.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 4 (ACT-)
Battery negative (-) → Terminal 8 (ACT+)
Close Operation
Battery positive (+) → Terminal 8 (ACT+)
Battery negative (-) → Terminal 4 (ACT-)
Release Operation


If the result is not as specified, replace the glide door rear lock assembly.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Initial Poition Switch
Tester Connection Condition Specified Condition
5(UL) - 7(E2) Open-latch Position 10 kΩ or higher
Close Operation Below 1 Ω

Half Latch Switch
Tester Connection Condition Specified Condition
2(L1) - 7(E2) Open-latch Position Below 1 Ω
Half-latch Position 10 kΩ or higher
Full-latch Position 10 kΩ or higher
Over-latch Position 10 kΩ or higher

Half Latch Switch
Tester Connection Condition Specified Condition
1(MVL) - 7(E2) Open-latch Position Below 1 Ω
Half-latch Position Below 1 Ω
Full-latch Position 10 kΩ or higher
Over-latch Position 10 kΩ or higher

Pawl Switch
Tester Connection Condition Specified Condition
6(LSSR) - 7(E2) Initial Position 10 kΩ or higher
Release Position Below 1 Ω


If the result is not as specified, replace the glide door rear lock assembly.



Hide 69630A 5.INSPECT GLIDE DOOR LOCK REMOTE CONTROL ASSEMBLY

a.
B556728C02
0.354,2.729 0.677,2.594 true 1.26,2.698 0.969,2.604 true 0.333,0.281 0.646,0.438 0.313,0.156 10 false *a 1.771,0.313 2.083,0.469 0.313,0.156 10 false *b 0.25,2.063 0.563,2.219 0.313,0.156 10 false *c 1.333,2.667 1.646,2.823 0.313,0.156 10 false B 0.24,2.719 0.552,2.875 0.313,0.156 10 false E
*a for Inside Handle
*b for Outside Handle
*c Component without harness connected
(Glide Door Lock Remote Control Assembly)
V100135

Open Side
V100136

Close Side


Check the resistance of the glide door lock remote control assembly.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Handle Switch (Open Operation)
Tester Connection Condition Specified Condition
1(B) - 2(E) Handle pulled (open side) Below 1 Ω
Neutral position 10 kΩ or higher

Handle Switch (Close Operation)
Tester Connection Condition Specified Condition
1(B) - 2(E) Handle pulled (close side) Below 1 Ω
Neutral position 10 kΩ or higher


If the result is not as specified, replace the glide door lock remote control assembly.



b.
B556729C02
0.188,0.177 0.5,0.333 0.313,0.156 10 false *a
*a Component without harness connected
(Glide Door Lock Remote Control Assembly)
V100135

Locked
V100136

Unlocked


Check the operation of the glide door lock remote control assembly.

i.

Apply battery voltage and check the operation of the door lock actuator.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 3
Locked
Battery positive (+) → Terminal 3
Battery negative (-) → Terminal 2
Unlocked


If the result is not as specified, replace the glide door lock remote control assembly.